Resumo do conteúdo contido na página número 1
Model No. WESY93190
Serial No.
9925
Write the serial number in the space
above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our cus
Resumo do conteúdo contido na página número 2
Table of Contents IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 HOW TO USE THE HOME GYM S
Resumo do conteúdo contido na página número 3
Before You Begin ¨ Thank you for selecting the versatile WEIDER PRO Service Department toll-free at 1-800-999-3756, ¨ 9925 Training System. The WEIDER 9925 offers a Monday through Friday, 6 a.m. until 6 p.m. Mountain selection of weight stations designed to develop every Time (excluding holidays). To help us assist you, major muscle group of the body. Whether your goal is please note the product model number and serial to tone your body, build dramatic muscle size and number before calling. The
Resumo do conteúdo contido na página número 4
Assembly Note: This introduction will save you more Identifying Parts time than it takes to read it! To help you identify the small parts used in assem- bly, we have included a PART IDENTIFICATION CHART located in the center of this manual. Place Making Things Easier for Yourself the chart on the floor or work table and use it to Everything in this manual is designed to ensure quickly identify different parts as you open the pack- that the assembly of our products can be complet- ages for each s
Resumo do conteúdo contido na página número 5
1 FRAME ASSEMBLY 1. Before beginning assembly, be sure that you have read and understand the information in the box above. 58 58 Locate and open the parts bags labeled ÒFRAME 20 55 ASSEMBLY BAG ONEÓ and ÒFRAME ASSEMBLY BAG TWO.Ó 55 Press two 2Ó Square Outer Caps (58) onto the indi- 20 cated ends of the Weight Base (14). Press a 2Ó Square Inner Cap (56) into the end of the Weight Base. 14 49 Insert four 5/16Ó x 2 1/2Ó Carriage Bolts (49) up 13 through the Weight Base (14). 49 Insert four 5/16Ó x
Resumo do conteúdo contido na página número 6
3. Press a 2Ó Square Inner Cap (56) into the open end 3 of the Top Frame (2). Press a 2Ó Square Inner Cap 56 (56) into each side of the Butterfly Frame (3). Press 91 two 1Ó Round Inner Caps (70) into the top of the 40 Butterfly Frame. 56 20 92 70 2 Attach the Butterfly Frame (3) to the Top Frame (2) with a 5/16Ó x 3Ó Bolt (92). Make sure the Bolt is on the side shown. 3 55 Finish attaching the Butterfly Frame (3) to the Top Frame (2) with a 5/16Ó Nylon Jam Nut (91), a 5/16Ó x 56 2 3/4Ó Bolt (5
Resumo do conteúdo contido na página número 7
7. Insert two Weight Guides (23) into one of the brack- 7 ets on the Weight Base (14). Attach the lower ends of the Weight Guides with a 5/16Ó x 6Ó Bolt (67), two 1/2Ó x 3/4Ó Spacers (69), and a 5/16Ó Nylon Locknut 23 (40). Do not overtighten the Nylon Locknut. 23 Attach the other Weight Guides (23) in the same manner. 40 14 67 69 8. Slide a Weight Bumper (27) onto each of the Weight 8 Guides (23). Slide eight Weights (90) onto each set of Weight Guides (23). Make sure the pin grooves are on the
Resumo do conteúdo contido na página número 8
10. Lubricate the insides of the holes in the Top Weights 10 (24) as shown. Slide a Top Weight onto each set of Weight Guides (23). 24 Lubricate 24 23 Lubricate 23 11. Attach the Top Frame (2) to the Ab Upright (1) with 55 11 two 5/16Ó x 2 3/4Ó Bolts (55), two 5/16Ó Washers (20) and two 5/16Ó Nylon Locknuts (40). Do not tighten 20 55 the Nylon Locknuts yet. 20 Attach the Butterfly Frame (3) to the Leg Press 3 Upright (4) with two 5/16Ó x 2 3/4Ó Bolts (55), two 2 5/16Ó Washers (20), and two 5/16Ó
Resumo do conteúdo contido na página número 9
13. Attach the Leg Press Plate (11) to the Adjustment 13 Tube (10) with a 5/16Ó x 2 1/2Ó Bolt (39), two 5/16Ó 10 Washers (20) and a 5/16Ó Nylon Locknut (40). Make 40 20 sure the Leg Press Plate and Adjustment Tube are 48 oriented as shown. Press a 1 3/4Ó Square Inner Cap (48) into the 39 Adjustment Tube (10). Angle 11 14. Attach the Adjustment Tube (10) to the Leg Press 14 10 73 Arm (9) with the Lock Pin (73). Make sure the Leg Press Plate (11) is oriented as shown. Press two 2Ó Square Inner Ca
Resumo do conteúdo contido na página número 10
17. Attach a Press Arm (7) to one side of the Press 17 Frame (12) with two 5/16Ó x 2 1/2Ó Bolts (39) and two 5/16Ó Nylon Locknuts (40). Attach the other Press Arm (7) to the Press Frame 39 7 (12) in the same manner. 40 7 12 18. Press a 1Ó Round Inner Cap (70) into the indicated 18 48 end of one Press Arm (7). Press a 1 3/4Ó Square Inner Cap (48) into the Press Arm. 70 Repeat this step for the other Press Arm (not shown). 7 19. Lubricate both axles on the Butterfly Frame (3). 19 Refer to the dra
Resumo do conteúdo contido na página número 11
20. Press a 1 3/4Ó Square Inner Cap (48) into the lower 20 end of the Left Arm (6) and the Right Arm (5). 5 6 48 48 21 CABLE ASSEMBLY 21. Locate and open the parts bags labeled ÒCABLE ASSEMBLYÓ and ÒPULLEYS.Ó During steps 19 through 50, refer to the CABLE DIA- GRAMS on pages 26 and 27 of this manual to verify proper cable routing. Before beginning this section, fully unwind the five Cables and identify the Cables by comparing the lengths and the ends. The approxi- mate length of each Cable, in i
Resumo do conteúdo contido na página número 12
23. Wrap the Butterfly Cable (89) around a 3 1/2Ó Pulley 23 Wide Tab (82) as shown. Attach the Pulley and two Pulley Covers (94) to the bracket on the 42 Wide Tab Leg Press Upright (4) with a 99 94 Stress-point 4 3/8Ó x 2 1/4Ó Bolt (99), a 3/8Ó on Cable Washer (38) and a 3/8Ó Nylon 94 Locknut (42). The Pulley Covers must be oriented as shown in 38 the inset drawing. Note that the 94 wide tab is over the stress- 82 point, where the Cable wraps 82 around the Pulley. Use this ori- entation of the P
Resumo do conteúdo contido na página número 13
27. Locate the Rear Cable (87)Ñthis is the shortest 27 Cable. Slide one end of the Rear Cable onto the 91 92 5/16Ó x 3Ó Bolt (92). Thread another 5/16Ó Nylon Jam Nut (91) onto the Bolt, but do not fully tighten it. 87 Leave enough room between the two Jam Nuts for the Cable to pivot. 28. Attach a 3 1/2Ó Pulley (82) and two Pulley Covers 28 (94) to the upper hole in a Large ÒUÓ Bracket (84) with a 3/8Ó x 2 1/4Ó Bolt (99) and a 3/8Ó Nylon Locknut (42). Orient the wide tab on the Pulley Covers as s
Resumo do conteúdo contido na página número 14
31. Locate the Press Cable (88)Ñthis is the longest 31 Cable. Attach the end of the Press Cable (88) to the Large ÒUÓ Bracket (84) with a 1/4Ó Nylon Locknut (44) and a 1/4Ó Washer (37). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are 44 showing above the Nylon Locknut, as shown in the inset drawing. 37 84 44 88 37 84 88 32. Wrap the Press Cable (88) around a 3 1/2Ó Pulley 32 (82) in the direction shown. Attach the Pulle
Resumo do conteúdo contido na página número 15
34. Wrap the Press Cable (88) around a 3 1/2Ó Pulley 34 (82) in the direction shown. Attach the Pulley and two Pulley Covers (94) to the lower set of holes in the Pulley Plates (31) with a 3/8Ó x 2 1/4Ó Bolt (99) and a 31 3/8Ó Nylon Locknut (42). Orient the wide tab on the Pulley Covers as shown. 99 42 94 94 82 88 Wide Tab 35. Route the Press Cable (88) around a 3 1/2Ó Pulley 35 (82) in the direction shown. Attach the Pulley and two Pulley Covers (94) to the Leg Press Upright (4) with a 4 3/8Ó x
Resumo do conteúdo contido na página número 16
38. Wrap the Press Cable (88) around a 3 1/2Ó Pulley 38 76 38 (82) in the direction shown. Attach the Pulley and two Pulley Covers (94) to the indicated hole in the Press Frame (12) with a 3/8Ó x 3 3/4Ó Bolt (76), two 3/8Ó Washers (38) and a 3/8Ó Nylon Locknut (42). Orient the wide tab on the Pulley Covers as shown. 94 Crossbar 88 38 42 Wide Tab 12 82 39. Wrap the Press Cable (88) around a ÒVÓ Pulley (81). 39 Attach the ÒVÓ Pulley to the lower bracket on the Leg Press Upright (4) with a 3/8Ó x 2
Resumo do conteúdo contido na página número 17
42. Remove the 3/8Ó Nylon Locknut (42) from the 42 3/8Ó x 5Ó Bolt (74) attached in step 40. Wrap the Press Cable (88) around a 3 1/2Ó Pulley (82) in the 9 direction shown. Attach the Pulley and two Pulley Wide Tab Covers (94) to the Leg Press Arm (9) with the 42 3/8Ó x 5Ó Bolt, a 3/8Ó Washer (38) and the 3/8Ó Nylon 82 Locknut. Orient the wide tab on the Pulley Covers as shown. 38 94 88 74 43. Slide a 5/16Ó Washer (20) onto a 5/16Ó x 2 3/4Ó Bolt 43 (55). Insert the Bolt into the Front Seat Frame
Resumo do conteúdo contido na página número 18
46. Locate one of the preassembled pairs of Pulley 46 Plates (31) and remove both 3 1/2Ó Pulleys (82). Route the High Cable (85) around a 3 1/2Ó Pulley (82) in the direction shown. Attach the Pulley and two 85 Pulley Covers (94) to the Pulley Plates (31) with a 94 82 3/8Ó x 2 1/4Ó Bolt (99) and a 3/8Ó Nylon Locknut (42). Note: The end of the Pulley Plates (31) with two 94 holes should be pointed downward. Orient the Wide Tab wide tab on the Pulley Covers as shown. 42 99 End with two 31 holes sho
Resumo do conteúdo contido na página número 19
50. Wrap the Low Cable (86) around a 3 1/2Ó Pulley (82) 50 in the direction shown. Attach the Pulley and two Pulley Covers (94) to the welded tube on the Ab 1 Upright (1) with a 3/8Ó x 3 3/4Ó Bolt (76), a 3/8Ó Washer (38) and a 3/8Ó Nylon Locknut (42). Orient 94 the wide tab on the Pulley Covers as shown. 42 86 Welded Tube 38 82 94 Wide Tab 76 51. Wrap the Low Cable (86) around a 3 1/2Ó Pulley (82) 51 in the direction shown. Attach the Pulley and two Pulley Covers (94) to the lower set of holes
Resumo do conteúdo contido na página número 20
53. Wrap the Low Cable (86) around a 3 1/2Ó Pulley (82) 53 in the direction shown. Attach the Pulley and two Pulley Covers (94) to the indicated hole in the Leg 86 42 Lever (15) with a 3/8Ó x 3 3/4Ó Bolt (76), two 3/8Ó 38 Washers (38) and a 3/8Ó Nylon Locknut (42). Orient 82 the wide tab on the Pulley Covers as shown. 15 38 76 94 Wide Tab 54. Wrap the Low Cable (86) around a 3 1/2Ó Pulley (82) 54 in the direction shown. Attach the Pulley and two Pulley Covers (94) to the indicated hole in the Ab
