Resumo do conteúdo contido na página número 1
MANUFACTURING, INC.
Intermediate Frame Snowthrowers
Initial setup
This Dealer Setup Instruction covers the following products:
Intermediate Frame Snowthrowers
Mfg. No. Description
1695302 SMI I1924E, 9GT, B&S 24
1695311 SMI I1924EX, 9GT, B&S 24 (CE)
1695410 SMI I1924EX, 9GT, B&S 24 (CE)
1695313 SNP I1924E, 9GT, B&S 24
1695314 SNP I1924EX, 9GT, B&S 24 (CE)
1695411 SNP I1924EX, 9GT, B&S 24 (CE)
Briggs & Stratton Yard Power Products Group Form No. 1735249
Copyright © 2007 Briggs & Stratton Corpora
Resumo do conteúdo contido na página número 2
Intermediate Frame Snowthrowers SAFETY RULES Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. GENERAL OPERATION operate the unit safely enough to protect themselves and others from injury. � Read, understand, and follow all instructions in the �
Resumo do conteúdo contido na página número 3
Intermediate Frame Snowthrowers Table of Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. Uncrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Check Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Install Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Secure Dash
Resumo do conteúdo contido na página número 4
Intermediate Frame Snowthrowers 1 (2) x 2 Size PSI bar 15 x 5.0-6 20 1,38 16 x 4.8-8 14 ,96 TP 300-4681-01-IW-SN 4 09/2007
Resumo do conteúdo contido na página número 5
Intermediate Frame Snowthrowers 3 B D A B C A D A C 5/16-18 x 2 5/16-18 B D 5/16-18 x 2-3/4 5/16 4 7 Nm 5 lb-ft 09/2007 5 TP 300-4681-01-IW-SN
Resumo do conteúdo contido na página número 6
Intermediate Frame Snowthrowers 5 B A 5/16-18 x 1-1/2 B 5/16-18 A 6 A D C B TP 300-4681-01-IW-SN 6 09/2007
Resumo do conteúdo contido na página número 7
Intermediate Frame Snowthrowers 7 1 1 2 2 3 8 9 09/2007 7 TP 300-4681-01-IW-SN
Resumo do conteúdo contido na página número 8
Intermediate Frame Snowthrowers 10 11 12 TP 300-4681-01-IW-SN 8 09/2007
Resumo do conteúdo contido na página número 9
Intermediate Frame Snowthrowers 14 13 15 16 09/2007 9 TP 300-4681-01-IW-SN
Resumo do conteúdo contido na página número 10
Intermediate Frame Snowthrowers Perform E F B Safety Checks A Check Engine Controls 1. Make sure all safety guards are in place and all nuts, C bolts, clips, cotter pins and wires are secure. 2. Check to make sure spark plug wire is attached. 3. Check all controls for proper operation: D a. The engine should stop when the key is removed. b. The throttle should control the engine speed and stop the engine when moved to the STOP position. G c. The fuel shut-off valve should stop the flow of fuel t
Resumo do conteúdo contido na página número 11
Intermediate Frame Snowthrowers Perform Safety Checks E Check Snowthrower Controls 1. Check the skid shoes to make sure they are set at the desired height. Adjust if necessary. 2. Check the traction drive control (B, Figure 2). Snowthrower motion should stop when the control is B released. C 3. Check the auger control (C). Auger movement should stop when the control is released. 4. Check the manual chute direction control (D) for prop- er operation. The discharge chute should rotate freely in
Resumo do conteúdo contido na página número 12
Intermediate Frame Snowthrowers A Auger Drive Adjustment D E WARNING Do not over-tighten, as this may lift the lever and cause auger drive to be engaged without depressing the Auger Control. F 1.With the drive lever released, the hook (B, Figure 3) should barely touch the lever (C) without raising it. There can be a maximum 1/32” clearance as shown. 1/32” (.8 mm) 2. To adjust, loosen nut (D) by holding the adjusting flats (A) and turning nut (D). Turn adjustment flats and hold screw. The adjus
Resumo do conteúdo contido na página número 13
Intermediate Frame Snowthrowers Run-In Adjustment WARNING ALL MODELS Do not over-tighten, as this may cause traction 1. After 5 hours of use, check for proper adjustment. drive to engage without depressing the traction Readjust clutch cable if necessary by increasing ten- drive control (arm must remain in down position). sion on cable. A small amount of arm movement is Verify that the cables are not over-tightened: With permissible if unit passes operating checks described speed selector in posi
Resumo do conteúdo contido na página número 14
Intermediate Frame Snowthrowers 7. Loosen shift lever nuts (B, Figure 6), and position the Scraper Bar & shift speed lever (A) in the lowest forward speed. Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be high enough so that it will not pick up gravel or debris. A The height of the scraper bar is controlled by raising or lowering the Skid Shoes (See Figure 8). B 1. To raise the sc
Resumo do conteúdo contido na página número 15
Intermediate Frame Snowthrowers Belt Adjustment Auger Drive Belt B If your snowthrower will not discharge snow, check the control cable adjustment. If it is correct, then check the condition of the auger drive belt. If it is damaged or loose,replace it (see Belt Replacement in this section of the manual). 1. Disconnect spark plug wire. 2. Loosen screw (B, Figure 9) from belt cover (A). Remove belt cover (A). B A 3. Loosen nut (D, Figure 10) on auger idler pulley (B) and move auger idler pulley
Resumo do conteúdo contido na página número 16
Intermediate Frame Snowthrowers Belt Replacement A B F Auger Drive Belt The drive belts are of special construction and must be C L replaced with original factory replacement belts available D from your nearest authorized service center. Some steps require the assistance of a second person. If the K auger drive belt is damaged, the snow thrower will not E discharge snow. Replace the damaged belt as follows. 1. Disconnect the spark plug wire. A 2. Loosen the capscrews (A, Figure 11) on each s
Resumo do conteúdo contido na página número 17
Intermediate Frame Snowthrowers B A A Figure 14. Rotator Shaft Removal A. Pin, Hair B. Shaft A C Figure 16. Chute and Rotator Removal A. Chute and Rotator B D A Figure 15. Offset Tube (Lower) Removal A. Nuts, KEPS, hex, 5/16-18 B. Bolts, Carriage, 5/16 x 1-1/2 C. Tube, Offset D. Bracket, tube support B 9. Remove hair pin (A, Figure 14) and slide rod (B) backward about 3 inches (until shaft separates from D C the worm drive). 10. Remove two 5/16-18 KEPS hex nuts (A, Figure 15), Figure 17. Frame a
Resumo do conteúdo contido na página número 18
Intermediate Frame Snowthrowers Traction Drive Belt If the snow thrower will not move forward, check the trac- tion drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows. 1. Disconnect the spark plug wire. 2. Remove the auger drive belt. See “Belt Replacement” in this section. 3. Remove the traction drive spring (E, Figure 12). B 4. Remove the e-ring (J, Figure 12) from one end of the swing plate axle rod (I). 5. Remove the swing plate axle rod
