Resumo do conteúdo contido na página número 1
IMPORTANT MANUAL Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
PP10530ES
In struc tions. Fail ure to do so
can result in serious injury.
SNOW THROWER
Always Wear Eye Protection During Operation
421064 07.03.08 CL Printed in U.S.A.
Resumo do conteúdo contido na página número 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Resumo do conteúdo contido na página número 3
6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect chute is the most common cause of injury associated with the spark plug wire and keep the wire away from the snow throwers. Never use your hand to clean out the dis- plug to prevent someone from accidentally starting the charge chute.
Resumo do conteúdo contido na página número 4
PARTS PACKED SEPARATELY IN CARTON 4
Resumo do conteúdo contido na página número 5
ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product. Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as s
Resumo do conteúdo contido na página número 6
ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) (See Figs. 3 and 4) The auger control rod has the short loop on the end of the spring as shown. The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown. 2. W
Resumo do conteúdo contido na página número 7
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL INSTALL DISCHARGE CHUTE / CHUTE ROTATER (See Figs. 8 and 9) HEAD (See Fig. 7) 1. Install remote cable bracket to discharge chute with NOTE: The multi-wrench provided in your parts bag may 5/16-18 carriage bolt and 5/16-18 locknut as shown. be used to install the chute rotater head. Tighten securely. 1. Place discharge chute assembly on top of chute base 2. Install remote cable eyelet to chute deflector with with discharge open
Resumo do conteúdo contido na página número 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Resumo do conteúdo contido na página número 9
OPERATION SPARK ENGINE OIL CAP AUGER DISCHARGE CHUTE CONTROL LEVER PLUG WITH DIPSTICK CONTROL SAFETY LEVER TRACTION DRIVE SPEED IGNITION DRIVE CON TROL LEVER KEY CONTROL GAS O LINE LEVER FILLER CAP CHUTE CHOKE DE FLEC TOR CON- TROL FUEL SHUT-OFF LH TURN VALVE TRIGGER THROTTLE DEFLECTOR / ENGINE REMOTE CONTROL CONTROL DISCHARGE LEVER CHUTE RECOIL POWER LIGHT (AUXILIARY) CORD STARTER PLUG ELECTRIC HANDLE OIL DRAIN PLUG START HANDLE BUTTON CLEAN-OUT TOOL KNOB PRIM ER MUF
Resumo do conteúdo contido na página número 10
OPERATION The operation of any snow thrower can result TO USE CHOKE CON TROL (See Fig. 13) in foreign objects thrown into the eyes, which The choke con trol is located on the en gine. Use the choke can result in severe eye damage. Always wear control when ev er you are starting a cold en gine. Do not safety glasses or eye shields while operating use to start a warm en gine. your snow thrower or performing any ad just - • To engage choke, turn knob clockwise. Slowly turn ments or repairs.
Resumo do conteúdo contido na página número 11
OPERATION TO THROW SNOW (See Fig. 15) TO MOVE FORWARD AND BACKWARD (See Fig. 17) The auger rotation is controlled by the auger control lever SELF-PROPELLING, forward and reverse movement of located on the right side handle. the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Squeeze traction drive control lever to handle to en gage the drive system. • Release the aug
Resumo do conteúdo contido na página número 12
OPERATION BEFORE STARTING THE ENGINE TO ADJUST SKID PLATES (See Fig. 19) NOTE: The wrench provided in your parts bag may be CHECK ENGINE OIL LEVEL (See Fig. 20) used to adjust the skid plates. The engine on your snow thrower has been shipped, from Skid plates are located on each side of the auger housing the factory, already filled with oil. and adjust the clearance between the scraper bar and the 1. Check engine oil with snow thrower on level ground. ground surface. Adjust skid plates evenly
Resumo do conteúdo contido na página número 13
OPERATION TO START ENGINE 6. When the engine starts, release the recoil starter han dle and slowly move the choke control to the “OFF” posi- • Be sure fuel shut-off valve is in the “OPEN” position. tion. Your snow thrower engine is equipped with both a 120 Volt Allow the engine to warm up for a few minutes. Engine will A.C. electric starter and a recoil starter. The electric starter not develop full power until it has reached normal operat- is equipped with a three-wire power cord and plug
Resumo do conteúdo contido na página número 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items SAE 5W-30 Motor Oil that have been sub ject ed to operator abuse or negligence. To receive full value from the warranty, operator must See “ENGINE” in maintain snow thrower as in struct ed in this manual. Some Maintenance section ad just ments will need to be made periodically to properly maintain your snow thrower. General Purpose All adjustments in the Service and Ad ju
Resumo do conteúdo contido na página número 15
MAINTENANCE Check the crankcase oil level before starting the engine and SNOW THROWER after each five (5) hours of continuous use. Tighten oil fill Always observe safety rules when performing main te nance. cap / dipstick securely each time you check the oil level. TIRES TO CHANGE ENGINE OIL • Maintain proper air pressure in both tires (14–17 P .S.I. Determine temperature range anticipated before next oil / 19-24.5 N-m). change. All oil must meet API service classification SG–SL. • Keep tire
Resumo do conteúdo contido na página número 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to WARNING: To avoid serious injury, STOP position. Wait for all moving parts to stop. before performing any service or ad- 2. Remove safety ignition key and disconnect spark plug just ments: wire from spark plug. Place wire where it cannot come 1. Be sure throttle is in STOP position. in contact with plug. 2. Remove safety ignition key. 3. Align holes in impeller hub with holes in impeller shaft and install two (
Resumo do conteúdo contido na página número 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 23) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the “ON” position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced. It is recommended that the belt(s) be replaced to relieve tension. by a qualified service center. 8. With tension relieved on idler, install new traction drive belt around pulleys and ins
Resumo do conteúdo contido na página número 18
TO REMOVE WHEELS (See Fig. 24) NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts • Remove the klik pin and remove wheel from axle. dealer. Tire sealant also prevents tire dry rot and cor ro sion. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the ENGINE hole in the wheel hub (if equipped). Inner hole in axle and See engine manual. hole in wheel hub are not used fo
Resumo do conteúdo contido na página número 19
TROUBLESHOOTING See appropriate section in manual unless directed to a qualified service center. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position. 4. Move throttle to FAST position. 5. Choke in OFF position. 5. Move to FULL position. 6. Primer not depressed.
Resumo do conteúdo contido na página número 20
REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802) AUGER HOUSING / IMPELLER ASSEMBLY 5 11 11 6 7 15 16 14 12 8 13 11 4 17 12 3 11 10 1 9 2 33 32 34 30 31 31 26 36 29 28 20 27 21 22 23 25 35 24 23 22 2 (EXPLODED) 21 19 18 01.07.004-B 20
