Resumo do conteúdo contido na página número 1
H8S/2169 Series TFP-144
User System Interface Cable
(HS2169ECN61H)
for E6000 Emulator
User’s Manual
HS2169ECN61HE(B)
Resumo do conteúdo contido na página número 2
Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice.
Resumo do conteúdo contido na página número 3
Preface Thank you for purchasing this user system interface cable (HS2169ECN61H) for the Renesas’s original microcomputer H8S/2169 series. The HS2169ECN61H is a user system interface cable that connects an H8S/2148 series E6000 emulator (HS2148EPI61H; hereinafter referred to as the emulator) to the IC socket for a TFP-144 package and expansion I/O board (HS2169EIO61H) for the H8S/2169 series MCU on the user system. i
Resumo do conteúdo contido na página número 4
Contents Section 1 Configuration....................................................................................1 Section 2 Connection Procedures......................................................................3 2.1 Connecting User System Interface Cable to Expansion I/O board ...................................3 2.2 Connecting User System Interface Cable to User System ................................................5 2.2.1 Installing IC Socket .............................
Resumo do conteúdo contido na página número 5
Section 1 Configuration CAUTION Use an NQPACK144SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2169ECN61H user system interface cable for the TFP-144 package. Figure 1 HS2169ECN61H User System Interface Cable 1
Resumo do conteúdo contido na página número 6
Table 1 lists the HS2169ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2169ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-144 package 4 Socket cover 1 For installing an TFP-144 packaged MCU 5 Screws (M2.0 x 10 mm) 4 For fastening cable head 6 Screws (M2.0 x 6 mm) 4 For installing an TFP-144 packaged MCU 7 Guide pins (φ 1 mm) 3 For determining the IC socket location 8
Resumo do conteúdo contido na página número 7
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Expansion I/O board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before
Resumo do conteúdo contido na página número 8
E6000 EMULATO Emulator station Expansion I/O board Cable body connector User system interface cable Figure 2 Connecting User System Interface Cable to Expansion I/O Board 4 USER INTERFACE CABL E6000 E6000
Resumo do conteúdo contido na página número 9
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system, the emulator product, and the expansion I/O board or will result in PERSONAL INJURY. The USER PROGRAM will be LOS
Resumo do conteúdo contido na página número 10
Use the guide pins provided to determine where to install the IC socket, as shown in figure 3. Pin 1 Guide pins 4 projections to apply IC socket epoxy resin adhesive to (NQPACK100SE manufactured by Tokyo Eletech Corporation) Bottom view of IC socket User system Figure 3 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for a TFP-144 package to the user system. CAUTION Be sure to completely solder the leads so that the solder slops gen
Resumo do conteúdo contido na página número 11
2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TFP-144 package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in figure 4. 2.2.4 Fastening Cable Head CAUTION 1. Use a screwdriver whose head matches the screw head. 2. The tightening torque must be 0.054 N•m or less. If the applied torque c
Resumo do conteúdo contido na página número 12
Fasten the user system interface cable head to the IC socket for an TFP-144 package on the user system with the four screws (M2.0 x 10 mm) provided. Each screw should be tightened a little at a time, alternating between screws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components. Figure 4 Connecting User System Interface Cable to User
Resumo do conteúdo contido na página número 13
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Removing Push the unfastening jig Unfastening jig Cable head User system Figure 5 Fastening Cable Body 9
Resumo do conteúdo contido na página número 14
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an TFP-144 package (NQPACK144SE: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the actual chip's mount pad. Figure 6 Recommended Dimensions for Mount Pad 10
Resumo do conteúdo contido na página número 15
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 11
Resumo do conteúdo contido na página número 16
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 8. Figure 8 Resulting Dimensions after Connecting User System Interface Cable 12
Resumo do conteúdo contido na página número 17
Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket
Resumo do conteúdo contido na página número 18
Figure 9 Installing MCU to User System 14
Resumo do conteúdo contido na página número 19
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2148 series, turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins with the MEMORY_FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3. The emulator
Resumo do conteúdo contido na página número 20
Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU. 3. To avoid breaking wires in the cable body, do not place heavy or sharp metal objects on the user system interface cable. 4. While the emulator station is connected to the user system with
