Resumo do conteúdo contido na página número 1
SBC-370
SOCKET 370 CELERON, PENTIUM III
Board Processor Guide
Resumo do conteúdo contido na página número 2
Brand or product names are trademarks or registered trademarks of their respective owners. Windows and Windows NT are registered trademarks of Microsoft Corp. in the United States and other countries. This document is copyrighted by Xycom Automation, Incorporated (Xycom Automation) and shall not be reproduced or copied without expressed written authorization from Xycom Automation. The information contained within this document is subject to change without notice. Xycom Automation does not guaran
Resumo do conteúdo contido na página número 3
Table of Contents 1. Features. . ..............................6 OVERVIEW .................................................6 Feature LIST.................................................6 CPU...................................................6 SDRAM.................................................6 AGP VGA Controller...........................................7 Ethernet Controller ...........................................7 Ultra DMA/33 Enhanced PCI EDI Interface ...............................7
Resumo do conteúdo contido na página número 4
LED Connector for LAN (CN5).....................................23 Fan Connector (CN13/CN14/CN15)..................................23 System Interrupts (IRQs)..........................................24 DMA Channel Assignments ........................................24 1st MB Memory Address Map .......................................25 I/OMap..................................................25 3. AMI BIOS Setup Menus .......................26 Getting Started......................................
Resumo do conteúdo contido na página número 5
1 Features OVERVIEW The Intel® Socket 370 Celeron® and Pentium III (FC-PGA) with AGP VGA and 10/100 Mbps Ethernet Single Board Computer (SBC-370) is a PICMG bus form factor board. It is equipped with a high performance Intel® Celeron processor (up to 500 MHz) or Pentium III (FC-PGA) 500 MHz (or above) processor, and advanced high performance multi-mode I/O. This board has a built-in DiskOnChip™ (DOC) Flash Disk for embedded applications. The DOC Flash Disk is 100% compatible to hard disk. Users
Resumo do conteúdo contido na página número 6
AGP VGA Controller S3 Trio® 3D/2x AGP VGA controller 133 MHz AGP bus speed Screen resolutions supported up to 1280 x 1024 x 64K colors @ 60 Mz refresh Screen resolutions also supported up to: 1600 x 1200 x 64K colors at 85 Hz refresh, non-interlaced mode 1024 x 768 x 16M colors at 85 Hz refresh, non-interlaced mode Ethernet Controller Realtek RTL8139 IEEE802.u 100 BaseTX standard Dual Auto-sensing interface to 10Mbps, 100Mbps Network RJ45 connector for 10 BaseTX and 100 BaseTX
Resumo do conteúdo contido na página número 7
Hardware Monitoring System Built-in LM78 hardware monitoring system Monitors power supply voltage and fan speed status IrDA Port Supports Serial Infrared (SIR) and Amplitude Shift Keyed IR(ASKIR) interface USB Port Supports two USB ports for future expansion ISAPLUS Enhance the ISA bus drive capability E2Key™ 1Kbit EEPROM (nonvolatile memory) Accepts read/write data by customer's program Stores system ID, password, and critical data on the board Watchdog Timer Can be set by 1,
Resumo do conteúdo contido na página número 8
Operating Humidity 5 - 95%, non-condensing WATCHDOG TIMER The Watchdog Timer is provided to ensure that standalone systems can recover from catastrophic conditions that cause the CPU to crash. This condition can occur from ex- ternal EMI or a software bug. When the CPU stops working correctly, hardware on the board will either perform a hardware reset (cold boot) or a Non-Maskable Interrupt (NMI) to bring the system back to a known state. Two I/O ports control the Watchdog Timer: 443 (hex) Rea
Resumo do conteúdo contido na página número 9
The E2KEY.OBJ provides two library functions for you to integrate your application 2 with the E KEY function. The read_e2key and write_e2key libraries are written and compiled in C language. To implement them, refer to the functions below: */unsigned int read_e2key(unsigned int address): This function will return the 2 E KEY data to a certain address. The address range is from 0 to 63. Return data is one word, 16 bits. */void write_e2key(unsigned int address, unsigned data): This function will w
Resumo do conteúdo contido na página número 10
2 Board Configuration BOARD LAYOUT Figure 2. SBC-370 Configuration. JP3, CPU Frequency JP8, CPU Multiplier Setting JP5, Watchdog Timer Type Setting JP12, Watchdog Timeout Period JP11, DiskOnChip Memory Address Setting JP4, Clear CMOS Setup JP7, PS/2 Mouse Setting CN2, Floppy Disk Drive CN1, Primary IDE CN3, Secondary IDE CN4, Parallel Port CN12, Serial Port 9-pin D-sub (COM1) CN11, Serial Port 2x5 pin header (COM2) CN8, External Keyboard CN17, Mouse CN18, Keyboard/Mouse CN7, Multi Panel Switch C
Resumo do conteúdo contido na página número 11
JUMPERS The default settings are highlighted in the tables that follow. CPU Frequency Setting (JP3) Frequency 1-3 2-4 3-5 4-6 50 MHz OFF OFF ON ON 66 MHz/100 MHz* ON ON OFF OFF 75 MHz OFF ON ON OFF 83.3 MHz ON OFF OFF ON *Intel Celeron CPU will auto-detect 66 MHz. * Intel Pentium III (FC-PGA) CPU will auto detect 100MHz. *Refer to figure 2 for the location of JP3. CPU Multiplier Setting (JP8) Ration 1-2 3-4 5-6 7-8 3.0 x ON OFF ON ON 3.5 x ON OFF OFF ON 4.0 x OFF ON ON ON 4.5 x OFF ON OFF ON 5.0
Resumo do conteúdo contido na página número 12
Watchdog Timeout Period (JP12) Period 1-2 3-4 5-6 7-8 1 sec. OFF OFF ON OFF 2 sec. OFF OFF ON ON 10 sec. OFF ON OFF OFF 20 sec. OFF ON OFF ON 110 sec. ON OFF OFF OFF 220 sec. ON OFF OFF ON Refer to figure 2 for the location of JP12. DiskOnChip™ Memory Address Setting (JP11) The DiskOnChip™ (DOC) Flash Disk Chip is produced by M-Systems. No extra soft - ware utility is needed because the DOC is 100% compatible to hard disk. It is "plug and play", easy, and reliable. The DOC is available from 2 MB
Resumo do conteúdo contido na página número 13
PS/2 Mouse Setting (JP7) The PS/2 mouse uses IRQ12 while in operation. JP7 Description ON Enable the PS/2 Mouse, IRQ12 OFF Disable the PS/2 Mouse Refer to figure 2 for the location of JP7. 15 Board Configuration
Resumo do conteúdo contido na página número 14
CONNECTORS This section describes how to connect peripherals, switches, and indicators to the SBC-370. Floppy Disk Drive Connector (CN2) The SBC-370 is equipped with a 34-pin daisy-chain drive connector cable. For the location of this connector, refer to CN2 in figure 2. Pin Number Description Pin Number Description 1 GND 19 GND 2 REDUCE WRITE 20 STEP# 3 GND 21 GND 4NC 22 WRITE DATA# 5 GND 23 GND 6NC 24 WRITE GATE# 7 GND 25 GND 8 INDEX# 26 TRACK 0# 9 GND 27 GND 10 MOTOR ENABLE A# 28 WRITE PROTEC
Resumo do conteúdo contido na página número 15
PCI E-IDE Disk Drive Connector (CN1/CN3) You can attach four IDE (Integrated Device Electronics) hard disk drives to the SBC-370 IDE controller. CN1 (IDE 1): Primary IDE Connector CN3 (IDE 2): Secondary IDE Connector For the location of these connectors, refer to CN1 and CN3 in figure 2. Pin Number Description Pin Number Description 1 RESET# 21 IDE DRQ 2 GND 22 GND 3 DATA 7 23 IOW# 4 DATA 8 24 GND 5 DATA 6 25 IOR# 6 DATA 9 26 GND 7 DATA 5 27 IDE CHRDY 8 DATA 10 28 GND 9 DATA 4 29 IDE DACK 10
Resumo do conteúdo contido na página número 16
Parallel Port (CN4) This port is usually connected to a printer. The SBC-370 includes an onboard par- allel port accessed through a 26-pin flat-cable connector. For the location of this connector, refer to CN4 in figure 2. Pin Number Description 1 STROBE# 2 DATA 0 3 DATA 1 4 DATA 2 5 DATA 3 6 DATA 4 7 DATA 5 8 DATA 6 9 DATA 7 10 ACKNOWLEDGE 11 BUSY 12 PAPER EMPTY 13 PRINTER SELECT 14 AUTO FORM FEED # 15 ERROR# 16 INITIALIZE 17 PRINTER SELECT LN# 18 GND 19 GND 20 GND 21 GND 22 GND 23 GND 24 GND 2
Resumo do conteúdo contido na página número 17
Serial Ports (CN12/CN11) The SBC-370 offers two high speed NS16C550 compatible UARTs with Read/Re- ceive 16 byte FIFO serial ports (COM1/COM2). CN12: Serial Port 9-pin D-sub Connector (COM1) Pin Number Description 1 DCD 2RXD 3 TXD 4 DTR 5 GND 6 DSR 7RTS 8 CTS 9RI CN11: Serial Port 2x5 pin header Connector (COM2) Pin Number Description 1 DCD 2 DSR 3RXD 4RTS 5 TXD 6 CTX 7 DTR 8RI 9 GND 10 NC For the location of these connectors, refer to CN12 and CN11 in figure 2. 19 Board Configuration
Resumo do conteúdo contido na página número 18
Keyboard/Mouse Connector (CN8/CN17/CN18) The SBC-370 provides one external keyboard, one external mouse, and one PS/2 keyboard and mouse connector. CN8: 5-pin Header External Keyboard Connector (see note below) Pin Number Description 1 KB CLK 2 KB DATA 3NC 4 GND 5 +5V CN17: PS/2 Mouse 5-pin Header Connector Pin Number Description 1 MS DATA 2NC 3 GND 4 +5V 5MSCLK CN18: 6-pin Mini-DIN PS/2 Keyboard and Mouse Connector (see note below) Pin Number Description 1 KB DATA 2NC 3 GND 4 +5V 5 KB CLK
Resumo do conteúdo contido na página número 19
External Switches and Indicators (CN7) There are several external switches and indicators for monitoring and controlling the CPU board. All the functions are in the CN7 Multi Panel connector. For the lo - cation of this connector, refer to figure 2. Pin Number Description Pin Number Description 1 SPEAKER 11 GND 2 VCC 12 GND 3NC 13 IDE LED 4NC 14 NC 5NC 15 +5V 6 GND 16 ATX POWER CONTROL 7 +5V 17 ATX POWER BUTTON 8 KEYLOCK 18 ATX 5VSB 9 RESET SW 19 ATX 5VSB 10 GND 20 ATX 5VSB USB Port Connector (C
Resumo do conteúdo contido na página número 20
IrDA Infrared Interface Port (CN6) The built-in IrDA port supports Serial Infrared (SIR) or Amplitude Shift Keyed IR (ASKIR) interface. To use the IrDA port, configure the SIR or ASKIR model in the BIOS's Peripheral Setup's COM2. Then, the normal RS-232 COM2 will be disabled. For the location of this connector, refer to figure 2. Pin Number Description 1 VCC 2 FIR-RX 3 IR-RX 4 GND 5IR-TX 6 CIR-RX VGA Connector (J1) The built-in 15-pin VGA connector can be connected directly to your monochrome CR
