Resumo do conteúdo contido na página número 1
CyberPro PCI 4S
Quick Installation Guide
Introducing the CyberPro PCI 4S
The CyberPro PCI 4S high-speed serial I/O card provides
four additional 9-pin serial ports. Depending on the
model purchased, this board will fit into either a Full or
Low Profile chassis.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature reduces IRQ conflicts
• High-speed serial port (9-
Resumo do conteúdo contido na página número 2
Package Contents • CyberPro PCI 4S board • 4-port fan-out cable • Low profile bracket (Dual Profile board only) • Driver CD • Quick installation guide Layout Full profile 4-pin power bracket JP1 JP2 connector (S1) (S2) (optional)* 44-pin connector JP4 JP3 (S4) (S3) Figure 1. Layout * Note: Make this connection only when two or more serial ports are configured for 5V/12V output. Depending on the model purchased, the bracket size will be either Full or Low Profile. Jumper Settings (JP1, JP2, JP
Resumo do conteúdo contido na página número 3
Fan-out Cable Serial ports DB9 44-pin (9-pin) connector Figure 2. Fan-out cable Hardware Installation General instructions for installing the card are provided below, since the design of computer cases and motherboards vary. Refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with
Resumo do conteúdo contido na página número 4
5. Change JP1-JP4 jumper settings to the desired voltage only if your serial device(s) needs additional power from the serial port. However, most serial devices do not require additional power. For more information, see Figure 1 on page 2. Skip this step if power is not required. 6. To install the card, carefully align the card's bus connector with the selected PCI slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 7. Replace the slot bracket's holding s
Resumo do conteúdo contido na página número 5
Windows 98/98SE 1. At the Add New Hardware Wizard, click Next. 2. Select Search for the best driver for your device (Recommend), then click Next. 3. Insert the driver CD, check Specify a location, uncheck the other boxes, , type in D:\9x, then click Next. (Change D: to match your CD-ROM drive letter) 4. Click Next, then Finish. 5. Repeat steps 1-4. 6. Restart Windows to complete the installation. Windows ME 1. At the Add New Hardware Wizard, select Specify the location of the driver (Advanced),
Resumo do conteúdo contido na página número 6
Windows NT 4.0 1. From the desktop click Start, then Run. 2. Insert the driver CD, type in D:\NT4\Install_serial.exe, then click OK. (Change D: to match your CD-ROM drive letter) 3. Click Next when the Welcome window appears. 4. Select Install, then click Next. 5. Click Yes, then click Exit. 6. Restart Windows to complete the installation. To Verify Windows NT 4.0 Installation 1. Click Start, Settings, Control Panel, double click Ports device icon. 2. Four new COM ports will be assigned when su
Resumo do conteúdo contido na página número 7
Windows XP 1. At the Found New Hardware Wizard, select Install from a list or specific location (Advanced), then click Next. 2. Insert the driver CD, check Include this location in the search, uncheck the other check box, type in D:\XP, and click Next. (Change D: to match your CD-ROM drive letter) 3. If the Hardware Installation window pops up, click Continue Anyway, then Finish. Our driver has been tested for stability and compatibility. 4. Repeat steps 1-3 five more times. 5. Restart Windows
Resumo do conteúdo contido na página número 8
2. Click on the + (plus sign) in front of Ports (COM & LPT), and CyberSerial PCI 16Cxxx... should be displayed four times. 3. Double click Multifunction adapters, SIIG CyberPro 4S PCI board should be displayed. Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 95/98/98SE/ME 1. From the Device Manager window double click Ports (COM & LPT), then double click the CyberSerial PCI serial
Resumo do conteúdo contido na página número 9
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. A lifetime manufacturer warranty supplied with this product is offered by SIIG, Inc. Please see SIIG website for more
Resumo do conteúdo contido na página número 10
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by t
