Resumo do conteúdo contido na página número 1
Product Manual
SV35.4 Series SATA
ST3320410SV
100520771
Rev. B
July 2008
Resumo do conteúdo contido na página número 2
Revision history Revision Date Sheets affected or comments Rev. A 06/16/08 Initial release. Rev. B 07/24/08 4, 7, 23 and 24. Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100520771, Rev. B July 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. SV35.4 Series, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technolog
Resumo do conteúdo contido na página número 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary tables . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 4
ii SV35.4 Series SATA Product Manual, Rev. B
Resumo do conteúdo contido na página número 5
List of Figures Figure 1. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Figure 4. Mounting dimensions . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 6
Resumo do conteúdo contido na página número 7
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate TM SV35.4 Series model drive: ST3320410SV These drives provide the following key features: • High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second). • Perpendicular recording, Tunneling Magnetoresistive (TMR) recording heads and EPRML technology, for increased areal density. • State-of-the-art cache and on-the-fly error-correction algorithms. • Native
Resumo do conteúdo contido na página número 8
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump- ers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels. In addition, Serial ATA makes the transition f
Resumo do conteúdo contido na página número 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive model: ST3320410SV 2.1 Specification summary tables The specifications listed in the following tables are for quick reference. For details on specification measure- ment or definition, see the appropriate section of this manual. SV35.4 Series S
Resumo do conteúdo contido na página número 10
Table 1: Drive specifications summary for 320 Gbyte models Drive specification ST3320410SV Formatted capacity 320 Gbytes (512 bytes/sector)* Guaranteed sectors 625,142,448 Heads 2 Discs 1 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 1,242 kbits/in max Track density 173 ktracks/in avg 2 Areal density 215 Gbits/in avg Internal data transfer rate 1,201 Mbits/sec max Sustained data transfer rate 90 Mbytes/sec max I/O data-t
Resumo do conteúdo contido na página número 11
Drive specification ST3320410SV Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs Vibration, nonoperating 5–350 Hz: 5.0 Gs 350–500 Hz:: 1.0 Gs Drive acoustics, sound power Idle** 1.9 bels (typical) 2.1 bels (max) CE Seek Profile 2.3 bels (typical) 2.4 bels (max) 14 Nonrecoverable read errors 1 per 10 bits read Annualized Failure Rate (AFR) 0.62% Warranty 5 years on distribution units. To determine the warranty for a specific drive
Resumo do conteúdo contido na página número 12
2.2 Formatted capacity Formatted Guaranteed Model capacity* sectors Bytes per sector ST3320410SV 320 Gbytes 625,142,448 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1 LBA mode When addressing the drive in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.3.1, "Identify Device
Resumo do conteúdo contido na página número 13
2.5 Physical characteristics 320GB model Maximum height 20.20 mm (0.794 inches) Maximum width 101.85 mm (4.010 inches) Maximum length 146.99 mm (5.787 inches) Typical weight 380 grams (0.838 lb.) Cache buffer 16 Mbytes (16,384 kbytes) 2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible singl
Resumo do conteúdo contido na página número 14
2.8 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 3 on page 18. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operat
Resumo do conteúdo contido na página número 15
2.8.1.1 Typical current profiles Figure 1. Typical 12V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz. • Using 5-volt power, the drive is expected to operate wi
Resumo do conteúdo contido na página número 16
2.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Power modes Heads Spindle Buffer Active Tracking Rotating Enabled Idle Tracking Rotating Enabled Standby Parked Stopped Enabled Sleep Parked Stopped Disabled • Active mode The drive is in Active mode during the read/write and seek operation
Resumo do conteúdo contido na página número 17
2.9 Environmental specifications 2.9.1 Drive case temperature Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters). Drive case temperature should be measured at the location indicated in Figure 4 on page 19. Operating (Drive case temperature) 0° to 75°C (32° to 167°F) Nonoperating (Ambient *) –40° to 70°C (–40° to 158°F) * Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. 2
Resumo do conteúdo contido na página número 18
2.9.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock The drives comply with the performance levels specified in this document when subjected to a maximum oper- ating shock of 70 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.9.5.2 Nonoperating shock The nonoperating shock level tha
Resumo do conteúdo contido na página número 19
2.10 Acoustics emissions Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25 degrees C). Emission levels are reported as the total A-weighted sound power levels for, steady state, idle and active (seek) modes of operations. Table 3: Drive A-weighted Sound Power Levels (SWL, BA) Idle[1] CE seek profile 1.9 bels (typ) 2.3 bels (typ) 320 GB model 2.1 bels (max) 2.4 bels (max) [1] During periods o
Resumo do conteúdo contido na página número 20
2.12 Reliability 2.12.1 Annualized Failure Rate (AFR) The product shall achieve an Annualized Failure Rate (AFR) of 0.62% when operated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifications in Section 2.9 may increase the product AFR. AFR is a population statistics that is not relevant to individual units. AFR specifications are based on the following assumptions for desktop personal computer environments: • 8760 power-on-hours per year. •
