Manual do usuário Field Controls UV-18

Resumo do conteúdo contido na página número 1

UV-AIRE™ AIR PURIFYING SYSTEM
Model: UV-12,18
ITEMS INCLUDED IN KIT:
1-UV-Aire ™ power unit
4-Sheet metal mounting screws
1-Angled mounting bracket
1-Flat mounting bracket
1-Duct board mounting bracket
1-Ultra Violet lamp
1-Instruction Sheet
1-Wing nut
Caution Labels
Gasket
UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a
homes’ heating and air conditioning system. The treatment is a safe, silent, and proven way
to make your home a

Resumo do conteúdo contido na página número 2

I. INDICATION FOR USE This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention of any disease or condition. II. GENERAL INFORMATION There are different size units available, depending on the square footage of your home. See chart below for determining your homes needs. Minimum Max Air Lamp Intensity at 1 Recommended Model Duct Volts Amps Watts Hz Temp °F meter Max Sq. Feet

Resumo do conteúdo contido na página número 3

2. Determine the type of duct you have. (For flex duct applications, refer to Figure 21 on page 8) IF YOU HAVE METAL DUCT: a. Apply supplied wet and stick mounting template to air duct in either a vertical or horizontal position as shown in Figure 2. b. Drill 1/8” diameter mounting holes at positions indicated on template. c. Cut out the marked openings on template using a hole saw or a pair of tin snips or jigsaw. (See Figure 2) d. Remove paper template from duct. IF YOU HAVE DUCT BO

Resumo do conteúdo contido na página número 4

3. Remove base unit and cover from box. 4. Apply supplied “Duct Seal Kit” according to instructions included in kit (See Figure 12) Figure 12 5. Determine whether to use flat or angled bracket. (Refer to UV-Aire “Bulb Mounting Bracket Selection” in section IV for aid in this decision) a. Flat Bracket Installation i. Remove the two hex nuts and flat bracket from included bagged hardware. ii. Install the flat bracket and secure to the unit base with the hex nuts provided. (See Figure 13)

Resumo do conteúdo contido na página número 5

8. Insert lamp through hole until lamp cannot be inserted any further. (See Figure 16) Figure 16 9. Swing the swivel bracket over end of lamp. Hand-tighten the wing nut on stud. (See Figure 17) Be careful not to over tighten the wing nut. The porcelain at the lamp base may crack when over tightened. Figure 17 10. Plug ballast plug into end of lamp. (See Figure 18) 11. Snap cover onto the unit base. Close the cover and tighten cover screw. (See Figure 18 Figure 19 & 20) 12. Plug the

Resumo do conteúdo contido na página número 6

IV. BULB MOUNTING BRACKET SELECTION TM The UV-AIRE units come with an angled mounting bracket and flat mounting bracket to position the bulb either straight or at an angle. Choose one or the other bracket method best suited for your needs. Refer to the configurations chart below when making your selection. UV-Aire™ Configurations Good Best Standard 90° Patent Pending 45° Installation Installation (Flat Bracket) Single Lamp (16” Duct) (Angled Bracket) (16” Duct) ANGLED LAMP M

Resumo do conteúdo contido na página número 7

V. MAINTENANCE 1. Inspect and clean lamp at least every 6 months. 2. Replace your UV-Aire™ Air Purifying System lamp once a year to maintain the lamps maximum output intensity. The lamp should operate continuously for maximum lamp life and light effectiveness. VI. LAMP REPLACEMENT PROCEDURE VERY IMPORTANT: Turn switch on unit to ‘OFF’ position and unplug unit from outlet. 1. Loosen the cover screw on the side of the unit and open cover. 2. Unplug ballast plug from end of lamp. 3. Loosen

Resumo do conteúdo contido na página número 8

IX. FLEX DUCT INSTALLATION For installations on duct systems with a metallic main duct and flex duct branches, follow the instructions in figure 21 below. Figure 21 Limited Warranty Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and workmanship under normal use for eighteen (18) months from date of manufacturing by the consumer excepting the provisions numbered below. UV-LAMPS/BULBS Field Controls, L