Resumo do conteúdo contido na página número 1
Attachment
Illustrated
Parts List
ATTACHMENT
Mfg. No. Description
1691978 36” Tiller
1693578 36” Tiller
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Rev. 10/2001
Port Washington, WI 53074-0997 USA
TP 400-2373-01-AT-SMA
© Copyright 2001 Simplicity Manufacturing, Inc.All Rights Reserved.
Resumo do conteúdo contido na página número 2
36” Tine & Deflector Group 984363 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 1691978 36” Tiller 1693578 36” Tiller © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. TP 400-2373-01-AT-SMA 2
Resumo do conteúdo contido na página número 3
36” Tine & Deflector Group REF NO. PART NO. QTY. DESCRIPTION 1 1707990 1 PLATE, End, R.H. 2 1927557 15 LOCKNUT, Flange, 5/16-18 3 1931332 8 CARRIAGE BOLT, 5/16-18 x 5/8 4 105369 1 DEFLECTOR ASSEMBLY, R.H. 5 1679700 2 DECAL, Safety 6 105354 1 SHIELD 7 1930642 1 NUT, Hex Head, Flange, 1/4-20 8 1707938 1 CHANNEL 9 1921210 2 CAPSCREW, Hex Head, 3/8-16 x 1 10 1960353 2 WASHER 11 1930645 2 NUT, Hex, Flange, 3/8-16 12 105337 4 KEY 13 1933260 2 SCREW, Hex, Whizlock, 3/8-16 x 3/4 14 1707991 1 PLATE, End,
Resumo do conteúdo contido na página número 4
36” Housing Group 984364 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 15 16 The above parts group applies to the following Mfg. Nos.: 1691978 36” Tiller 1693578 36” Tiller © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. TP 400-2373-01-AT-SMA 4
Resumo do conteúdo contido na página número 5
36” Housing Group REF NO. PART NO. QTY. DESCRIPTION 1 105336 2 CHAIN, # 40 2 178174 1 CHAIN, # 50 3 1650841 1 TRANSMISSION SUB ASSEMBLY (Incl. Ref. Nos. 1-16, 18-38 on this page) & Incls. Ref. Nos. 1-5,7,11,17,18,19,34,36 & 38 in the 36” Tiller Drive Group) 4 915019 2 FITTING, Grease 5 105132 2 BOLT, Hex Head, Drilled & Tapped 6 1916966 4 LOCKWASHER, 1/2 7 105320 2 BAR, Side 8 1917372 4 NUT, Hex, 5/16-1 9 1917356 4 LOCKWASHER, 5/16 10 1669337 2 BEARING 11 1923362 13 LOCKNUT, 5/16-18 12 1053
Resumo do conteúdo contido na página número 6
36” Drive Group 984262 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 1691978 36” Tiller 1693578 36” Tiller © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. TP 400-2373-01-AT-SMA 6
Resumo do conteúdo contido na página número 7
36” Drive Group REF NO. PART NO. QTY. DESCRIPTION 1 923471 1 CAPSCREW, Hex Head, 7/16-14 x 1-1/4 2 1925125 2 WASHER, 3/8 3 105346 2 SPACER 4 1930650 2 LOCKNUT, Flange, 7/16-14 5 105359 2 SUPPORT 6 105339 1 SPACER 7 1707593 1 SPRING, Torsion 8 1923141 1 CAPSCREW, Hex Head, 5/16-18 x 2-3/4 9 1704716 2 SPACER 10 960171 1 WASHER, Nylon 11 1666106 1 BUSHING 12 1919326 1 WASHER, 5/16 13 176012 5 RETAINER PIN 14 1917356 1 LOCKWASHER, 5/16 15 1707564 1 GUARD, Belt 16 1917372 1 NUT, Hex, 5/1
Resumo do conteúdo contido na página número 8
36” Drive Group 984262 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 1691978 36” Tiller 1693578 36” Tiller © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. TP 400-2373-01-AT-SMA 8
Resumo do conteúdo contido na página número 9
36” Drive Group REF NO. PART NO. QTY. DESCRIPTION 46 171186 2 BEARING 47 1708180 1 CLEVIS ASSEMBLY, w/Bearings (incl. Ref. Nos. 48 & 46) 48 * 1 CLEVIS ASSEMBLY, (See Ref. No. 47) 49 912808 1 FITTING, Lube 50 159159 1 SPRING, Extension 51 1960251 2 NUT, Hex, Centerlock, 3/8-16 52 1706508 1 ARM ASSEMBLY, Idler 53 1657712 1 PULLEY, Idler 54 1923701 1 CAPSCREW, Hex Head, 3/8-16 x 2 55 1700059 1 V-BELT 56 960403 1 KEY 57 1928721 1 SETSCREW, 5/16-18 58 1706343 1 PULLEY ASSEMBLY 59 155037 2 PIN 60 16
Resumo do conteúdo contido na página número 10
0 1 2 3 4 1/2 1/2 1/2 1/2 1/4 3/4 1/4 3/4 1/4 3/4 1/4 3/4 Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer No Hardware Lockwasher Marks Grade Carriage Bolt SAE Grade 2 SAE Grade 5 SAE Grade 8 Hex Nut Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. Standard Hardware Sizing 8-32 19 2.1 30 3.4 41 4.6 When a washer or nut is identified as 1/2”, this is the
