Resumo do conteúdo contido na página número 1
This Manual is Bookmarked
Operating Instructions and Parts Manual
16-Inch Woodworking Band Saw
Model JWBS-16B
WMH TOOL GROUP, Inc.
2420 Vantage Drive
Elgin, Illinois 60124 Part No. M-708749B
Ph.: 800-274-6848 Revision A 03/08
www.wmhtoolgroup.com Copyright © 2008 WMH Tool Group, Inc.
Resumo do conteúdo contido na página número 2
Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area call 1-800-27
Resumo do conteúdo contido na página número 3
Table of Contents Warranty and Service....................................................................................................................................2 Table of Contents..........................................................................................................................................3 Warning.........................................................................................................................................................4 Int
Resumo do conteúdo contido na página número 4
Warning 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This band saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a band saw, do
Resumo do conteúdo contido na página número 5
blahblahblah 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. Do not overreach or use excessive force to perform any machine operation. 23. Use the right tool at the correct sp
Resumo do conteúdo contido na página número 6
Introduction This manual is provided by Jet covering the safe operation and maintenance procedures for model JWBS-16B Band Saw. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, please contact either yo
Resumo do conteúdo contido na página número 7
Canada. The green colored grounding ear, lug, Grounding Instructions or tab, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box, as shown in This machine must be C, Fig. 1. grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric
Resumo do conteúdo contido na página número 8
Unpacking Remove the packing material from the band saw. Note: Remove the plywood and bolts from the base. Inspect the machine for damage. Report any damage to your distributor and shipping agent. Move the saw to its permanent working location. The site should be dry, well lit, and have enough room to handle long stock and the service and/or adjustment of the machine from any side. Move the band saw off the skid. Clean all rust protected surfaces with a mil
Resumo do conteúdo contido na página número 9
Assembly and Setup Base Support Extension 1. Attach straps (A, Fig. 1A) to extension base (B, Fig. 1A) with (2) 5/16-18 button head cap screws (C, Fig. 1A) and with (2) 5/16 flat washers (D, Fig. 1A). If needed punch holes through striping decal. NOTE: Leave screws slightly loose. 2. Repeat for opposite end of extension base. Figure 1A 3. Insert straps through slits in base of machine lining up holes in machine base with tapped holes in strap (Fig 1B) 4. Attach
Resumo do conteúdo contido na página número 10
Adjusting Blade Tension 1. Disconnect machine from the power source, unplug. 2. Turn blade tension hand wheel (E, Fig. 2) counter-clockwise to tension blade, and clockwise to loosen the tension. A gauge on the upper wheel slide bracket (F, Fig. 2) indicates the approximate tension according to the width of the blade. The JWBS-16B comes with a 3/4” blade so the tension should be set at 3/4” when using this blade. As you become familiar with the saw, you may find it necessary
Resumo do conteúdo contido na página número 11
Lower Blade Guide Adjustment Disconnect machine from the power source, unplug before making any adjustments! Blade teeth are sharp! Use care when working near the saw blade. Failure to comply may cause serious injury! 1. Blade tension and tracking must be properly adjusted prior to blade guide setup. Figure 3 2. The blade guard has been removed in Figure 4 for photo purposes only. 3. Loosen the socket head cap screws (G, Fig. 4) and position the blade guide assembly (
Resumo do conteúdo contido na página número 12
Mounting the Table 1. Mount the trunnion support bracket (A, Fig. 5) to the bandsaw with four 5/16” x 1-1/2” hex cap bolts, and four 5/16” lock washers (B, Fig. 5). 2. Remove the round table insert (C, Fig. 5) found where the blade goes through the table. Also, remove the table pin (D, Fig. 5) found on the side of the table. 3. Slide saw blade through slot in table where the table pin was located. Rotate the table 90 degrees so that the miter slot is parallel to the blade, and t
Resumo do conteúdo contido na página número 13
Rail Assembly (optional accessory) 1. Attach the front rail (A, Fig. 8) to the cast iron table with two 1/4” x 5/8” hex cap bolts, two 1/4” lock washers, and two 1/4” flat washers. Bolts should be in approximately the center of the slot. Hand tighten only at this time. 2. Attach the rear rail (B, Fig. 8) to the table with two 1/4” x 5/8” hex cap bolts, two 1/4” lock washers, and two 1/4” flat washers. Bolts should be in approximately the center of the Figure 8 slot. Hand tight
Resumo do conteúdo contido na página número 14
4. Check the clearance between the table and the fence. The gap should be the same at the front of the table as it is at the rear. If the gap width is different, adjust the foot at the rear of the fence until the gap width is the same, Figure 11. Note: You can also adjust the front rail, or rear rail up, or down to achieve the proper clearance. 5. With a square verify the fence face is perpendicular to the table top. If it is not the front rail will need to be adjusted paral
Resumo do conteúdo contido na página número 15
Tilting the Table 1. Disconnect the machine from the power source, unplug. 2. Loosen the lock knobs (A, Fig. 13). 3. Tilt table up to 45 degrees to the right, or up to 10 degrees to the left. 4. Tighten the lock knobs. Figure 13 Note: Table stop bolt (B, Fig. 13) must be removed to tilt table to the left. Height Scale Adjustment 1. Disconnect the machine from the power source, unplug. 2. The upper blade guide should be set about 1/8” above the material to be cut
Resumo do conteúdo contido na página número 16
Changing Blades Disconnect machine from the power source, unplug! Blade teeth are sharp! Use care when handling the saw blade. Failure to comply may cause serious injury! 1. Remove the table insert (A, Fig. 16), and table pin (B, Fig. 16). 2. Lower the upper blade guide assembly about half way by loosening the lock knob (F, Fig. 17) and turning the hand wheel (G, Fig. 17). 3. Loosen socket head cap screw (C, Fig. 16) and slide the blade guide assembly back as far as it will go.
Resumo do conteúdo contido na página número 17
Replacing V-Belt 1. Disconnect the machine from the power source. 2. Release blade tension by turning blade tension hand wheel clockwise. 3. Release belt tension by loosening the two hex cap bolts (A, Fig. 19). Raise the motor and tighten hex cap bolts to take the tension off the belt. 4. Open the lower wheel door and remove hex Figure 19 nut, and washer (B, Fig. 20). 5. Remove the wheel (C, Fig. 21). If the lower wheel does not come off easily you may need to use a pulley
Resumo do conteúdo contido na página número 18
Electrical Connections All electrical connections must be done by a qualified electrician! Failure to comply may result in loss of property and/or serious injury! The JWBS-16B is rated at 1-1/2 HP, 1Ph, 115V/230V, prewired 115V. The bandsaw comes with a 115V plug (A, Fig. 22). If you switch the motor to 230V a plug needs to be purchased for the bandsaw that matches the 230V outlet you intend to use. Confirm power at the site is the same as the saw before making any electr
Resumo do conteúdo contido na página número 19
Troubleshooting Trouble Possible Cause Solution 1. Saw unplugged 1. Check plug connections 2. Fuse blown or circuit 2. Replace fuse or reset circuit Saw stops or will not start breaker tripped breaker 3. Cord damaged 3. Replace cord 1. Stop not adjusted correctly 1. Check blade with square and adjust stop Does not make accurate 45 ° or 2. Angle pointer not set 2. Check blade with square accurately and adjust pointer 90 ° cuts 3. Miter gauge out of 3. Adjust miter gauge adjustment
Resumo do conteúdo contido na página número 20
Upper Wheel Assembly Index No. Part No. Description Size Qty 1 ...............JWBS16B-101 .........Saw Body............................................................. .................................... 1 2 ...............TS-0152011 .............Carriage Bolt ........................................................ 5/16-18x1.................... 6 3 ...............JWBS18-103............Upper Wheel Bracket........................................... .................................... 2 4
