Resumo do conteúdo contido na página número 1
Product Manual
Momentus 5400.5 SATA
ST9320320AS
ST9250320AS
ST9200321AS
ST9160310AS
ST9160310ASG
ST9120310AS
ST9120310ASG
ST980310AS
ST980310ASG
100468844
Rev. B
July 2008
Resumo do conteúdo contido na página número 2
Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100468844, Rev. B July 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademar
Resumo do conteúdo contido na página número 3
Momentus 5400.5 SATA Product Manual, Rev. B i
Resumo do conteúdo contido na página número 4
ii Momentus 5400.5 SATA Product Manual, Rev. B
Resumo do conteúdo contido na página número 5
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 6
iv Momentus 5400.5 SATA Product Manual, Rev. B
Resumo do conteúdo contido na página número 7
List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . .
Resumo do conteúdo contido na página número 8
Resumo do conteúdo contido na página número 9
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.5 SATA model drives: � ST9320320AS � ST9250320AS � ST9200321AS � ST9160310AS � ST9160310ASG � ST9120310AS � ST9120310ASG � ST980310AS � ST980310ASG These drives provide the following key features: � 5,400-RPM spindle speed. � 8-Mbyte buffer. � Free Fall Protection (on ST9160310ASG, ST9120310ASG and ST980310ASG models only) � Quiet operation. Fluid Dynamic Bear
Resumo do conteúdo contido na página número 10
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: � Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration options. � Thinner and more flexible cabling for improved enclosure airflow and ease of installation. � Scalability to higher performance levels. In addition, Serial ATA makes the tran
Resumo do conteúdo contido na página número 11
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST9320320AS, ST9250320AS, ST9200321AS, ST9160310AS, ST9160310ASG, ST9120310AS, ST9120310ASG, ST980310AS and ST980310ASG models. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measur
Resumo do conteúdo contido na página número 12
Table 1: Drive specifications ST9160310AS ST9120310AS ST980310AS Drive specification ST9320320AS ST9250320AS ST9200321AS ST9160310ASG ST9120310ASG ST980310ASG Track-to-track seek time, read 1 (msec typical) Average seek, read (msec typical) 14 Full-stroke seek, read (msec) 24 (typical) Startup current, +5V (max) 1.0 amps Seek power (typical) 1.54 watts Read/write power (typical) Read: 2.6 watts; Write: 2.85 watts Idle mode, low power (typical) 0.725 watts Standby mode 0.22 watts (typical)*** S
Resumo do conteúdo contido na página número 13
Table 1: Drive specifications ST9160310AS ST9120310AS ST980310AS Drive specification ST9320320AS ST9250320AS ST9200321AS ST9160310ASG ST9120310ASG ST980310ASG Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase
Resumo do conteúdo contido na página número 14
2.4 Physical organization Drive model Read/write heads Number of discs ST9320320AS 4 2 ST9250320AS 4 or 3 2 ST9200321AS 3 2 ST9160310AS and ST9160310ASG 2 1 ST9120310AS and ST9120310ASG 2 1 ST980310AS and ST980310ASG 1 1 2.5 Recording and interface technology Interface Serial ATA (SATA) Recording method Perpendicular Recording density BPI (bits/inch avg) 1,337k Track density TPI (tracks/inch avg) 190k 2 Areal density (Gbits/inch avg) 254 Spindle speed (RPM) (± 0.2%) 5,400 Maximum Internal tra
Resumo do conteúdo contido na página número 15
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Table 2: Typical seek times Typical seek times (msec) Read Track-t
Resumo do conteúdo contido na página número 16
2.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/write actuator arm
Resumo do conteúdo contido na página número 17
2.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 2.9.2 Deferred spinup Momentus 5400.5 SATA drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives. 2.9.3 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maxim
Resumo do conteúdo contido na página número 18
2.9.5 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 4: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power
Resumo do conteúdo contido na página número 19
Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating: 0° to 60°C (32° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour (68°F per hour max), without condensation Nonoperating 35°C per hour (95°F per hour max), without condensation 2.10.3 Humidity 2.10.3.1 Relative humidity Operating 5% to 95% noncondensing (30% per hour max) Nonoperating 5% to 95% noncondensing (30% per hour max) 2.10
Resumo do conteúdo contido na página número 20
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. Note. Additional shock protection is provided by the Free Fall Protection feature on ST9160310ASG, ST9120310ASG and ST980310ASG models. See Section 2.13.1 for additional information about this feature. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subject
