Resumo do conteúdo contido na página número 1
Cordless Jig Saw
MODEL 4331D
MODEL 4333D
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Resumo do conteúdo contido na página número 2
SPECIFICATIONS Model 4331D 4333D Length of stroke 26 mm (1”) Wood 65 mm (2-1/4”) Max. cutting capacities Mild steel 10 mm (3/8”) Aluminum 20 mm (13/16”) Strokes per minute 500 - 2,800/min Overall length 280 mm (11”) Net weight 2.6 kg (5.7 lbs) 2.9 kg (6.3 lbs) Battery Cartridge Voltage Battery Charger Input Output Charging time 1222 45 min. 1234 12 V 60 min. 1235 70 min. A. C. only D.C. DC1414 50 Hz - 60 Hz 7.2 V - 14.4 V 1422 45 min. 1434 14.4 V 60 min. 1435 70 min. • Manufacturer reserves the
Resumo do conteúdo contido na página número 3
9. Remove adjusting keys or wrenches Work Area before turning the tool on. A wrench or a 1. Keep your work area clean and well lit. key that is left attached to a rotating part of Cluttered benches and dark areas invite acci- the tool may result in personal injury. dents. 10. Do not overreach. Keep proper footing 2. Do not operate power tools in explosive and balance at all times. Proper footing and atmospheres, such as in the presence of balance enable better control of the tool in flammable li
Resumo do conteúdo contido na página número 4
18. Maintain tools with care. Keep cutting one tool may create a risk of injury when tools sharp and clean. Properly maintained used on another tool. tools with sharp cutting edge are less likely to SERVICE bind and are easier to control. 21. Tool service must be performed only by 19. Check for misalignment or binding of qualified repair personnel. Service or main- moving parts, breakage of parts, and any tenance performed by unqualified personnel other condition that may affect the tool’s may r
Resumo do conteúdo contido na página número 5
14. Some material contains chemicals which dust inhalation and skin contact. Follow may be toxic. Take caution to prevent material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD301-1 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ ................... direct current .../min................revoluti
Resumo do conteúdo contido na página número 6
7. Make sure cord is located so that it will a. That pins on plug of extension cord not be stepped on, tripped over, or other- are the same number, size, and shape wise subjected to damage or stress. as those of plug on charger; 8. An extension cord should not be used b. That extension cord is properly wired unless absolutely necessary. Use of and in good electrical condition; improper extension cord could result in a c. That wire size is at least as large as risk of fire and electric shock. If
Resumo do conteúdo contido na página número 7
(1) Do not touch the terminals with any 6. Do not store the tool and Battery Car- conductive material. tridge in locations where the temperature may reach or exceed 50°C (122°F). (2) Avoid storing battery cartridge in a container with other metal objects 7. Do not incinerate the Battery Cartridge such as nails, coins, etc. even if it is severely damaged or is com- pletely worn out. The battery cartridge can (3) Do not expose battery cartridge to explode in a fire. water or rain. 8. Be careful no
Resumo do conteúdo contido na página número 8
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 002702 Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. 12 • To insert the battery cartridge, align the tongue on the battery cartridge w
Resumo do conteúdo contido na página número 9
NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • If you charge a battery cartridge fro
Resumo do conteúdo contido na página número 10
002705 Selecting the cutting action This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action thrusts 1 the blade forward on the cutting stroke and greatly increases cutting speed. To change the cutting action, just turn the cutting action changing lever to the desired cutting action position. Refer to the table to select the appropriate cutting action. 1. Cutting action changing lever 002788 Position Cutting action Applications For cut
Resumo do conteúdo contido na página número 11
002790 Workpiece to be cut Number on adjusting dial Wood 3 - 5 Mild steel 3 - 5 Stainless steel 3 - 4 Aluminum 2 - 3 Plastics 1 - 4 CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up. • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge
Resumo do conteúdo contido na página número 12
002718 With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller. Then tighten the screw clock- wise to secure the blade. 1 2 To remove the blade, follow the installation procedure in reverse. 3 NOTE: 1. Screw • Occasionally lubricate the roller. 2. Roller 3. Jig saw blade 002725 Installing the universal shank jig saw blade If the universal blade clamp is used, you can use blades of 6.35mm(1/4”
Resumo do conteúdo contido na página número 13
002735 Plastic base plate (optional accessory) Use the plastic base plate when cutting decorative veneers, 1 plastics, etc. It protects sensitive surfaces from damage. To 2 replace the base plate, remove the four screws. 3 1. Screw 2. Plastic base plate 3. Hex wrench 002737 Rip fence (optional accessory) When cutting widths of under 150 mm (5 - 29/32”) repeat- edly, use of the rip fence (guide rule) will assure fast, clean, 1 straight cuts. To install it, loosen the bolt on the front of the base
Resumo do conteúdo contido na página número 14
002741 To attach the vacuum head on the tool, insert the hooks of the vacuum head into the hole in the base. The vacuum head 1 can be installed on either left or right side of the base. Then connect a Makita vacuum cleaner to the vacuum head. 2 1. Vacuum head 2. Base 002742 OPERATION CAUTION: • Always hold the base flush with the workpiece. Failure to do so may cause blade breakage, resulting in a serious injury. • Advance the tool very slowly when cutting curves or scrolling. Forcing the tool m
Resumo do conteúdo contido na página número 15
002751 Bevel cutting CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before tilting the base. With the base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). 002752 Loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the cross-shaped slot in the base. 2 3 1 1. Cross-shaped slot 2. Hex wrench 3. Bolt 002753 Tilt the base until the desired bevel angle i
Resumo do conteúdo contido na página número 16
Cutouts Cutouts can be made with either of two methods A or B. 002763 A) Boring a starting hole For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm (1/2”) or more in diameter. Insert the blade into this hole to start your cut. 1 1. Starting hole 002764 B) Plunge cutting You need not bore a starting hole or make a lead-in cut if you carefully do as follows. (1) Tilt the tool up on the front edge of the base with the blade point positioned just above the workpi
Resumo do conteúdo contido na página número 17
MAINTENANCE CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. 1 1. Limit mark 002785 Use a screwdriver to remove the b
Resumo do conteúdo contido na página número 18
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Jig saw blades • Various type of Makita genuine batteries and chargers • Hex wrench 3 • Rip fence (guide rule)
Resumo do conteúdo contido na página número 19
Memo 19
Resumo do conteúdo contido na página número 20
Memo 20
