Resumo do conteúdo contido na página número 1
INVINCIBLE "RS" OWNERS
MANUAL
R6
1
Resumo do conteúdo contido na página número 2
Contents Packing List 3 Installation & Assembly 3 Venting 5 Operation 9 ESP Control 12 Maintenance 13 Wiring Diagram 16 Feeder Parts 17 Trouble Shooting 18 Specifications 19 Warnings 20 Manufactured by Harman Stove Company 352 Mountain House Road Halifax Pa. 17032 (717) 362-9080 2
Resumo do conteúdo contido na página número 3
Packing List Inside Stove: Hardware Pack (2) Electrical Terminals (1) 10-32 x 1/2" Bolt (1) 1/4 x 20 x 2 1/2" Bolt (1) Wooden Handle (1) Brass Knob (1) Owners Manual (1) Warranty Activation Coupon (1) Room Sensing Probe (1) Ash Pan (2) Firebricks (1) Scraper (1) Flame Guide (1) Cleaning Brush Assembly and Installation Hopper Knob Final Assembly Remove parts from ash pan. Install Wooden Door Handle with 1/4 x 20 x 2 1/2 bolt. Install Brass Hopper Knob with 10-32 x 1/2 bolt. Install the t
Resumo do conteúdo contido na página número 4
Installing Place the stove on a noncombustible floor pro- 3" tector and away from combustible walls at least as far as shown in figure 2 and 3. Note that the clear- ances shown are minimum for safety but do not leave much room for access when cleaning or servicing. Please take this into account when placing the stove. Place the Room Sensing Probe in the desired location and run standard thermostat wire back to the terminals on the back of the stove and connect with the two terminals provided.
Resumo do conteúdo contido na página número 5
Venting A combustion blower is used to extract the com- bustion gases from the firebox. This causes a nega- tive pressure in the firebox and a positive pressure in the venting system as shown in fig. 4. The longer the vent pipe and more elbows used in the system, the greater the flow resistance. Because of these facts we recommend using as few elbows as possible and 15 feet or less of vent pipe. If more than 15 feet of pipe is needed, the diameter should be increased from 3" to 4" because a larg
Resumo do conteúdo contido na página número 6
#1 Preferred method This method provides excellent venting for nor- mal operation and allows the stove to be installed closest to the wall. Two inches from the wall is safe, however, four inches allows better access to remove the rear panel. The vertical portion of the vent should be three to five feet high. This vertical section will provide natural draft in the event of a power failure. 3 ft. to combustibles Fig. 5 #2 Preferred method This method also provides excellent venting for normal oper
Resumo do conteúdo contido na página número 7
#4 Installing into an existing chimney ( US only ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable you may want to install a liner as in method #7. Fig. 7 #5 Installing into an existing fireplace chimney ( US only ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. The damper area m
Resumo do conteúdo contido na página número 8
#6 Installing into an existing fireplace chimney ( US and Canada ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. In Canada and some places in the US it is re- quired that the vent pipe extend all the way to the top of the chimney. In this method a cap should also be installed on the chimney to keep out rain. Be sure to use approved pellet vent pipe fittings. Seal pipe joints with silicone in addition to th
Resumo do conteúdo contido na página número 9
DO NOT INSTALL A FLUE DAMPER IN THE WARNING EXHAUST VENTING SYSTEM OF THIS DO NOT INSTALL IN SLEEPING ROOM UNIT. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER CAUTION APPLIANCE. THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND INSTALL VENT AT CLEARANCES CEILING/ROOF MUST BE MAINTAINED. SPECIFIED BY THE MANUFACTURER Mobile home installation should be done in accordance with the Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24. WARNING 3' Keep combustible mat
Resumo do conteúdo contido na página número 10
Operation Starting First Fire Be sure the power cord is plugged into a 120 volt receptacle. This can be verified by the red power light on the control panel. Fill the hopper with pellets, fig. 12. Fill the burn pot with pellets to a level just short Fig. 8 of overflowing, fig. 8. Adjust feed rate. If this is your first fire or you are trying different pellets, set the feed adjuster to "3", fig. 9. This is a conservative number and will probably need to be increased. After you know a feed rate s
Resumo do conteúdo contido na página número 11
Scrape floor of burn pot with scraper to Starting a fire after proper remove any carbon build-up before starting a new fire. Feed Rate is known. Clean burn pot with scraper (supplied). Fill the hopper with pellets. Fill the burn pot with pellets to a level just short of overflowing. Adjust feed rate to proper setting. After you know what feed rate works well, then use that setting. (For example a setting of "5" Fig. 11 produces 1" or more of ash on the burn pot with the brand of pellets you ar
Resumo do conteúdo contido na página número 12
Fig. 13 When to use "Stove Temp Mode" In "Stove Temp Mode" the Stove Temp Dial determines the temperature of the stove. Heat output and fuel consumption will remain con- stant. This makes it possible to tell how long a hopper full of pellets will last. The distribution blower speed will vary according to the position of the mode selector, fig. 13. When to use "Room Temp Mode" In "Room Temp Mode" heat output is controlled automatically by the Room Sensing Probe. When the Room Sensing Probe calls
Resumo do conteúdo contido na página número 13
ESP CONTROL Power Light Indicates power to the control. Feed adjuster Secondary function: Sets the maximum feed Blinks every 15 seconds rate when the feed adjuster is in "Test Mode". This verifies feeder switch Test operation. Should be lit Runs all motors at anytime the unit is pluged full speed for two in. minutes to check Status Light operation. After two Will be lit in either stove minutes the stove or room temp mode when will go to minimum pointer is not within off burn and the blower
