Resumo do conteúdo contido na página número 1
OPERATING INSTRUCTIONS
42 Widescreen Plasma HDTV Monitor
PDP4273M
Resumo do conteúdo contido na página número 2
1. Safety Guidelines Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA ..................... UL Canada ................ CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi
Resumo do conteúdo contido na página número 3
2. Important Safeguards Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before starting the operation. The User Manual uses the following symbols to ensure a safe operation and prevent any damage to o
Resumo do conteúdo contido na página número 4
Never use a damaged power cord: Heavy objects, heat or tensile force may damage the power cord and cause fire or electric shock. Do not change or open the back cover: Removing the back cover of the product may cause fire or electric shock. Contact the manufacturer when inspection or adjustment is required. Do not use the product if any abnormality occurs: If any smoke or odor becomes apparent, unplug the connector and contact the manufacturer immediately. Do not try to repair the product by yo
Resumo do conteúdo contido na página número 5
Unplug the connector Hold the power connector when removing the power cable: Pulling the power cable itself may damage the wires inside the cable and cause fire or electric shock. Do not touch the connector with wet hands: To avoid risk of electric shock. ATTENTION Insert batteries in accordance with instructions: Insert the batteries with correct polarities (positive and negative ). Incorrect polarities may cause breakage and leakage of the batteries, hurt operators and contaminate the remot
Resumo do conteúdo contido na página número 6
1. Read all safety instructions and the User Manual before using the product. 2. The safety instructions and User Manual should be maintained in good condition for future reference. 3. Unplug the power connector before cleaning the product. A wet cloth is sufficient for the cleaning of the product, never use liquid or spray cleaner for cleaning the product. 4. Always use the accessories recommended by the manufacturer to avoid any risk. 5. When moving the product fro
Resumo do conteúdo contido na página número 7
Contents 1. Before use ..................................................................................................... 7 1.1 Open the Package .........................................................................................7 1.2 Installation ......................................................................................................7 2. Product Features ........................................................................................... 8 3. Accessories ..........
Resumo do conteúdo contido na página número 8
1. Before use The product is a 42” WXGA (WXGA resolution) Plasma Display. It has passed the Class-B EMC test and the UL and cUL safety certifications, and is ideal for both consumer and commercial use. The product is a precise electronic product. Users should read the following instructions carefully to maximise the performance of the product: 1.1 Open the Package - The product is packaged in a carton together with other standard accessories. Any optional accessories shall be
Resumo do conteúdo contido na página número 9
2. Product Features The 42” PDP provides quality image displays and is suitable for a variety of multimedia applications: 1. Available input signals - The standard PC module provides VGA (D-SUB 15 PIN) and HDMI input connectors. The product supports PC image resolutions up to (1024 x 768@60Hz) with a vertical frequency of 60 Hz. - The Video module provides composite video (RCA), S-Video (DIN 5 PIN) and component video (RCA) input connectors. It supports the quality input images of DVD
Resumo do conteúdo contido na página número 10
4. Names and Functions of Parts 4.1 Side View - Connect the power cable to the product then connect the main plug to the wall outlet. - Push the power switch (O: Off, I: On). The power indicator on the front of the panel should now display red, indicating that the plasma is in standby mode. Note: Shut down the power switch, turn on it again after the power indicator is extinguished entirely . Power Switch Power Inlet 9
Resumo do conteúdo contido na página número 11
4.2 Front View Sketch map 1 Remote control window: The receiving of Remote control signals window. 2 Power indicator: Indicator ON (red) Standby mode. Indicator ON (green) The unit power ON mode. 3 Buttons: The functions of the buttons are described as follows: SEL. VOL. SOURCE MENU STANDBY SOURCE: Press to display the source menu, Use ▲ or ▼ button to select AV, S-Video, YPbPr 1, YPbPr 2, VGA or HDMI, then press ► button to con
Resumo do conteúdo contido na página número 12
4.3 Rear View L BLACK RED RED BLACK R - + 1 Speaker Terminals: Can be used to connect external speakers with 8 Ohm impedance to the product. 2 Wall Mount fixing holes (six holes): Use the standard screws to fix the wall mount. 3 Signal input and other terminals: A. RS-232: The D-SUB 9 Pins terminal is used as a control port for serial communication between PC and Panel. (Only for after-sales service) B. HDMI INPUT: For high quality picture display purposes. Connects to HDMI or DVI (w
Resumo do conteúdo contido na página número 13
I. Video Input: Connect the video input terminal to the video output terminal of the video output device. Video Audio Input: Connect the audio input terminal to the audio output terminal of the video output device. J. S-Video INPUT: Connect the Y/C S-Video input terminal to the S-Video output terminal of the video output device. S-Video Audio INPUT: Connect the audio input terminal to the audio output terminal of the video output device. 4.4 Remote Control 1 Standby( ): Pr
Resumo do conteúdo contido na página número 14
13 Auto: The Display automatically adjusts the phase, vertical / horizontal position when pressing this button in VGA mode. 14 Menu: Press this button to pop up the OSD Menu and press it again to exit the OSD Menu. 15 V-Chip: Press this button to enter the V-Chip Function. (Only for AV or S-Video) 16 P. Still: Press this button to hold on the screen. Press again to normal. 17 C/C: Press this button to enter the Closed Caption Function. (Only for AV or S-Video) 18 Display: Press the b
Resumo do conteúdo contido na página número 15
Range of Remote Control Sketch map 20 20 30 30 - Ensure the remote control is pointed towards the remote control window on the display unit. - No obstacles should be placed between the remote control and the remote control window. - The effective receiving range for the signal is within 5-8 meters from the front of the remote control window, and 30° to the left or right side and 20° above or below the control window. Care For Remote Control - Avoid spilling liquids on
Resumo do conteúdo contido na página número 16
5. Connection to External Equipment D-Sub(VGA) PC Audio Connecting the Computer INPUT 1. Connect the PDP to the computer with the D-Sub (VGA) cable. 2. Connect the audio output of the computer to the audio input on the PDP. 3. Please ensure the Power Cord is connected and turned on the STANDBY button before it is operated. 4. Press STANDBY button on the remote control or on the PDP. 5. The PDP and Computer are working at the same time. Press SOURCE button to select VG
Resumo do conteúdo contido na página número 17
Connecting the DVD player or HDTV Set-top box using HDMI input 1. Connect the PDP to the DVD player or HDTV Set-top box with the HDMI cable. 2. Connect the DVI AUDIO input terminal to the audio output terminal of HDTV Set-top box with DVI output terminal, and a DVI to HDMI conversion cable should be adopted. 3. Please ensure the Power Cord is connected and turned on the STANDBY button before it is operated. 4. Press STANDBY button on the remote control or on the PDP. 5. The PDP
Resumo do conteúdo contido na página número 18
Connecting the DVD, VCR or other video apparatus 1. With an S-VIDEO cable connect the PDP to the VCR or other device. S-VIDEO will connect only the video portion (image only) of the signal. With an AUDIO cable (RCA type) connect the AUDIO OUT from the device to the AUDIO IN on the PDP. 2. With an AV cable connect to the Video plug of the PDP and the VCR or other video apparatus. With an AUDIO cable connect the audio output of the VIDEO of the VCR or other video apparatus to the audio
Resumo do conteúdo contido na página número 19
6. Basic Operation 6.1 Power ON/OFF: The Display is in Standby mode - Press Standby ( ) button on the remote control or on the front panel to turn on the unit. The power indicator changes from red to green. - Press Standby ( ) button on the remote control or on the front panel again to return the display to standby mode. The power indicator changes from green to red. Note: For protecting your PDP product, the interval time between turn on the PDP product and shut do
Resumo do conteúdo contido na página número 20
6.3 Other Function Swap: - Press this button on remote control to switch the Main window or Sub window picture in PIP or Split Screen. S. Sele: - Press this button to select the sound output from Main Window or Sub Window. W. Sele: - Press this button to select the Main Window or Sub Window. - When you want to select the signal source from the Main Window or Sub Window, you can press Source button to pop up “Source Select” menu, then use ▲ or ▼ button to select
