Resumo do conteúdo contido na página número 1
INSTALLATION &
OPERATION MANUAL
VCD SERIES CHIP WARMERS
MODELS:
VCD22* ML-138037
VCD44 ML-138069
*Formerly VCD5
For additional information on Vulcan-Hart or to locate an authorized parts
and service provider in your area, visit our website at www.vulcanhart.com
VULCAN-HART 3600 NORTH POINT BLVD.
DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC BALTIMORE, MD 21222
www.vulcanhart.com Vulcan ©2010 All Rights Reserved F-38053 (09-10)
Resumo do conteúdo contido na página número 2
VCD SERIES CHIP WARMER F-38053 (09-10) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START- UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITYOF THIS OR ANY OTHER APPLIANCE. Improper installation, adjustment, alteration, service, or maintenance c
Resumo do conteúdo contido na página número 3
VCD SERIES CHIP WARMER F-38053 (09-10) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 4
VCD SERIES CHIP WARMER F-38053 (09-10) GENERAL If the warmer is found to be INTRODUCTION damaged, save the packaging material and contact the carrier Vulcan-Hart Chip Warmers are within 15 days of delivery. produced with quality workmanship and material. Proper installation, usage, and maintenance of your warmer will result Carefully unpack warmer and place in a in many years of satisfactory work accessible area. performance. 1. Remove banding holding the It is su
Resumo do conteúdo contido na página número 5
VCD SERIES CHIP WARMER F-38053 (09-10) ACCESS PANEL POSITIONING: SCOOP HOLDER INSTALLATION: 1. Ensure that top Baffle notches The Chip Scoop Holder will secure up to are over carriage bolts. a 6“ wide scoop. 2. Insert Access Panel onto the back of the Chip Warmer. (Fig. 1) 1. On either the left or right side of the Chip Warmer, loosen four side screws one revolution. 2. Position the Chip Scoop Holder. (Fig. 3) (Fig. 1) 3. On both sides of Access Panel, (Fig. 3)
Resumo do conteúdo contido na página número 6
VCD SERIES CHIP WARMER F-38053 (09-10) All warmers are ELECTRICAL REQUIREMENTS equipped with a three-prong plug. It is imperative that this plug must be ELECTRICAL CODES & STANDARDS: connected into a properly grounded three-prong receptacle. If the The warmer must be installed in receptacle is not the proper accordance with: grounding type, contact an electrician. Do not remove the In the United States of America: grounding prong from this plug. 1. State and Local Co
Resumo do conteúdo contido na página número 7
VCD SERIES CHIP WARMER F-38053 (09-10) OPERATION BEFORE FIRST USE TESTING THE CHIP WARMER The Chip Warmer should be thoroughly The Warmer and its cleaned before initial use. parts are hot. Be very careful when operating, cleaning, or servicing the warmer. Always disconnect electrical power to the Chip Warmer before cleaning or servicing. Before using the Chip Warmer for the first time, verify that it operates properly. 1. Remove Access Panel by unlocking clips. 1.
Resumo do conteúdo contido na página número 8
VCD SERIES CHIP WARMER F-38053 (09-10) OPERATION INSTRUCTIONS SHUTDOWN The Warmer and its The Warmer and its parts are hot. Be very careful when parts are hot. Be very careful when operating, cleaning, or servicing the operating, cleaning, or servicing the warmer. warmer. 1. Switch Power Switch to ON At the end of the day, switch Power position. Verify that switch Switch to OFF position. Follow cleaning illuminates. instructions in this manual, if necessary. 2. Open To
Resumo do conteúdo contido na página número 9
VCD SERIES CHIP WARMER F-38053 (09-10) MAINTENANCE EXTERIOR: CLEANING Refer to “STAINLESS STEEL CARE.” The Warmer and its HEAVY-DUTY CLEANING: parts are hot. Be very careful when For heavy-duty cleaning, use warm operating, cleaning, or servicing the water, a degreaser, and a plastic, warmer. stainless steel, or Scotch-Brite pad. Never rub in a circular motion -- rub Always unplug gently in the direction of the steel grain. electrical power supply before Always r
Resumo do conteúdo contido na página número 10
VCD SERIES CHIP WARMER F-38053 (09-10) 4. Never rub in a circular motion. If signs of breakdown appear, restore Always rub gently in the direction the stainless steel surface. First, of the steel grain. thoroughly clean, rinse, and dry the surface. Then, on a daily basis, apply a 5. Never leave any food products high-quality stainless steel polish or salt on the surface. Many according to manufacturer’s instructions. foods are acidic. Salt contains chloride. HEAT TINT:
Resumo do conteúdo contido na página número 11
VCD SERIES CHIP WARMER F-38053 (09-10) TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE REMEDY Chip Warmer not Plug chip warmer into correct plugged into power power source as indicated on source. serial data plate. Chip Warmer not Lighted power switch not Press power switch to ON operating in ON position. position. Check fuse and reset is necessary. No power. Check GFCI switch on outlet. GFCI or Ground Fault Circuit Moisture problem. Dry moisture problem. Indicator tripped. Damaged
Resumo do conteúdo contido na página número 12
VCD SERIES CHIP WARMER F-38053 (09-10) WIRING DIAGRAM VCD22 & VCD44 11
