Resumo do conteúdo contido na página número 1
PT1520MU
Touchscreen LCD Monitor
USER’S GUIDE
www.planar.com
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Important Recycle Instructions: LCD Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. .
Resumo do conteúdo contido na página número 4
Resumo do conteúdo contido na página número 5
1 Table of Contents Usage Notice Precautions .........................................................................................2 Introduction About Planar’s PT1520MU..................................................................3 Touch Screen for PT1520MU…………………………………………….4 Package Overview ..............................................................................5 Installation Product Overview..................................................................
Resumo do conteúdo contido na página número 6
2 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass
Resumo do conteúdo contido na página número 7
3 Introduction About Planar’s PT1520MU The PT1520MU is a 15” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct analog signal input Active matrix TFT LCD technology 1024x768 XGA resolution 15” viewable display area 31.5 ~ 60 kHz horizontal scan 56 ~ 75 Hz refresh rate Auto -adjustment function Multilingual OSD user controls VESA DPMS power saving Kensington security slot Built-in speakers for
Resumo do conteúdo contido na página número 8
4 Touch Screen for PT1520MU 3m® 5-wire Resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: USB Durability: 35 million touches at a single point Hardness of surface: 4H per ASTM D3363-92 Operating force: Stylus- <25 g (average) Finger - <50 g (average) Transmissivity: 83% (Typ.) + 2% Haze: 5% (Typ.) Driver: 3m® MT 7.11. Supports Microsoft Windows® 2000, XP
Resumo do conteúdo contido na página número 9
5 Package Overview LCD Display Power Adapter Power Cord VGA Signal Cable Audio-in Cable USB Cable User’s Guide Landing Strip Touchscreen Driver Installation CD-ROM
Resumo do conteúdo contido na página número 10
6 Installation Product Overview Front View Liquid Crystal Display (LCD Display) Panel Controls Stand Back View Connector Ports as shown below DC VGA Audio-in USB Power-In input
Resumo do conteúdo contido na página número 11
7 Tilt Turn the knob. Once loosened, grasp the LCD display with both hands to adjust the tilt as desired. Tighten the knob once the display is in the desired location. Tilt Angle:0 °~90 ° Knob Kensington® Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included. Kensington Security Slot
Resumo do conteúdo contido na página número 12
8 VESA Mount This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. The 75 mm VESA hole pattern is located inside the rear cover (shown in the following figure). To mount the monitor on a swing arm or other mount
Resumo do conteúdo contido na página número 13
9 Cable Management . 1. Pull all the cables backward while the tilt angle is 0 °. 2. Pull all the cables forward while the tilt angle is 90 °.
Resumo do conteúdo contido na página número 14
10 Start Your Installation Connecting the Display (Figure 10.1) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC power cord to the power connector; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet ( ). 3. Connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws ( ). 4. Con
Resumo do conteúdo contido na página número 15
11 Figure 10.1 Power Cord VGA Cable Audio-In USB Cable Cable
Resumo do conteúdo contido na página número 16
12 User Controls Front Panel Controls No / Icon Control Function Power Switch Turns on/ off the power of the LCD display. 1. Green indicates the display is turned on. Power LED 2. Amber indicates the display is in power-saving mode. Select - To select the adjustment items from OSD menus. Select/Auto S Auto - To activate the “Auto Adjustment” function to obtain an optimum image. 1. Increases the brightness o
Resumo do conteúdo contido na página número 17
13 How to Use the OSD Menus 1. Press the "MENU" button to pop up the “on-screen menu” and to select among the four main menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “+”or “-“ button. 4. The OSD menu will automatically close if you have left it idle for a pre-set amount of time. 5. To disable the OSD menu buttons, please follow the instructions below. Please note: the monitor has to be ON with
Resumo do conteúdo contido na página número 18
14 On-Screen Display Menus Main Menu Menu Level 2 Function Description Remark Auto-Adjustment Choose this function to obtain an optimum image. Adjusts the contrast of the display image. The range is Default is 50 Contrast 0~100. Adjusts the brightness of the image. The range is Default is 70 Brightness 0~100. Horizontal Position Changes the horizontal position of the image. Vertical Position Changes the vertical position of the image. Page 1 Changes the displays data frequenc
Resumo do conteúdo contido na página número 19
15 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact Planar. Problem: No image appears on screen. Check that all the I/O and power connectors are correctly installed and well connected as described in the “Installation” section. Make sure the pins of the connectors are not crooked or broken. Reconfigure the resolution of your computer to make it less than or equal to 1024 x 768. Problem
Resumo do conteúdo contido na página número 20
16 Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There are three kinds of sources for this problem. Please check the cable connections or contact Planar for more information. No Signal This message means that the LCD Display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and VGA signal c
