Resumo do conteúdo contido na página número 1
Serious Steel
887101 LAT OPTION
I I
ASSEMBLY. INSTRUCTIONS "
Pan # 6802501
1
RmA.sion: 3/23/99
Resumo do conteúdo contido na página número 2
I IMpORTANT".NOTESI WELCOME TO THE WORLD OF ~t~il~$ ~t~t~! Please note: * Thank you for purchasing the Parabody 887101 LAT OPTION. Please read these instruction~ thoroughly and keep them for future reference. This product must be assembled on a flat, lev: surface to assure its proper function. We recommend cleaning your product (pads and flame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There i
Resumo do conteúdo contido na página número 3
PARTS LIST KEY PART# DESCRIPTION PART # DESC’R1PTION 6800203 1 UPRIGHT 1 ’20 ’623670’i 1-3/4" SQ. :END CAP 2 ~(X)602 ADJ FOOT SUPPOlZT 6412001 SPRING P ~ SEMBLY 3 6800803 PUI I .h’5[HOUSING 32033’01 VINYLCAP 1 22 4 6801003 TOP BOOM I 23 3/16X I-3N X 5-1/4" PLATE 5 6801102 LAT BAR SUPPORT" ’ 1 24 6416601 3/4’X 1-112" GLIDE 6759802 ~ARRIAGE 25 3102943 1/2X3 I/2" BOLT 1 6274402 LOW ROW BAR 3102502 m" sr~. 6725302 LAT BAR’ I 27 3102801 1/2" l ),UK.NUT 3-1/2" PUI 1 Fry 3116201 5 28 3102917 1/2 28 4"
Resumo do conteúdo contido na página número 4
LOWER CROSS SUPPORT 3/8" LOW HEIGHT LOCK N-U’T ~ FIGURE 2 STEP 2: NOTE: It may be necessar.~. to loosen the 1/2 X 3-1/4" BOLTS of the LOWER CROSS SUPPORT connecting the UPRIGHT ¯ FIL~.ME before beginning STEP 2. ¯ Attach four 314 X 1-1/T’ GLIDES (24) to the inside_ of the tube on the UPRIGHT (1) as sho~ in FIGURE 2 using tI~e follow- ~ng steps: Thoroughly clean all surfaces where the 3/4 X 1-1/2" GLIDES (24) are to be attached. ¯ "- Remo’,~ the 3/4 X 1 - 1/2" GL IDES ( 24 ) from the paper backin
Resumo do conteúdo contido na página número 5
FIGURE STEP 3: ¯ Insert two 2-1/2’ ROUND END CAPS (19) into the ends of the .ADJ. FOOT SUPPORT (2) as shown in FIGURE ¯ Insert one I-3/4" ENiD CAP (20) into the end ofthe ADJ. FOOT SUPPORT (2) as shown in FIGURE ¯ Apply m’o 2-1/2 X 5-1/2" NON-SKID STRIPS (18) to the ADJ. FOOT SUPPOKI" (2) as sho~n in FIGL~q.E ¯ Attach four 3/4 X 1-I/2" GLIDES (24) to the outside of the .4~DJ FOOT SUPPORT (2) and four GLIDES to the inside of the tube on the UPRIGHT (1) as showrt in FIGURE 3 using the follo~ng
Resumo do conteúdo contido na página número 6
// FIGURE 4 STEP 4: ¯ Attach eight 1X 1" GLIDES (15) to the ends the CARRIAGE (6) as sho~l in FIGURE 4 using the follo~4ng steps: ¯ Thorougltly clean Ml surfaces where the 1 X 1" GLIDES (15) are to be attached. ¯ Remove the 1 X 1" GLIDES (15) from the paper backing and firmly apply" them to all sho~-n surfaces. ¯ Attach one 1-1/4" SQ. RUBBER BUN~PER (17) to the underside of the angle on the CAP,~AGE (6) as shown in FIGURE FIGURE STEP 5: ¯ CAREFULLY slidethe CARRIAGE (6) over the UPRIGHT (1) as
Resumo do conteúdo contido na página número 7
FIGURE 6 l/2 X 4" SUPPORT STEP 6: ¯ NOTE: It may be necessary to loosen the 1/2 X 3-1/4" BOLTS of the UPPER CROSS SUPPORT connecting the UPRIGITr FRAME before beginningSTEP 6. ¯ LOOSELY assemble the TOP BOOM (4) to the UPKIGHT (1) using one 1/2 X 4" BOLT (28), one 112 X 3-1/2" BOLT (25), " 97 ~VASHERS (26), and one 1/2 LOCK NL-I-S (.,) as sho~t in FIGURE ¯ LOOSELY assemble the TOP BOOM (4) to the UPPER CROSS SUPPORT using t~vo 3/8 X 4" BOLTS (38).~ four 3/8"’ WASHERS and two 318" LOCK NUTS (3
Resumo do conteúdo contido na página número 8
FIGURE 8 3/8 x STEP 8: ¯ Routethe 115-1/4" CABLE (l l) through the TOP BOOM (4) as sho~vn in FIGURE ¯ SECL’RELY assemble three 3-1/2"" PI]LI EYS (9) into the slots of the TOP BOOM (4) using three 3/8 X 2-3/4" BOLTS (32), six SPACERS (33), and three 3/8" LOCK N~’TS (31) as sho~.n in FIGLrRE 8. (NOTE: Make sure the cable is routed over "all the pulleys.)
Resumo do conteúdo contido na página número 9
FIGURE 9 STEP 9: ¯ Attach the CABLE (11) from the TOP BOOM (4) to the CARRIAGE (6) using one 1/4" QUICK LINK (36) as shm~al FIG URE 9. (I/~[PORTAN-~. Secure lighten QUICKLINK.) b" ¯ Place one 3-1/2" pLrLLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the ~FOP BOOM (4) as in FIGURE 9. LOOSELY assemble two 3/16 X 1-3/4 X 5-1/4" PLATES (23) to each side of the 3-1/2" PULLEY (9) using one 318 X 2" BOLT (35), two 318" WASI-IERS (30), and one 3/8" LOCK NUT (31). See FIGU
Resumo do conteúdo contido na página número 10
FIGURE 10 STEP 10: Route the threaded end of the 121-3/4" CABLE (12) through the slot oft.he PULLEY HOUSING then SECURELY assemble one 4-1/2 pLrLLEY (10) to the PU~.I.EY HOUSLNG (3) using t~vo 3/8X 2-3/4"" BOLTS (32), two 3/8"" FLANGE SPACERS (.: 3), two 3/8"" \\:-kSHERS (30), and two 3/8" LOCK NUTS (31). (NOTE: CABL E (12)should be routed benve en the pulle y and the retai ning bolt as shown FIGURE 10.) 10
Resumo do conteúdo contido na página número 11
THREADED END FIGURE 11 Q/ STEP 11: Loop the 121-3/4"" CABLE (12) around one 3-1/2" PULLEY (9) as shown in FIGURE ¯ LOOSELY assemble the 3-1/2" PUI JI.EY (9) to the 3/16 X 1-3/4 X 5-1/4" PLATES (23) using one 3/8 X 2" BOLT (35), mo 3/8" V¢.~SI-IERS (30), and one 3/8" LOCK NUT (31). See FIGLrRE 11. ¯ SECURELY thrend the end of the 121-3/4" CABLE (12) 3/4 of the way into .into the threaded housing on tile UPRIGHT and SF.,- CURELY tight~j~im rm~_ ....... . ...... ¯ . ¯ ~ ¯ SECURELY tightenthe two
Resumo do conteúdo contido na página número 12
i! / /i / I! /,,il/ l FIGURE 12 STEP 12: ¯ Slide t~vo 1 XS" GRI~PS (14) onthe LOWROWBAR(7) and t~vo 1X 8" GR~S (14) onthe LAT BAR (8) as sho~vnin FIGURE ¯ Attach the LAT BAR (8) to the ball end of the upper CABLE (11) using one 5/16"’ SNAP HOOK (34) as shown in FIGURE ¯ Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (12) using one 12-LINK CHAIN (37) and t~vo 5/16" SNAP (34) as shosx~ i~ FIGURE 12. Thank you for purchasing the Parabody 887101 LAT OPTION~.If unsure ofproper use o
