Resumo do conteúdo contido na página número 1
INSTALLATION GUIDE
Agilent Technologies
MPS Mainframe
Model 66000A
SERIAL NUMBERS
For mainframe with serial numbers:
Agilent Model 66000A: 3138A-00101 and above
* For instruments with higher Serial Numbers, a change page may be included.
Agilent Part No. 66000-90001 Printed in USA: June , 1997
Microfiche Part No. 66000-90002 Update April 2000
Resumo do conteúdo contido na página número 2
CERTIFICATION Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Bureau of Standards, to the extent allowed by the Bureau’s calibration facility, and to the calibration facilities of other International Standards Organization members. WARRANTY This Agilent Technologies hardware product is warranted against defect
Resumo do conteúdo contido na página número 3
SAFETY SUMMARY The following general safety precautions must be observed during all phases of operation, service, and repair of this mainframe. Failure to comply with these precautions or with specific warnings elsewhere in this guide violates safety standards of design, manufacture, and intended use of the mainframe. Agilent Technologies assumes no liability for the customer’s failure to comply with these requirements. BEFORE APPLYING POWER. Verify that the product is set to match the available
Resumo do conteúdo contido na página número 4
SAFETY SUMMARY (continued) GENERAL: Any LEDs used in this product are Class 1 LEDs as per IEC 825-1. ENVIRONMENTAL CONDITIONS: This instrument is intended for indoor use in an installation category II, pollution degree 2 environment. It is designed to operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer to the specifications tables for the ac mains voltage requirements and ambient operating temperature range. SAFETY SYMBOL DEFINITIONS Symbol Description Symb
Resumo do conteúdo contido na página número 5
DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Agilent Technologies, Inc. Manufacturer's Address: 140 Green Pond Road Rockaway, New Jersey 07866 U.S.A. declares that the Product Product Name: Modular Power System mainframe and modules Model Number: Agilent 66000A mainframe and modules Agilent 66101A, 66102A, 66103A, 66104A, 66105A, 66106A conforms to the following Product Specifications: 1 Safety: IEC 348:1978 / HD 401S1: 1981 EMC: CISPR 11:1990 / EN 5
Resumo do conteúdo contido na página número 6
Table Of Contents 1. General Information Introduction ..................................................................................................................................................9 Safety Considerations...................................................................................................................................9 Instrument Identification .............................................................................................................
Resumo do conteúdo contido na página número 7
Figures 2-1. Power Cord Plug Configurations............................................................................................14 2-2. Power Cord Installation..........................................................................................................15 2-3. Rear Panel Switches ...............................................................................................................16 2-4. Switch Settings .................................................................
Resumo do conteúdo contido na página número 8
1 General Information Introduction This guide describes how to install the Agilent 66000A Modular Power System (MPS) Mainframe. It includes the following information: ■ specifications and operating characteristics ■ connecting the power cord to the mainframe ■ setting the address and frame switches ■ installing modules in the mainframe ■ mainframe rear panel connections Mainframe turn-on and checkout procedures are included with the module manual since an installed module is required to prop
Resumo do conteúdo contido na página número 9
Options and Parts The following options are available with the mainframe: Option Description 908 Rack Mounting Kit 909 Rack Mounting Kit with handles 910 Extra Manual Set Power Cords 831 12 AWG unterminated power cord 2 833 1.5 mm unterminated power cord 834 10 AWG unterminated power cord 841 20 A/250 V NEMA 6-20P plug with 12 AWG power cord 843 20 A/250 V JIS C8303 plug with 12 AWG power cord 2 845 16 A/220 V IEC 309 plug with 1.5 mm power cord 846 30 A/120 V L5-30P locki
Resumo do conteúdo contido na página número 10
Specifications and Supplemental Characteristics Table 1-1 lists the specifications and supplemental characteristics of the MPS mainframe. Module specifications are included in the appropriate module User’s Guide. Specifications are warranted in the temperature range of 0 to 55 degrees C. Supplemental characteristics are not warranted, but are descriptions of minimum, maximum, or average performance that has been determined by design or type testing. Table 1-1. Specifications and Supple
Resumo do conteúdo contido na página número 11
Table 1-1. Specifications and Supplemental Characteristics (continued) INH/FLT Characteristics Maximum Ratings: ± 16.5 V between pins 3 and 4 + 16.5 V between pins 1 and 2 - 5.3 V between pins 1 and 2 INH (10k pull-up): I @ 4 V = 700 μA IL I @ 5.25 V = 200 μA IH V = 0.8 V maximum IL V = 2.0 V minimum IH DFI (open collector): V = 0.4 V maximum @ IC = 2.2 mA CE I @ 5.25 V = 200 μA IH V = 0.8 V maximum IL V = 2.0 V minimum IH Dimensions Width: 426 mm (16.75
Resumo do conteúdo contido na página número 12
2 Installation Installation When you receive your mainframe, first look for any obvious damage that could have occurred during shipment. If there is damage, notify the carrier and the nearest Agilent Sales Office immediately. Warranty information is printed behind the cover page of this manual. Save the shipping carton and packing materials in case the mainframe has to be returned to Agilent Technologies in the future. If you return the mainframe for service, attach a tag ident
Resumo do conteúdo contido na página número 13
Fuses The mainframe fuse is located inside the mainframe. Refer to the mainframe Service Manual for information about replacing the fuse. Power Cord Installation The power cord supplied with your mainframe may or may not include a power plug. Figure 2-1 shows the various power plugs. Ring terminals are attached to one end of the power cord to facilitate mainframe installation. Figure 2-1. Power Cord Plug Configurations If your power cord will be directly wired into your loc
Resumo do conteúdo contido na página número 14
Figure 2-2. Power Cord Installation Location and Cooling Bench Operation Chapter 1 gives the dimensions of your mainframe. The mainframe has plastic feet that are shaped to ensure self-alignment when stacked with other Agilent System II cabinets. The feet may be removed for rack mounting. Your mainframe must be installed in a location that allows sufficient space at the sides and rear of the mainframe for adequate air circulation. Do not block the vents at the sides and rear of
Resumo do conteúdo contido na página número 15
Rear Panel Switches The six-position rear panel switch is shown in the following figure. Figure 2-3. Rear Panel Switches Address Switches Address switches A0 through A4 set the primary GPIB address. The address is set in binary, A0 being the least significant bit and A4 being the most significant bit. Figure 2-3 shows the factory-set address of "5" (binary 00101). Any address from decimal 0 to decimal 30 is a valid GPIB address. Refer to the following diagram for switch setti
Resumo do conteúdo contido na página número 16
Mainframe Slot Locations/Addresses Mainframe Mode Mainframe Mode Switch = MAIN Switch = AUX Slot Location 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 Secondary Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Note Secondary addresses are reserved for the mainframe whether modules occupy the associated slot locations or not. You may want to apply stick-on labels over the slot locations of the mainframe to indicate that the modules installed in the auxiliary mainframe are at secondary addresse
Resumo do conteúdo contido na página número 17
Module Installation Note A fully loaded mainframe can weigh over 36 kg (80 lbs). Install the mainframe into the rack before installing the modules into the mainframe. All modules install through the front of the mainframe. Installation (and removal) can be accomplished even when the mainframe is rack-mounted. To install the modules in the mainframe, refer to Figure 2-5 and proceed as follows: ■ Use a flat-bladed screwdriver and release the pull tab by pressing down. ■ Extend the
Resumo do conteúdo contido na página número 18
■ There must be no or minimal current flowing through the connector pins at the back of the module that is being removed. This can be accomplished by disabling the module. If this precaution is repeatedly violated at high current, the connector pins at the back of the module will be damaged. ■ There must be no activity on the GPIB bus, the trigger connectors, or the FLT/INH connector of the mainframe when a module is removed. This can be accomplished by not generating any GPI
Resumo do conteúdo contido na página número 19
3 Connections Rear Panel Figure 3-1 shows where all of the rear panel connections to the mainframe are made. Figure 3-1. Rear Panel Connections Module Connections Wire connections to the modules are made using a separate module connector that is supplied with each module. After the module connector has been wired, it simply attaches to the back of the mainframe. You can attach the module connector to the mainframe either before or after the module is installed.
Resumo do conteúdo contido na página número 20
Controller Connections If you have only one MPS mainframe in your system, simply connect it to the controller using the GPIB cable. If you have more than one mainframe, or if you also have an Agilent 667xA, 665xA, 664xA, or 603xA power supply in your system, you can use the serial-link cable supplied with your mainframe to facilitate connections. Figure 3-2 illustrates the serial-link connections. Multiple MPS Mainframes See Figure 3-2. Up to 16 modules may be controlled from a
