Manual do usuário ParaBody 503

Resumo do conteúdo contido na página número 1

EX500 PEC DEC ATTACHMENT
503
II
PRODUCT-ASSEMBLY
INSTRUCTION SHEETS
TOOLS REQUIRED FOR ASSEMBLY:
9/16 INCH SOCKET
1/2 INCH SOCKET
ADJUSTABLE ~,VRENCH
HAMMER or RUBBER MA.LLET
REVISION: M ..
...-_...=.,:::. :.: -:.:-: !.: ~i"-£~ .::".
If you experience any problems with the assembly of this product, please contact .. .. ....
.
. .... ~ , ,, ::~_. ...-.- r ~ .,,=-r .~,~ ~-.’~~:~
)’our dealer or your PARABODY CuStomer Service representative at::_~ ._.~--- _~:~ r_~ ~’ - : ;
.:L ~ ’::.. ~ .~=’.--:-:

Resumo do conteúdo contido na página número 2

"" " 503 EXS00 PEC DEC ATTACHMENT ASSEMBLYPARTS LIST FOR STEP #1 & #2 SORT A~ND COUNT ALL PARTSBEFORE BEGINNING ASSEMBLY IJARDWARE: QTY ITEM NAME/DESCRIPTION. : ................................ 3 .3/8 X 1-3!4 BOLT ................................................................................... 2 3/8 X 2-3/4 BOLT ...................................................... .............................................................. 2. ~ " 4 3/8 X 3 BOLT 3. " 2 3/8 X 3-I/4 BOLT 4. 2 STAR LOCK COLL

Resumo do conteúdo contido na página número 3

503 EXS00 PEC DEC ATTACHMENT ASSEMBLY PARTS LIST FOR~~ STEP #1 & #2 ........ : ...... : .... SORT AND COU]N’T ALL PA~RTS BEFORE BEGINNING ASSEMBLY..... ~;WWEL PULLEY HARDWARE/PARTS: ITEM NAME/DESCRIPTION " ~ii QTY’-.. 3/8 X 3/4 BOLT ........................................................................ 2. 5/16 WASHER. ....... : ......................................... ~ .............................. : ............................ ~,..~ ......2 " ’ 3. 3/8 LOW HEIGHT LOCK NUT " 1 4. 3/8 WASHER

Resumo do conteúdo contido na página número 4

Carefully place the BEARING HOUSING and the BACK SUPPORT FRAME on the floor ~nd loosely assemble them together before attaching them to the REAR RIGHT UPRIGHT, using one (1) 318 X BOLT, two (2) 3/8 WASHERS, one (I) 3/8 LOCK WASHER, and one (1) 3/8 Insert one (1) 2 IN SQ. END CAP into the end of the PULLEY BRA~CKET SUPPORT. Loosely assemble the BEARING HOUSING/BACK SUPPORT. FRAME ASSEMBLY,and the PULLEY BRACKET SUPPORT to the EX500 BASE UNIT’S REAR RIGHT :UPRIGHT CONNECTION POINTS #1 and #2, us

Resumo do conteúdo contido na página número 5

503 EXS00 PEC DEC ATTACHMENT ASSEMBLYINSTRU~’iONS (STEP #1) Attach eight ($) PARAGLIDE STRIPS to the BACK SUPPORT FRAME as shown in DETAIL on (STEP #I SHEET #I of#2), using the following steps: A. ThoroughIy clean all inside and outside surfaces where the PARAGLIDE STR/PS ~a’¢ to b¢ attached. B. Remove the paper backing from the PARAGLIDE STRIPS AND FIRMLY APPLY them to all of the shown surfaces. (8 places) Assemble the SPRING PIN ASSEMBLY on the BACK SUPPORT FRAME~ u~ing on(." (i) PLUNGER, 13.

Resumo do conteúdo contido na página número 6

EXS00 PEG DEC ATTACHMENT A~5~.E_M.J:$LY-I~STR.UL’I’IO~NS 503 ..... ~.I-~ ¯ ¯ (STEe #2) THE ~RU~IONS FOR ~EP ~2 ARk T0 BE USED’WITH D~G SHEET ~! OF Loosely ~cmble one (I) 3/8 DIA. X 1 IN. LG. BUSH~G PULLEY ~d 0n~ (1) CABLE 1. CL~ to ~e PULLEY FLAT on ~e WEIGHT STACK S~PORT BASE, (CON~ION PO~ #3), using one (1) 3/8 X 1-3/4 BOLT, one (1) 3/8 LOCK WASHE~ ~d one (1) 3/8 ~. (SEE A). ASSEMBLE ~e SWIVEL PULLEY B~C~TS using (1) 3/8 DIA x 3/4 BOLT, (2) ~/16 WAS~, 2. (1) 3/8 WASHER ~d (1) 3/8 LOCK NUT. ~

Resumo do conteúdo contido na página número 7

... 0.1 ul I ! I ,,I V- 0 ! I.d \ I" X I ’1’

Resumo do conteúdo contido na página número 8

/ \, ! I IlO, ¯ ~ C r,