Manual do usuário ParaBody 701

Resumo do conteúdo contido na página número 1

701
PARABODY 525 PEC DEC OPTION
PRODUCT ASSEMBLY
INSTRUCTIONS SHEETS
REV1SI:ON C

Resumo do conteúdo contido na página número 2

! ! ! ATTENTION ! ! ! UNLESS__O_T_HER~ C_~NNE~ _CAg_NSJS_T~F ONE LD BO_L Z’~ ~HERS, AND ONE (,O_LO~K..N_U_T,_ BOLT.

Resumo do conteúdo contido na página número 3

701 FACTOR 525 PEC DEC ATT. ASSEMBLY PARTS LIST (LEVEL 1) SORT AND COI.£NT ALL PARTS BEFORE BEGINNING ASSEMBLY ITEM NAME/DESCRIPTION QTY I/2 X 4-I/2 IN. BOLT ............................................................................................................ 2 2. 3/8 X 2 IN. BOLT .................................................................................................................. 2 3. 3/4 IN. WASHER ............................................................................

Resumo do conteúdo contido na página número 4

701 FACTOR 525 PEC DEC ATT. ASSEMBLY PARTS LIST (ZEVEL 2) SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY HARDWARE." ITEM NAME/DESCRIPTION QTY 1 3/8 X 2 IN. BOLT .................................................................................................................. I 2. 3/8 X i-314 IN. BOLT ............................................................................................................. 3. 3/8 IN. WASHER ..................................................................

Resumo do conteúdo contido na página número 5

COTTERLE~ HITCH PIN LEFT PEC DEC 0 2 SO. END CAP (4) RIGHTPEC DEC ARM I~Y BRACKET 3/4 IN. WASHER (2) LEFT ARM A[ RIGHT ARM AE "-. /-- .CAM STOP ~ ~ CARRIAGE GUIDES (2) 1 . // // ~ ~ / ~i/2 X 4 I/2 IN BOLT (2) , , ~ / 3/4 LD. STAR~OCK COL~ (2) / ~2 SQ. END C~ (2) ~ ~ P~BODY I~C- ~ AS~ INST. 70

Resumo do conteúdo contido na página número 6

FACTOR 525 PEC DEC ATT. ASSEMBLY INSTRUCTIONS (LEVEL 1) ,--. ~01 IF THE SHROUD IS ASSEMBLED TO THE FACTOR 525, IT WILL NEED TO BE REMOVED NOTE: TO ASSEMBLE THE PEC DEC A’vrACHMENT. PLEASE REMOVE THE SHROUD AT TH][S TIME BY CAREFULLY REMOVING TIlE FOURTEEN (14) SHROUD FASTENERS. Insert two (2) 2 IN. SQ. END CAPS into both ends of the BEARING HOUSING, as shown on drawing. SECURELY assemble the BEARING HOUSING and the CENTER PULLEY BRACKET to the FRONT UPRIGHT as shown on drawing, using two (2) I/2

Resumo do conteúdo contido na página número 7

FACTOR 525 PEC DEC ATT. ASSEMBLY INSTRUCTIONS (LEVEL 2) --. LOOSEN the 3/8 X 4 IN. BOLT that assembles the two (2) PULLEYS, and two (2) 1/2 IN. SPACEP, the BASE directly behind the FRONT UPRIGHT. Remove the 3/$ IN. LOCK NUT, and the 3/g IN. WASHER. Slide the BOLT out enough to remove the two (2) I/2 IN. SPACERS. Replace the 1/9- IN. SPACERS with one (1) 4-I/2. X 1 IN. PULLEY, as shown in (VIEW B-B). Slide BOLT back Replace the 3/8 IN. WASHER, and .3/8 IN. NUT. TIGHTEN CONNECTION SECURELY. SECU

Resumo do conteúdo contido na página número 8

(LEVEL 701 FACTOR 525 PEC DEC ATT. ASSEMBLY INSTRUCTIONS The D-RING CABLE CLIP on the end of the LINK CABLE should rcstjust above the D-RING. If the LINK CABLE seems to be pulling on the D-RING or is resting too far above the D-RING, adjust it by raising or lowering the two (2) 1/4-25 lN. NUTS that attaches the LINK CABLE to the PULLEY BRACKET. When the correct height is obtained SECURELY tighten the two (2) 1/4-28 NUTS together around the PULLEY BRACKET. To adjust the pre-stretch on the PEC DEC

Resumo do conteúdo contido na página número 9

FRONT OF I~,CHINE ~EE VIEW C-C D SEE DET~,IL A ~SHROUD ...C~.SEE VIEW F-F) / f LIN.__~K_~ABLZ / i SHOCK CC ! SEE D~I’AIL F--~ o ; L-PIN

Resumo do conteúdo contido na página número 10

FRONT OF MACHINE ~--D-RING CABL~ CtJP ~ LEG CURL/~ION AB CRUNCH CABLE l o ._A VIEW B~B r- D-R~NG $HROUI~ FA_RI’ZNERS (I 4.) ~ FRONT OF MACHINE ~o MIDDLE U PRIGF,’r ~ ~ SHROUD VIEW F-F DETAIL C-C VIEW D-D FACTOR 525 PEC DEC~