Resumo do conteúdo contido na página número 1
Serial ATA 4-Channel PCI
Quick Installation Guide
Introducing the Serial ATA 4-Channel PCI
The Serial ATA 4-Channel PCI is an ultra high-speed four
channel Serial ATA controller for use in Pentium-class
computers. It achieves burst data transfer rates up to
150MB/s (1.5Gb/s) and supports various brand of hard
disk drives with capacities greater that 137GB.
Features and Benefits
• Compliant with Serial ATA Specification, rev 1.0
Compliant with PCI Specification, revision 2.2
Provides four in
Resumo do conteúdo contido na página número 2
Package Contents (1) Serial ATA 4-Channel PCI board (1) Driver CD (2) Serial ATA cable (1) Dual connector Serial ATA power cable This quick installation guide Board Layout Hard Disk Serial ATA LED Pins Connectors CN4 CN3 CN2 CN1 Figure 1. Serial ATA 4-Channel PCI Layout Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if ne
Resumo do conteúdo contido na página número 3
Remove your computer’s cover and install the card in an available PCI slot. Push the board down firmly, but gently, until it is well seated. Install a slot bracket holding screw to secure the card. Now go to Device Connection to connect your Serial ATA hard disk drive(s). Device Connection If you plan to use more than two Serial ATA channels, you will need to purchase additional Serial ATA data and power cables. 1. Install hard disk drive(s) into chassis. 2. Connect the Serial ATA hard di
Resumo do conteúdo contido na página número 4
Note: If you like to monitor disk activity of the Serial ATA hard drives, you may at this time connect the hard disk LED of the system case to the Hard Disk LED Pins on the Serial ATA controller, see figure 1, on page 2 for the location of the pins. For most systems connect the red wire to the pin farthest from the mounting bracket. 6. Replace the computer cover and reconnect the power cord. Go to Software Installation to install the Serial ATA 4-Channel PCI device driver. Software Installa
Resumo do conteúdo contido na página número 5
5. Insert the driver CD and click Next. 6. Select Search for a better driver ... and click Next. 7. Check CD-ROM drive, uncheck the other boxes, then click Next. Click Next again, then Finish. 8. Click Yes to restart Windows to complete the driver installation. For Existing Windows 98 Installation 1. Install the board and boot up Windows 98. 2. At the Add New Hardware Wizard, click Next. 3. Select Search for the best driver for your device and click Next. 4. Insert the driver CD, check CD-ROM d
Resumo do conteúdo contido na página número 6
7. Click Finish, then click Yes to restart Windows to complete the driver installation. For Existing Windows ME Installation 1. Install the board and boot up Windows ME. 2. At the Add New Hardware Wizard, insert the driver CD. 3. Select Automatic search for a better driver (Recommended), then click Next. 4. Accept the selected driver, then click OK. 5. Click Finish, then restart Windows to complete the driver installation. Verify Proper Installation for Windows 98/ME 1. Right-click My Computer,
Resumo do conteúdo contido na página número 7
2. At the Windows NT Setup screen, press F6 to specify and add the driver. 3. Press S, select Other, then press Enter. 4. Insert the driver diskette and press Enter. 5. Select Silicon Image SiI 3114 ... Controller for Windows NT 4.0 and 2000, and press Enter. 6. Press Enter to continue and follow on-screen instructions to complete Windows NT4.0 installation. For Existing Windows NT4.0 Installation 1. Install the board and boot up Windows NT4.0. 2. Double click My Computer/Control Panel/SCSI Adap
Resumo do conteúdo contido na página número 8
Windows 2000 Driver Installation A new installation of Windows 2000 requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the Floppy folder, found on the driver CD, onto a blank floppy disk then follow the directions below. For New Windows 2000 Installation 1. Install the board and follow Microsoft procedures to install Windows 2000 accordingly. 2. Restart your system when prompted during Windows' installation. 3. At the Windows 2000 Setup screen, pr
Resumo do conteúdo contido na página número 9
Windows XP/Server 2003 Driver Installation A new installation of Windows XP/Server 2003 requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the Floppy folder, found on the driver CD, onto a blank floppy disk then follow the directions below. For New Windows XP/Server 2003 Installation 1. Install the board and follow Microsoft procedures to install Windows accordingly. 2. Restart your system when prompted by Windows' installation. 3. At the Windows
Resumo do conteúdo contido na página número 10
Note: If a warning message pops up, click Continue Anyway, then click Finish. Our driver has been thoroughly tested in Windows for stability. 4. Remove the driver CD and restart Windows to complete the driver installation. Verify Proper Installation for Windows 2000/XP/ Server 2003 1. Right click My Computer and click Manage. 2. Select Device Manager. 3. Double click SCSI and RAID controllers, then double click Silicon Image SiI 3114 ... Controller to display driver properties. 4. A message Th
Resumo do conteúdo contido na página número 11
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. A lifetime manufacturer warranty supplied with this product is offered by SIIG, Inc. Please see SIIG website for more
Resumo do conteúdo contido na página número 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by
