Manual do usuário Toshiba SD-M1201

Resumo do conteúdo contido na página número 1

SD-M1201 DVD-ROM
with REALmagic Hollywood+ Playback Card
Installation Instructions
Congratulations on your purchase of a Toshiba SD-M1201 DVD-ROM
drive and REALmagic Hollywood+ DVD/MPEG-2 Playback Card Kit.
The following information will help you in the simple installation of
your new DVD-ROM. It is assumed that you are replacing a presently
installed CD-ROM with the enclosed DVD-ROM. If this is not the case,
additional installation hardware may be required. Refer to REALmagic
Hollywood+ User’

Resumo do conteúdo contido na página número 2

The follow steps must be performed to properly install your DVD-ROM. l Set DVD-ROM drive jumper settings. l Connect audio cable. l Install SCSI host adapter board. l Attach SCSI interface cable. l Mount DVD-ROM. SETTING JUMPERS The block of mode select jumpers are located on the rear of the DVD- ROM. If the jumper covers both pins on the jumper block, it is ON; if there is no jumper or only one of the pins is covered, the jumper is OFF. The jumper settings include SCSI ID, Parity, Termination,

Resumo do conteúdo contido na página número 3

PRV/ALW - This jumper is used to inhibit the drive’s EJECT button. When the jumper is ON, the EJECT button will not operate. Test - This setting selects the drive operation between normal CD-ROM and CD-Audio player mode. When jumper is set to ON position, com- mands from the host computer are ignored. This jumper is for test pur- poses only and should be set to OFF for proper CD-ROM function. Power Supply - Toshiba SCSI DVD-ROM drives can supply power to other equipment on the SCSI BUS. When

Resumo do conteúdo contido na página número 4

If you are replacing your CD-ROM: connect DVD-ROM to the SCSI interface connector that the CD-ROM was connected to. If DVD-ROM is not replacing a CD-ROM or is an addition to a CD-ROM: daisy-chain the DVD-ROM drive with a custom built SCSI interface cable (not supplied with kit). See Daisy-Chaining Section on page 5 for more information. Power Cable - Connect an internal computer power supply cable to the power socket at the back of the DVD-ROM. One side of the plug has chamfered edges, so the

Resumo do conteúdo contido na página número 5

Daisy-Chaining - If the DVD-ROM you are installing is one of two or more SCSI devices you are connecting to your system, you will need to use a custom built SCSI interface cable. Remember that the terminator jumper on the DVD-ROM drive must have the jumper installed when the drive is the last device in the chain. Host Computer Interface I/F Card Connector SCSI Cable DVD-ROM DRIVE (see note 1) Terminator SD-M1201 CONNECTION (ONE DRIVE) SD-M1201 INTERNAL DRIVE(S) Host Computer SCSI Cable Interfa

Resumo do conteúdo contido na página número 6

COMPLETING INSTALLATION After you have connected all the necessary cables, push the DVD-ROM completely into the computer’s drive slot. Mount drive accord- Mounting Screw ing to your computer’s instruc- M3 tions. The screw length should Mounting frame of not exceed 3±0.5mm (measured host computer from outside surface of side or Surface of side or bottom bottom of DVD-ROM to tip of of DVD-ROM drive screw). Replace computer cover and all outer screws. 2.5 - 3.5mm Software Driver: The T

Resumo do conteúdo contido na página número 7

DVD-ROM BACK PANEL The photo illustrates the following features of the SD-M1202 DVD-ROM back panel: ① Analog audio out connector ② Mode select jumper ③ SCSI interface connector ④ Power connector 7

Resumo do conteúdo contido na página número 8

TECHNICAL SUPPORT Technical support can be obtained by calling 949/455-0407. Drivers are available on BBS at 949/837-8864 or on our web site at http://www.toshiba.com SD-M1201 SPECIFICATIONS DVD CD-ROM Data Capacity (bytes/block) 2,048 mode 1 mode 2 2,048 2,336 Rotational Speed (approx. rpm) 2,900 13.8 ~ 32X: 6,900 8.6 ~ 20X: 4,300 (CD-RW) 4 ~ 5.7X: 1,200-2,000 (audio) Sustained Data Transfer Rate 2,797 ~ mode 1 mode 2 (kbytes/sec) 6,760 2,069 ~ 2,360 ~ 4,800 5,475 Access Time (Typ.) Avg. Rando