Resumo do conteúdo contido na página número 1
USE AND CARE OF YOUR
™
My Café Automatic
Tea & Coffee Pod Brewer
P2955
Model MCAA
COMMERCIAL TYPE
The Bunn logo is a registered trademark of Bunn-O-Matic Corporation.
My Café is a trademark of Bunn-O-Matic Corporation.
RECORD MODEL & SERIAL NUMBER
In order to receive accurate and timely warranty assistance, it is important to
record the Model and Serial Number information located on the bottom of the
brewer. A space is provided below for this information.
MODEL: Record these numbers from th
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS WARNINGS ...........................................................................................................................2 USER NOTICES .....................................................................................................................3 INTRODUCTION ....................................................................................................................3 SPECIFICATIONS ......................................................................
Resumo do conteúdo contido na página número 3
USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices on the equipment should be kept in good condition. Replace any unreadable or damaged labels by visiting our web site at www.bunn.com. # 37280.0000 # 37281.0000 # 00656.0000 # 37267.0000 INTRODUCTION ® ™ The BUNN My Café Automatic Tea & Coffee Pod Brewer is designed to personalize your brewing experience by allowing a single cup brew of perfectly balanced
Resumo do conteúdo contido na página número 4
IMPORTANT SAFEGUARDS Follow these basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and/or personal injury: • Do not insert or remove pod holder while • Read all instructions. brewing. Press the coffee or tea button to • Do not touch hot surfaces. Use handles or stop or cancel a brew cycle. knobs. • A canceled brew cycle is not held in • To protect against electric shock, do not memory. The next brew cycle will place cord, plug, or brewer
Resumo do conteúdo contido na página número 5
GENERAL INFORMATION Improper installation could result in permanent damage and void the limited warranty. Read & follow instructions on page 9 or 10. ® • Use CAUTION when dispensing hot water from the brewer. The water from your BUNN Pod brewer is approximately 93°C (200°F). This is approximately 10°C (50°F) hotter than the hot water from your faucet and must be handled with care. • This brewer is designed to remain plugged in at all times (except during initial installation, cleaning, or wh
Resumo do conteúdo contido na página número 6
FEATURES & CONTROLS SLIDE LID WATER POD HOLDER RESERVOIR RELEASE BUTTON SPRAYHEAD SEAL SPRAYHEAD POD HOLDER INSERT POD HOLDER DRIP TRAY GRATE POWER SWITCH DRIP TRAY WATER INLET BLUE (BREW) LIGHTS VOLUME CONTROL CONTROL PANEL SLIDE LEVER P2956 FIG 1. Exploded View HEATING INDICATOR REFILL WATER POD HOLDER INDICATOR INDICATOR COFFEE BREW TEA BREW BUTTON* BUTTON* VOLUME CONTROL * The Coffee or Tea button can be pressed again to stop or cancel a brew cycle in process. INDICATORS P2957 FIG 2.
Resumo do conteúdo contido na página número 7
DEFINITIONS COMPONENTS • WATER RESERVOIR - Holds reserve water for brewing. The reservoir can be removed and filled separately at a sink or other clean water source or by pouring water through the slide lid. (Holds 1.7 L (46 oz.) to the maximum line.) • SLIDE LID - The slide lid allows access to the reservoir. Water can be poured through the opened lid and into the reservoir without removing the reservoir. • POD HOLDER RELEASE BUTTON - Push to unlock and release the pod holder. When there is
Resumo do conteúdo contido na página número 8
CONTROL PANEL (Cont.) • HEATING INDICATOR - This light indicates that the heater is bringing water up to temperature. A brew cycle cannot be started until the indicator has gone out. (During a brew cycle, this light will come on indicating the tank heater is warming the new water entering the tank.) • POD HOLDER INDICATOR - This indicator identifies a missing or unlocked pod holder. Before a brew cycle can be started, the pod holder must be inserted and locked into place. • TEA BREW BUTTON -
Resumo do conteúdo contido na página número 9
WATER INLET SET-UP ™ The My Café Automatic Pod Brewer is designed for businesses and office applications, where a pressurized water system can be utilized to feed the brewer with a constant water supply. If the machine will not be used with plumbing, proceed to the “Pour-Over” Section on page 12. IMPORTANT NOTE: If the brewer is to be used as a pour-over, the cap must be installed on the water inlet fitting, located in the rear of the brewer. (See FIG. 3) Otherwise, prepare the existing wate
Resumo do conteúdo contido na página número 10
“AUTOMATIC SECTION” INITIAL BREWER SET-UP For pour-over set-up, go to “Pour-Over Section” on page 12. 7. Place a mug or bowl that 1. Remove the lid and will hold at least 414 ml water reservoir. (14 fl. oz.) onto the drip tray grate. P2961 8. Press and release the coffee brew P3017 button to fill the (CAUTION: Do not place the brewer in reservoir with a sink or other water source.) water.* P2958 2. Thoroughly rinse the water reservoir. 9. Press and release the coffee brew button again
Resumo do conteúdo contido na página número 11
BREWING DELICIOUS COFFEE OR TEA WARNING: Never place hands directly under pod holder outlet. Hot water can be present. WARNING: Never remove the holder with force. If stuck, wait 10 minutes and try again. WARNING: Never brew without the pod holder insert in place. 1. Adjust the volume 5. Insert the loaded pod control lever to the holder into the brewer desired volume. and press all the way in to lock holder. (See page 14 for brewing tips) P2903 P2952 NOTE: Minimum volume is approx. 118 ml
Resumo do conteúdo contido na página número 12
“POUR-OVER SECTION” INITIAL BREWER SET-UP For Automatic set-up, go to “Automatic Section” on page 10. 7. Plug in the brewer 1. Remove the lid and and turn on the water reservoir. power switch. P0214/2960 8. Place a mug or bowl that P3017 will hold at least 414 ml (CAUTION: Do not place the brewer in (14 fl. oz.) onto the drip a sink or other water source.) tray grate. P2961 2. Thoroughly rinse the water reservoir. 9. Press and release the coffee brew 3. Fill the reservoir to the button
Resumo do conteúdo contido na página número 13
BREWING DELICIOUS COFFEE OR TEA WARNING: Never place hands directly under pod holder outlet. Hot water can be present. WARNING: Never remove the holder with force. If stuck, wait 10 minutes and try again. WARNING: Never brew without the pod holder insert in place. 1. Open the slide lid. 7. Press a pod into the pod holder. P2909 P2941 (NOTE: For best results, center pod in (CAUTION: Do not place brewer in sink or holder and gently press the pod completely other water source.) into holder cavi
Resumo do conteúdo contido na página número 14
HOT WATER The same basic steps used to brew coffee or tea can be used to obtain hot water by leaving the coffee pod or tea bag/pod out of the pod holder. ® CAUTION: The water from your BUNN Pod brewer is approximately 93°C (200°F). This is hotter than the hot water from your faucet and must be handled with care. COFFEE FUNDAMENTALS Brewing delicious coffee is similar to cooking any favorite food. Both require a good recipe. Proper coffee making requires quality equipment to precisely ® co
Resumo do conteúdo contido na página número 15
ROUTINE CLEANING Before beginning any cleaning procedure, unplug the brewer to avoid the accidental start of a brew cycle. Clean the pod holder, drip tray and drip tray grate after each use, using a damp cloth and mild detergent and rinse. With the pod holder and drip tray removed, use a damp cloth with mild detergent to wipe the area below the pod holder and into the drip tray area. Occasionally, wipe the outside of the brewer with a damp cloth. (The reservoir, slide lid, pod holder, dri
Resumo do conteúdo contido na página número 16
PERIODIC CLEANING/DESCALING (Cont.) 8) When the cycle has finished, empty the container. Repeat step 7 at least two more times to remove the solution from the tank. 9) Clean the pod holder with a mild detergent and rinse thoroughly. 10) Proceed to the “Cleaning The Sprayhead/Seal” section. CLEANING THE SPRAYHEAD/SEAL 1) Press the Power Switch into the off “O” position. 2) Unplug the brewer and allow it to cool down. (Minimum of 1 hour.) 3) After the unit has been allowed to cool, remove the pod
Resumo do conteúdo contido na página número 17
INSPECTING THE SPRAYHEAD SEAL When disassembling your brewer for cleaning, inspect the sprayhead seal for cracks, tears and holes. Although the seal should last for an extended period of time, damage can occur through handling. CAUTION: The seal confines the hot liquid to the pod holder. Replace the seal if it becomes damaged. Parts are available at www.bunn.com. CLEANING THE POD HOLDER To prevent residue build up, it is a good idea to periodically disassemble the pod holder/screen assembly
Resumo do conteúdo contido na página número 18
TROUBLESHOOTING SITUATION EXPLANATION Nothing happens when the This is the first time you have used your COFFEE BUTTON or TEA brewer. BUTTON is pressed. The Initial Brewer Set-up procedure must be performed first. Please follow the directions on page 10 (Automatic) or page 12 (Pour- Over) before attempting to run a brew cycle. Your brewer is not plugged in. Check to make sure the brewer is plugged in and the POWER SWITCH has been turned on. (The POD HOLDER RELEASE BUTTON - also known as the
Resumo do conteúdo contido na página número 19
SITUATION EXPLANATION The REFILL WATER INDICATOR Pour-Over only: has come on. The WATER RESERVOIR has run low on water. Slide the lid open and pour additional water into the reservoir, or remove the reservoir and fill it at a sink, or other water source. CAUTION: Do not place the brewer in a sink or other water source. Do not fill past the Maximum fill line. Automatic only: The WATER RESERVOIR has recently been removed from the brewer and replaced empty. Press the Coffee or Tea brew butto
Resumo do conteúdo contido na página número 20
TROUBLESHOOTING (Cont.) SITUATION EXPLANATION (Continued) again. This is normal and will take about 45 The water shuts off and comes seconds to complete. Wait for the blue lights back on again when brewing. to go out. NOTE: Although the pulse brew process can be used for coffee or tea, it is designed to brew tea. Because the process of brewing tea is different than coffee, the brewer works differently when the TEA BREW BUTTON is used. An “On-Off-On” cycle is used to steep the tea and p
