Resumo do conteúdo contido na página número 1
Cyber 1S1P PCI
Quick Installation Guide
Introducing the Cyber 1S1P PCI
The Cyber 1S1P PCI high-speed serial I/O card provides
one 9-pin serial port and one parallel port.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature reduces IRQ conflicts
• High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, lab
Resumo do conteúdo contido na página número 2
Package Contents • (1) Cyber 1S1P PCI board • (1) Driver CD • (1) Quick Installation Guide Layout JP1 Serial Port Parallel Port Figure 1. Layout Jumper Settings (JP1) Open = 0 volts (default) Short 1-2 = 5v Short 2-3 = 12v Note: Most serial devices do not require additional power through the serial port. Refer to your serial device's manual for more information. This jumper can be removed if it's not used. 2
Resumo do conteúdo contido na página número 3
Hardware Installation General instructions for installing the card are provided below, since the design of computer cases and motherboards vary. Refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the pow
Resumo do conteúdo contido na página número 4
Software Installation This section provides information on how to install the Cyber 1S1P PCI drivers. Windows 95 Driver Installation 1. At the Update Device Driver Wizard window, click Next. 2. Insert the driver CD, and click Other Locations. Type in D:\9x, click OK, then Finish. (Change D: to match your CD-ROM drive letter) 3. From the Insert Disk window, click OK. When the Copying Files dialog box appears, type in D:\9x, then click OK. 4. Repeat steps 1-3. 5. Restart Windows to complete the i
Resumo do conteúdo contido na página número 5
Windows ME Driver Installation 1. At the Add New Hardware Wizard, choose Specify the location of the driver (Advanced), then click Next. 2. Check Specify a location, uncheck the other box, insert the driver CD, type in D:\Me, then click Next. (Change D: to match your CD-ROM drive letter) 3. Click Next and Finish. 4. Repeat steps 1-3. 5. Restart Windows to complete the installation. To Verify Successful Installation In Windows 95/98/ 98SE/ME: 1. From the main desktop, right click My Computer, cl
Resumo do conteúdo contido na página número 6
7. Type in D:\NT4\Install_Parallel.exe, then click OK. (Change D: to match your CD-ROM drive letter) 8. Repeat steps 3-5. 9. Click Yes to restart Windows to complete the installation. To Verify Successful Installation In Windows NT 4.0: 1. Go to Start / Settings / Control Panel, double click Ports device icon. 2. A new COM port will be assigned when successfully installed. 3. Click Start, Programs, Administrative Tools, Windows NT Diagnostics. Click Resources tab, SIIGpar and SIIGser should be
Resumo do conteúdo contido na página número 7
2. Insert the driver CD, check Include this location in the search, uncheck the other check box, type in D:\XP, and click Next. (Change D: to match your CD-ROM drive letter) 3. At the Hardware Installation window, click Continue Anyway, then Finish. Our driver has been tested for stability and compatibility. 4. Repeat steps 1-3 two more times. 5. Restart Windows to complete the installation. Windows Server 2003 Driver Installation 1. At the Found New Hardware Wizard, choose Install from a list
Resumo do conteúdo contido na página número 8
Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 95/98/98SE/ME 1. From the Device Manager window double click Ports (COM & LPT), then double click CyberSerial PCI... serial port. 2. Click Settings tab, at the Port Name box click the down arrow and select a COM address that is not currently in use. 3. Click OK, click OK again to close Device Manager to save the changes. Windows 2000/
Resumo do conteúdo contido na página número 9
Changing Parallel Port Address (LPT) Some parallel devices need a specific parallel port in order to work. If your parallel device works properly, do not change this setting. Windows 95/98/98SE/ME 1. From the Device Manager window double click Ports (COM & LPT), then double click CyberParallel PCI. 2. Click Settings tab, check Enable use of I/O location 278h. 3. Click OK, click OK again to close Device Manager, and click Yes to restart Windows to save the changes. Windows 2000/XP/Server 2003 1.
Resumo do conteúdo contido na página número 10
Blank Page 10
Resumo do conteúdo contido na página número 11
Technical Support QUESTIONS? SIIG’s Online Support has the answers! Simply visit our Web site at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. The answers to your problems could be just a few clicks away. If you can't find answers or solutions to your questions, you have an option to submit the problems online to one of our technical support analysts and we will promptly respond to you with answers or solutions. The 5-year manu
Resumo do conteúdo contido na página número 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and all products are backed by a 5-year manufacturer warranty. High-quality control standards are ev
