Resumo do conteúdo contido na página número 1
500RTT
Owner's Manual
Resumo do conteúdo contido na página número 2
SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers Keep children and pets away. TRAINING Do not overload the machine capacity by attempting Read the Owner’s Manual care ful ly. Be thor ough ly to till too deep at too fast a rate. fa mil iar with the controls and the proper use of the equip ment. Know how to stop the unit and disengage Never operate the machine at high speeds on slippery the controls quickly. surfaces. Look behind and use care
Resumo do conteúdo contido na página número 3
CUSTOMER RESPONSIBILITIES PRODUCT SPECIFICATIONS Read and observe the safety rules. Gasoline Capacity: 2 Quarts Follow a regular schedule in maintaining, caring for Unleaded Reg u lar and using your tiller. Oil (API-SG-SL): SAE 30 (Above 40°F) Follow instructions under “Maintenance” and “Stor age” (Capacity 20 oz./0.6L) SAE 5W-30/10W30 (Below 40°F) sections of this Owner’s Manual. Spark
Resumo do conteúdo contido na página número 4
ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY FRONT A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) Utility knife (1) Tire pressure gauge (1) Pair of pliers LEFT RIGHT
Resumo do conteúdo contido na página número 5
ASSEMBLY UNPACKING CARTON (See Fig. 2) Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material. HANDLE ASSEMBLY "UP" POSITION IMPORTANT: WHEN UN PACK ING AND AS SEM BLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES. TIGHTEN HANDLE LOCK LEVER TO HOLD While holding handle assembly, cut cable ties se cur ing han
Resumo do conteúdo contido na página número 6
ASSEMBLY ATTACH CLUTCH CABLE (See Fig. 6) CONNECT SHIFT ROD (See Fig. 7) Insert end of shift rod into hole of shift lever indicator. Hook end of clutch cable through hole in control bar bracket. Insert hairpin clip through hole of shift rod to secure. SHIFT HAIRPIN CONTROL BAR SHIFT LEVER CLIP BRACKET ROD INDICATOR CONTROL BAR CLUTCH CABLE CONTROL BAR FIG. 7 BRACKET REMOVE TILLER FROM CRATE Make sure shift lever indicator is in “N” position (See Fig. 7) END OF CLUTCH
Resumo do conteúdo contido na página número 7
OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. SHIFT LEVER SHIFT LEVER IN DI CATO R DRIVE CONTROL BAR DEPTH STAKE LEVELING SHIELD RECOIL STARTER HANDLE OUTER SIDE
Resumo do conteúdo contido na página número 8
OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. DEPTH STAKE (See Fig. 10) HOW TO USE YOUR TILLER The depth stake can be raised or lowered to allow you more Know how to operate all controls before adding fuel and versatile tilling and cul
Resumo do conteúdo contido na página número 9
OPERATION TURNING Release the drive control bar. Move throttle control to “SLOW” position. OIL Place shift lever indicator in “F” (forward) position. Tines LEVEL will not turn. Lift handle to raise tines out of ground. Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from OIL tines. FILLER When you have completed your turn-around, release PLUG the drive control bar and lower handle. Place shift OIL DRAIN
Resumo do conteúdo contido na página número 10
OPERATION Place throttle control in “FAST” position. Soil conditions are important for proper tilling. Tines will not readily penetrate dry, hard soil which may con tribute Move choke control to full “CHOKE” position. to excessive bounce and diffi cult handling of your tiller. Grasp recoil starter handle with one hand and grasp Hard soil should be mois tened before tilling; however, tiller handle with other hand. Pull rope out slowly until extremely wet soil will “ball
Resumo do conteúdo contido na página número 11
MAINTENANCE MAINTENANCE SCHEDULE REGULAR SERVICE PERIOD (3) First Every Every Every Refer Each month 3 months 6 months year ITEM Performed at every indicated to use month or operating hour interval, or or or or page whichever comes first. 20 Hrs. 50 Hrs. 100 Hrs. 300 Hrs. Check level Engine Oil 27 Change Reduction gear Check level oil (applicable 27 models only) Change Check Air Cleaner (1) (*) (1) Clean 28 (**) Replace Sediment cup Clean 31 Spark plug Clean-Readjust 32 Replace Spark arr
Resumo do conteúdo contido na página número 12
MAINTENANCE Disconnect spark plug wire before performing any maintenance (except car bure tor adjustment) to prevent accidental start ing of engine. Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. Clean muffl er area of all grass, dirt, and debris. Do not touch hot muffl er or cylinder fi ns as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classifi
Resumo do conteúdo contido na página número 13
SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER CLEVIS PIN TO ADJUST HANDLE HEIGHT (See Fig. 18) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. NUT “C” First loosen handle lock lever. Handle can be positioned at different settings between NUT “HIGH” and “LOW” positions. “D” Retighten handle lock lever secu
Resumo do conteúdo contido na página número 14
SERVICE AND ADJUSTMENTS GROUND DRIVE BELT ADJUSTMENT TO REPLACE GROUND DRIVE BELT (See Fig. 21) (See Fig. 21) For proper belt tension, the extension spring should Remove belt guard (See “TO REMOVE BELT GUARD” in this section of this manual). have about 5/8 inch stretch when drive control bar is in “EN GAGED” position. This tension can be attained as Remove old belt by slipping off engine pulley fi rst then follows: remove from transmission pulley. Loosen cable clip scr
Resumo do conteúdo contido na página número 15
SERVICE AND ADJUSTMENTS To maintain the superb tilling performance of this TINE REPLACEMENT ma chine the tines should be checked for sharpness, (See Figs. 22, 23, and 24) wear, and bending, particularly the tines which are next to the transmission. If the gap between the tines CAUTION: Tines are sharp. Wear ex ceeds 3-1/2 inches (9 cm), they should be replaced gloves or other protection when han- or straight ened as necessary. dling tines. New tines should be assembled
Resumo do conteúdo contido na página número 16
SERVICE AND ADJUSTMENTS ENGINE CARBURETOR The carburetor has been preset at the factory and ad just ment should not be necessary. However, engine per formance can be affected by dif ferenc es in fuel, tem per a ture, al ti tude or load. If the carburetor does need ad just ment, contact your nearest authorized service center/de part ment. The air fi lter must be assembled to the carburetor when running engine. Best carburetor adjustment is obtained when fuel tank is 1/4 full.
Resumo do conteúdo contido na página número 17
STORAGE Immediately prepare your tiller for storage at the end of the ENGINE OIL season or if the unit will not be used for 30 days or more. Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). WARNING: Never store the tiller with gasoline in the tank inside a build ing CYLINDER(S) where fumes may reach an open fl ame Remove spark plug. or spark. Allow the engine to cool before Pour 1 ounce (29 ml) of oil through sp
Resumo do conteúdo contido na página número 18
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not star t 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded.
Resumo do conteúdo contido na página número 19
REPAIR PARTS TILLER - - MODEL NUMBER 500RTT(96093000100), PRODUCT NUMBER 960 93 00-01 HANDLE ASSEMBLY 8 6 2 30 10 13 33 12 2 14 11 41 15 27 27 29 37 21 16 37 18 4 20 19 26 24 11 17 23 31 Handle_assy_33 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 2 532 00 92-66 Grip, Handle 21 532 18 11-27 Handle 4 532 15 92-28 Bar Assembly, Control 23 532 08 67-77 Screw, Hex Washer Hd. Slotted 6 532 18 06-
Resumo do conteúdo contido na página número 20
REPAIR PARTS TILLER - - MODEL NUMBER 500RTT(96093000100), PRODUCT NUMBER 960 93 00-01 MAINFRAME, LEFT SIDE 7 9 6 8 39 10 1 5 3 2 3 2 12 13 21 4 65 38 14 37 33 16 36 32 35 34 31 27 19 40 29 22 30 66 23 28 3 44 24 15 40 26 mainframe_left_17 25 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 873 51 05-00 Nut, Keps 5/16-18 25 532 12 47-88 Clip, Hairpin 2 810 04 06-00 Washer, Lock 3/8 26 532 16 67-92 Gu
