Manual do usuário Yard-Man 31AE993J401

Manual para o dispositivo Yard-Man 31AE993J401

Dispositivo: Yard-Man 31AE993J401
Categoria: Varredores de neve
Fabricante: Yard-Man
Tamanho: 7.17 MB
Data de adição: 7/26/2013
Número de páginas: 28
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Yard-Man 31AE993J401. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Yard-Man 31AE993J401.

Para sua conveniência

Se a consulta dos manuais Yard-Man 31AE993J401 diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Yard-Man 31AE993J401 no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Yard-Man 31AE993J401 em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Yard-Man 31AE993J401 Manual de instruções - Online PDF
Advertisement
« Page 1 of 28 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Yard-Man 31AE993J401, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Yard-Man 31AE993J401. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

OPERATOR’S MANUAL
45” Snow Thrower
Model 31AE993J401
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operat

Resumo do conteúdo contido na página número 2

TABLE OF CONTENTS Content Page Important Safe Operation Practices................................................................... 3 Assembling Your Snow Thrower ....................................................................... 5 Knowing Your Snow Thrower ............................................................................ 7 Operating Your Snow Thrower .......................................................................... 9 Making Adjustments .................................

Resumo do conteúdo contido na página número 3

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning. WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain o

Resumo do conteúdo contido na página número 4

5. Never run an engine indoors or in a poorly ventilated Maintenance And Storage area. Engine exhaust contains carbon monoxide, an 1. Never tamper with safety devices. Check their proper odorless and deadly gas. operation regularly. 6. Do not operate machine while under the influence of 2. Disengage all clutch levers and stop engine. Wait until alcohol or drugs. the auger/impeller come to a complete stop. Disconnect 7. Muffler and engine become hot and can cause a burn. Do the spark plu

Resumo do conteúdo contido na página número 5

SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: Any reference in this manual to the left or right side of the snow thrower is observed from the operator’s position. Upper Handle Unpacking Steering Cable  Remove staples from the top, sides, and ends of the shipping crate.  Set panels aside to avoid tire punctures or personal Tighten these injury. Wing Nuts  Remove and discard plastic bag that covers unit. Lower Handle  Roll the unit out of the crate.  Check the crate thoroughly for loose

Resumo do conteúdo contido na página número 6

 Tighten the two wing nuts already in place on the upper holes and secure the handles firmly.Slide the Alternator Lead shift rod connector down over the end of the lower shift rod. Tap the connector until it locks over the Alternator lower shift rod. See Figure 2. Lead NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or change directions. Lamp Wire  Remove the hairpin clip from the upper chute crank (Wheels left out for cl

Resumo do conteúdo contido na página número 7

 Recheck adjustment; readjust as necessary and tighten the jam nut. Shave Plate “Z” End Carriage Bolts Jam Nut High Skid Low Hex Nuts Shoes Auger Control Cable Figure 8 Figure 7 NOTE: Make certain the entire bottom surface of skid Skid Shoes shoe is against the ground to avoid uneven wear on the skid shoes. The space between the shave plate and the ground can be adjusted by repositioning the skid shoes. For close Tire Pressure (Pneumatic Tires) snow removal, as when using on a smooth con

Resumo do conteúdo contido na página número 8

IMPORTANT: Always release traction the control before Chute Tilt Control changing speeds. The distance snow is thrown can be changed by Forward adjusting the angle of the chute assembly. Move the Your snow thrower has six forward (F) speeds. Position chute tilt control forward to decrease the distance, number one (1) is the slowest and position number six toward the rear to increase. See Figure 9. (6) is the fastest. Discharge Chute Reverse Your snow thrower has two reverse (R) speeds. R1 i

Resumo do conteúdo contido na página número 9

SECTION 4: OPERATING YOUR SNOW THROWER WARNING: The electric starter is Before Starting equipped with a grounded three-wire WARNING: Read, understand, and power cord and plug and is designed to operate on 120 volt AC household follow all instructions and warnings on the current. It must be used with a properly machine and in this manual before grounded three-prong receptacle at all operating. times to avoid the possibility of electric shock. Follow all instructions carefully Gas And Oil Fill-u

Resumo do conteúdo contido na página número 10

 Squeeze the traction control against the right To Stop Engine handle and the snow thrower will move. Release it  Run engine for a few minutes before stopping to and the drive motion will stop. help dry off any moisture on the engine. IMPORTANT: NEVER move the shift lever without first  To help prevent possible freeze-up of starter, releasing the traction control. Doing so will cause proceed as follows. premature wear to the drive system’s friction wheel. Electric Starter:  Connect pow

Resumo do conteúdo contido na página número 11

 Loosen the jam nut on the traction drive cable and thread the cable in or out as necessary. Refer to Shift Lever Figure 7.  Retighten the jam nut to secure the cable when Hairpin Clip correct adjustment is reached.  Reassemble the frame cover. NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower. Flat Washer Trigger Cables Shift Arm Drive Actuator Ferrule Bracket Auger Actuator Bracket Shift Arm Upper Shift Rod Clutch Rod Hex Nut

Resumo do conteúdo contido na página número 12

warranty, operator must maintain the snow thrower Discharge Chute as instructed in this manual. The base of the discharge chute and the spirals on the • Some adjustments will have to be made chute crank should be lubricated at least every 25 periodically to maintain your unit properly. hours of use. Apply the lubricant under the base of the  All adjustments in the service and adjustments chute and where the spirals contact the discharge sections of this manual should be checked at least

Resumo do conteúdo contido na página número 13

 Carefully spin the auger around by hand to  Replace belts as necessary as outlined in Service disperse the lubricant. Section.  Reinstall the shear bolts. Traction Control / Auger Control Lock Check Friction Wheel Rubber The cams on the ends of the control rods which Follow the instructions below to check the condition of interlock the traction drive and auger drive clutches the friction wheel rubber every 25 hours of operation. must be lubricated at least once a season or every 25 hours

Resumo do conteúdo contido na página número 14

 Remove the six carriage bolts (three per side),  Pull the brake bracket assembly towards the cable belleville washers and hex nuts which attach slide guide roller and unhook the auger cable “Z” fitting. shoes to the snow thrower on two sides. See Figure 8.  Reassemble new slide shoes with the hardware Engine Pulley removed earlier (cupped side of belleville washer against the slide shoes). Make certain the slide shoes are adjusted to be level.  To remove the shave plate, remove slide

Resumo do conteúdo contido na página número 15

assembly and secure with flat washer and cotter Auger Belt Brake Bracket Assembly pin. Reassemble the large shoulder bolt and lock Idler Pulley washer. Refer to Figure 17. Auger Pulley  Reassemble belt cover and chute crank. Changing Friction Wheel Rubber The rubber on the friction wheel is subject to wear and should be checked after the first 25 hours of operation, and periodically thereafter. Replace the friction wheel rubber if any signs of wear or cracking are found.  Drain the gasol

Resumo do conteúdo contido na página número 16

the right side of the hex shaft will fall and the  Secure with the bell washer and hex bolt removed sprocket should remain hanging lose in the chain. earlier.  Lift the friction wheel assembly out between the  Secure the frame cover with six self-tapping axle shaft and the drive shaft assemblies. screws. Put the snow thrower down to its normal  Remove the six screws from both sides of the operating position. friction wheel assembly and remove friction wheel NOTE: If you placed plastic fi

Resumo do conteúdo contido na página número 17

SECTION 8: TROUBLESHOOTING Problem Cause Remedy Engine fails to start. 1. Fuel tank empty, or stale fuel. 1. Fill tank with fresh gasoline. 2. Blocked fuel line. 2. Clean the fuel line. 3. Choke not in ON position 3. Move switch to ON position 4. Faulty spark plug. 4. Clean, adjust gap or replace. 5. Safety key not in ignition switch on engine. 5. Insert the key fully into the switch. 6. Spark plug wire disconnected. 6. Connect spark plug wire. 7. Primer button not being used properly. 7. Refe

Resumo do conteúdo contido na página número 18

Model 31AE993J401 47 8 8 43 13 25 16 14 40 21 31 42 25 8 7 14 21 5 1 25 55 51 48 29 25 27 14 13 58 18 3 26 17 54 56 34 25 9 53 45 50 57 14 34 13 26 32 44 5 22 13 33 52 46 49 41 25 5 14 11 2 35 19 13 28 6 12 15 36 37 NOTE: For painted parts, please refer to the list of color codes below. Please add 38 29 20 the applicable color code, wherever needed, to the part number to order a 24 replacement part. For instance, if a part 13 29 numbered 700-sextets is painted Yard- Man Green, the part number to

Resumo do conteúdo contido na página número 19

Model 31AE993J401 Ref. Ref. Part No. Part Description Part No. Part Description No. No. 1. 05244A Bearing Housing 30. 738-0281 Shoulder Screw 2. 618-0281A Bracket Assembly: Auger Break 31. 741-0185 Self-Aligning Bearing 3. 684-0090A Impeller Assembly: 16” 32. 741-0192 Flange Bearing w/ Flats 4. 710-0371 Hex Lock Bolt 5/16-18 x .875” 33. 741-0475 Plastic Bushing 5. 710-0451 Carriage Bolt 5/16-18 x .750” 34. 741-0494 Flange Bushing 6. 710-0459A Hex Screw, Special 3/8-24 x 1.5” 35. 747-0980 Idler

Resumo do conteúdo contido na página número 20

Model 31AE993J401 18 12 63 8 17 79 76 9 18 50 11 16 73 45 26 62 18 55 80 53 69 66 24 49 35 41 48 36 15 45 61 45 10 35 4 55 19 45 42 31 47 5 54 56 32 3 39 1 30 66 42 16 34 23 67 60 75 27 6 62 33 55 65 55 14 47 50 33 26 22 55 51 22 56 71 38 51 20 64 61 27 58 48 46 21 29 2 57 13 31 80 15 46 20 43 47 46 46 29 40 19 60 55 13 43 56 70 30 68 7 31 59 37 44 77 28 31 52 18 18 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to t


Manuais similares
# Manual do usuário Categoria Baixar
1 Yard-Man 310183 Manual de instruções Varredores de neve 20
2 Yard-Man 31340-8 Manual de instruções Varredores de neve 4
3 Yard-Man 31380-8 Manual de instruções Varredores de neve 8
4 Yard-Man 31353-8 Manual de instruções Varredores de neve 12
5 Yard-Man 316E733E401 Manual de instruções Varredores de neve 26
6 Yard-Man 31AE573H401 Manual de instruções Varredores de neve 5
7 Yard-Man 310193 Manual de instruções Varredores de neve 1
8 Yard-Man 31383-8 Manual de instruções Varredores de neve 1
9 Yard-Man 316E753F401 Manual de instruções Varredores de neve 8
10 Yard-Man 31AE553F401 Manual de instruções Varredores de neve 7
11 Yard-Man 31AE993I401 Manual de instruções Varredores de neve 11
12 Yard-Man 5KL Manual de instruções Varredores de neve 2
13 Yard-Man 31AH553G401 Manual de instruções Varredores de neve 4
14 Yard-Man 7100-2 Manual de instruções Varredores de neve 20
15 Yard-Man 7100-1 Manual de instruções Varredores de neve 47
16 Agri-Fab 45-0402 Manual de instruções Varredores de neve 2
17 Agri-Fab 45-0418 ATV Manual de instruções Varredores de neve 1
18 Agri-Fab 45-0418 Manual de instruções Varredores de neve 1
19 Alliance Laundry Systems DRYING TUMBLERS 70269501R3 Manual de instruções Varredores de neve 2
20 Ariens 924 SNO-THRO 924109 Manual de instruções Varredores de neve 60