Resumo do conteúdo contido na página número 1
Serial ATA to Serial ATA
Model: MRK-300ST-BK
Aluminum Mobile Rack 3-1
Resumo do conteúdo contido na página número 2
3-1 Introduction ........................................................................ 3-3 Mobile Rack Features ................................................... 3-3 Unpacking Your Mobile Rack ........................................ 3-4 IDE Basics .................................................................... 3-4 3-2 Hardware Installation.......................................................... 3-5 Mobile Rack Components ............................................. 3-5 Installing t
Resumo do conteúdo contido na página número 3
3 - 1 I n t r o d u c t i o n The EZ-Swap 2 Serial ATA version is as convenient as mobile racks get. The EZ-Swap 2 SATA features the ability to directly connect your SATA hard drive without going through any additional circuits. Simply place the hard drive inside the cartridge, screw it in place, and your done. The EZ-Swap 2 SATA also features keyed lock protection to prevent removal while in use. Since it uses SATA technology, the EZ-Swap 2 SATA is also hot swappable. Easy, convenient
Resumo do conteúdo contido na página número 4
Unpacking Your Mobile Rack Before installing the Mobile Rack, verify that the following items are included in the carton. If any parts are damaged or missing, please contact your local dealer or sales representative immediately. 1.One Mobile Rack Removable Docking Module 2.Twelve (12) mounting screws 3.2 keys 4.One user’s guide SATA Basics Serial ATA (SATA) is the latest interface standard used for hard drives, optical drives (CD/DVD Rom drives), and other computer devices. Because it uses ser
Resumo do conteúdo contido na página número 5
3-2 Hardware Installation The Aluminum Mobile Rack Docking Module is designed to install in any PC/AT or Pentium-class computer that has an available 5.25-inch half-height drive bay. General instructions for installing the Mobile Rack are given since the design of computer cases varies. Refer to your computer’s manual whenever in doubt. Mobile Rack Components The Mobile Rack is comprised of two components: Docking Case Drive Case Mounting Holes Key-Lock/Power Switch Power ON/OFF Drive Activity
Resumo do conteúdo contido na página número 6
Installing the Mobile Rack Docking Case 1. Turn OFF the power to your computer and any other connected peripheral devices. Follow the precautions for static electricity discharge: • Discharge any static electricity build up in your body by touching a grounded metal surface such as the computer case, if plugged in. • During installation procedures, avoid any contact with internal parts. 2. Unplug the power cord from the back of the computer. 3. Remove your computer’s cover. 4. Remove the compute
Resumo do conteúdo contido na página número 7
7. Position the docking case so its mounting holes align with the drive bay’s mounting holes. Secure with the supplied mounting screws (two/four on each side.) 8. Attach the red SATA cable from the back of the unit to an available SATA port on the system board or anySATA controller card. Connect the red and white HDD Access/Activity signal cable to the HDD signal pins on your system board. 9. Connect an available 4-pin power cable from the system’s power supply to the 4-pin connector on the ba
Resumo do conteúdo contido na página número 8
2. Carefully position the drive inside the drive case. 3. Secure the drive in place using the supplied mounting screws. Use the mounting holes on the sides or bottom, depending on the design of the drive. Mounting Screws Mounting Screws Install the Drive in Drive Case 4. Slide the drive case cover back on and secure with the two mounting screws. Slide Cover On Mounting Screws (x2) Mobile Rack Drive Case Ready for Use 3-8 Aluminum Mobile Rack
Resumo do conteúdo contido na página número 9
3-3 Using the Mobile Rack WARNING •DO NOT remove the drive case while the drive is working. Damage to data may result. •The Key-Lock must be in the Lock position while in use. To insert the Mobile Rack drive case: 1.Insert the Mobile Rack drive case (with drive installed) into the installed Mobile Rack docking case and push firmly until the drive is seated. 2.Insert the key and turn it r i g h t to lock. The LED on the Mobile Rack should light after a slight delay. The installed Mobile Rack devi
Resumo do conteúdo contido na página número 10
3-4 Troubleshooting Q. I installed the EZ-Swap 2 but my computer does not detect the hard drive in it. A. Be sure to turn on the EZ-Swap 2 by setting the Key-Lock in the Lock position. The EZ-Swap 2 will not turn on unless it is locked. If you are using a brand new drive, make sure you initialize, partition and format the drive before trying to use it. This can be done using the software that comes with the HARD DRIVE or by using Windows’ Disk Management utility. Q. The data on my hard driv
