Resumo do conteúdo contido na página número 1
The lightning flash with arrowhead
symbol, within an equilateral triangle is
CAUTION
intended to alert the user to the presence
of uninsulated “dangerous voltage”
RISK OF ELECTRICAL SHOCK
within the product’s enclosure that may
DO NOT OPEN
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
To reduce the risk of electric shock. Do
CAUTION:
equilateral triangle is intended to alert
not remove cover (or back). No user
the user t
Resumo do conteúdo contido na página número 2
2 Safety Precautions Under the following conditions, The AC power supply is controlled by turning on/ WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO 1. Turn off the power. off the POWER switch on the rear panel. If the RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE 2. Unplug this product from the wall outlet. product is installed in a place where you cannot PLACED ON THE APPARATUS. 3. Refer service to qualified service personne
Resumo do conteúdo contido na página número 3
U.S.A. only European Union only FCC NOTICE EMC Supplement CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. This equipment is in conformity with the provisions and protection requirements of the corresponding NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, European Directives. This equipment is designed for professional video appliances and can be used in the pursuant to Part
Resumo do conteúdo contido na página número 4
4 Installation CAUTION Higher position Do not rest your arm on the monitor or lean against the monitor. Do not touch the LCD panel when installing the monitor. Make sure to install the monitor securely to prevent the monitor from falling over, which causes damage to the monitor or injury. When shipped from factory, the stand is attached to the monitor. You can tilt the monitor from about 20° upward to about 10° downward. Monitor Stand When the monitor is not tilted (0°), the guidelines
Resumo do conteúdo contido na página número 5
Lower position To prevent an accidental fall Fix the monitor to a wall by using strings. Fixing the monitor Attachment screws Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two 100 mm pitch holes on the upper side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a wall or a pillar using durable string. Stand Monitor Hook (not provided) Hook and screws (M4 x 10 mm) (not provided) ENGLISH 5 D DT-V9L1D_EA_EN_R.indd
Resumo do conteúdo contido na página número 6
6 Daily Operations / Connections 7 Front panel “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not actually work). The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light). 8 A. MARKER button/lamp r FOCUS button/lamp Displays/hides the area marker. Helps to focus the picture. Select the styl
Resumo do conteúdo contido na página número 7
Menu Operations Audio Channel Selection About the Information Display About the Status Display Select the audio channels when the SDI is The monitor displays the information below If you press the input button of the current input, 1 Display the menu. selected as a signal input and EMBEDDED depending on the settings of the menu and the status of the input signal and setting of muting To display the MAIN MENU AUDIO signals come in. buttons. are displayed for about 3 seconds. \ Press MENU button
Resumo do conteúdo contido na página número 8
8 Daily Operations / Connections (cont.) 7 Rear panel Note for connections Before making any connections, turn off all the equipment. Use a cord whose plugs correctly match the terminals on this monitor and the equipment. Plugs should be firmly inserted; poor connections could cause noise. When unplugging a cord, be sure to grasp its plug and pull it out. DO NOT connect the power cord until all connections are completed. Refer also to the user manual of each piece of equipment. CAUT
Resumo do conteúdo contido na página número 9
7 Available signals Attaching the Power Cord Holder Input terminal Signal format shown CAUTION VIDEO/COMPONENT No. Signal name in the status display E. AUDIO HD/ Depending on the type of external batteries, the cover may not be attached to the case. VBS Y/PB/PR 1 (☞ page 7) SD SDI* (Composite) (Analog component) The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN 2 1 NTSC* NTSC √ —— terminal. 2PAL PAL √ —— The power cord holder consists of
Resumo do conteúdo contido na página número 10
10 Menu Configuration—MAIN MENU For the operation procedure, see page 7. PICTURE IMPROVEMENT Setting for the picture quality Item To do Setting value 1 APERTURE* Select the frequency of the luminance signal compensated in OFF, LOW, HIGH “APERTURE LEVEL.” APERTURE Compensate the frequency response of the luminance signal of the 01 – 10 1 LEVEL* video signal. sub menu Display the sub menu which enables you to adjust the items of “PICTURE IMPROVEMENT” while viewing the actual picture. reset Restor
Resumo do conteúdo contido na página número 11
AUDIO SETTING Setting for the audio channel group of the EMBEDDED AUDIO signals and level meter Item To do Setting value E.AUDIO GROUP Select the audio channel group of the ☞ “NOTE” EMBEDDED AUDIO signals. BAR POSITION Select the type of the level meter display VERT. (vertically), HORZ. (horizontally) — vertically or horizontally. LEVEL METER ch Select the number of the audio channels OFF, 12CH, 8CH displayed on the level meter. CH ARRANGE Select the order of the audio channels LINE, DIVIDE (☞
Resumo do conteúdo contido na página número 12
12 Menu Configuration—SET-UP MENU For the operation procedure, see page 7. FUNCTION SETTING Setting for the sub menu display, color system, color of the tally lamp, and format indicator Item To do Setting value sub menu POSI. Select the contents and displaying position of “sub menu.” ☞ “NOTE” COLOR SYSTEM Select the color system. AUTO, NTSC, PAL If the picture is unstable with “AUTO,” select “NTSC” or “PAL.” TALLY SELECT Select the color of the tally lamp. GREEN, RED FORMAT INDICATOR Select wh
Resumo do conteúdo contido na página número 13
REMOTE SETTING (☞ “External Control” on pages 14 and 15) Setting for the external control Item To do Setting value TYPE SEL. Select the external control method for the MAKE, TRIGGER, SET MAKE/TRIGGER terminal. PIN1, PIN2, PIN3, Assign the control functions to the pins of COLOR OFF, SCR CHECK, A.MARKER, PIN4, PIN5 the MAKE/TRIGGER terminal. S.MARKER, FOCUS, DYNAMIC, SDI, VIDEO/ Assign a function to each pin terminal COMPO., ASPECT, TALLY SEL, SOURCE ID, by selecting “SET” in “TYPE SEL.” MUTIN
Resumo do conteúdo contido na página número 14
14 External Control To assign the functions to the pin terminals 7 About the external control For the operation procedure, see page 7. This monitor has two external control terminals. 1 Select “REMOTE SETTING” on the SET-UP MENU. MAKE/TRIGGER terminal (RJ-45): The following external control systems are available. 2 Set “TYPE SEL.” to “SET.” (1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to 3 Select a pin name (“PIN1” – “PIN5”) for whic
Resumo do conteúdo contido na página número 15
Operation 1 Set “TYPE SEL.” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU. No. Commands Functions Data 2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled 1! 00 BC N1 Cr Starts communication (connection) No data by the external control. 2! 00 BC N0 Cr Terminates communication (termination) No data 3 When selecting “MAKE” system: Operate each function by short-circuiting the corresponding pin termi
Resumo do conteúdo contido na página número 16
16 Troubleshooting The following are not malfunctions. Solutions to common problems related to the monitor are described here. If none of the solutions presented here solves the problem, unplug the monitor and consult an authorized dealer or service center. When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed. Though the remaining picture will disappear after a while, there may be a case that it remains Symptom Probable caus
Resumo do conteúdo contido na página número 17
Ω Ω Specifications 7 General 7 Input/output terminals Model name DT-V9L1D VBS/Y Composite signal/analog component (Y) signal input/output: Type Multi format LCD monitor 1 line, BNC connector x 2 Screen size Type 9 wide format 1 V(p-p), 75 Aspect ratio 15:9 * The input (IN) and output (OUT) VIDEO/COMPONENT LCD panel 9˝ wide, IPS-Pro terminals are bridge-connected (auto (IN/OUT) termination) Width: 195 mm Effective screen size PB, PR Height: 117 mm Analog component (PB, PR) signal input:
Resumo do conteúdo contido na página número 18
18 Specifications (cont.) Unit: mm 7 Dimensions When the stand is attached to the When the stand is attached to the higher position. lower position. 116 VESA mounting holes 100 27.5 (8-M4, depth: 10 mm) 1.5 75 222.4 202 13 186 185 * at the higher position ** at the lower position tapped hole (3/8˝) tapped hole (1/4˝) DT-V9L1D_EA_EN_R.indd 18 DT-V9L1D_EA_EN_R.indd 18 0 07.9.14 6:19:32 PM 7.9.14 6:19:32 PM 218*/181** 176 55 100 37.5 75
