Manual do usuário Newcon Optik LAM 10M IR

Manual para o dispositivo Newcon Optik LAM 10M IR

Dispositivo: Newcon Optik LAM 10M IR
Categoria: Apontador laser
Fabricante: Newcon Optik
Tamanho: 0.35 MB
Data de adição: 11/1/2014
Número de páginas: 24
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Newcon Optik LAM 10M IR. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Newcon Optik LAM 10M IR.

Para sua conveniência

Se a consulta dos manuais Newcon Optik LAM 10M IR diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Newcon Optik LAM 10M IR no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Newcon Optik LAM 10M IR em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Newcon Optik LAM 10M IR Manual de instruções - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Newcon Optik LAM 10M IR, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Newcon Optik LAM 10M IR. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1



Operation Manual











LAM 10M IR
LASER AIMING MODULE /
TARGET POINTER
105 Sparks Ave., Toronto, ON, M2H 2S5, Canada

Resumo do conteúdo contido na página número 2

Resumo do conteúdo contido na página número 3

IMPORTANT INFORMATION Read prior to activation You have just purchased a sophisticated electronic device. To operate it properly, please read this manual carefully. LAM belongs to Class I laser products in accordance with IEC 60825-1. Here are some common precautions that must be observed. • ALWAYS turn the device off when it is not in use and when you change the battery! • NEVER look into the beam • NEVER subject LAM to excessive impacts • NEVER transport LAM without the case • NEV

Resumo do conteúdo contido na página número 4

CONTENTS 1. Brief description ................................................. 2 2. Device design ..................................................... 3 3. DELIVERY SET ................................................ 8 3.1. Standard delivery set...................................... 8 3.2. Optional parts................................................. 8 4. Specifications...................................................... 9 5. OPERATION INSTRUCTIONS...................... 10 5.1. In

Resumo do conteúdo contido na página número 5

Carefully read all the instructions prior to use. Failure to obey the instructions will void the warranty! INVISIBLE LASER RADIATION CLASS I LASER PRODUCT 830–860 nm 0,1mW. 1. Brief description LAM 10M IR laser aimer (hereinafter referred as LAM) is designed for precise aiming at night time. LAM forms an IR laser radiation spot on the target visible only through the night vision goggles. It can be attached to a weapon equipped with Picatinny rail MIL-STD-1913. Laser beam, created b

Resumo do conteúdo contido na página número 6

2. Device design 1 2 3 4 5 6 7 8 17 16 14 3

Resumo do conteúdo contido na página número 7

9 10 11 12 14 13 Fig. 1. LAM 10M IR 1 – clamp 2 – bracket 3 – stopper 4 – remote connector 5 – body 6 – emitter 7 – emitter cap 8 – emitter protective cap 9 – windage adjustment 10 – fastener 11 – ‘laser on’ warning 12 – elevation adjustment indicator 13 – fixation screw cap 14 – fixation screw 15 – battery compartment 16 – battery compartment cap 17 – operating modes switch 4

Resumo do conteúdo contido na página número 8

LAM consists of an emitter (6,7, Fig.1), a battery compartment (15,16, Fig.1), windage (9, Fig.1) and elevation (12, Fig.1) adjustment mechanisms, an operating modes switch (17, Fig.1), a remote switch (Fig.2), a clamp (1, Fig.1). A battery is to be inserted into the battery compartment (16, Fig.1). Battery compartment cap (15, Fig.1) is attached to the body with a rubber band. The battery compartment is sealed with rubber O-ring. A spare O-Ring is included in the delivery set. Emit

Resumo do conteúdo contido na página número 9

LAM automatically turns off after 30 minutes of being switched in positions C and R. In order to activate LAM after it has automatically turned off, return the switch (17, Fig.1) into OFF position and then switch it to the desired position again. The remote switch (Fig.2) can be attached to LAM by a connector (3, Fig.2) with a union nut. When not in operation the connector (4, Fig. 1) is covered with a cap. The remote switch key (1, Fig.2) is attached to weapon pivot or grip with velcro

Resumo do conteúdo contido na página número 10

1 3 2 1 — key; 2 — velcro tape; 3 — connector Fig. 2. Remote switch 7

Resumo do conteúdo contido na página número 11

3. DELIVERY SET 3.1. Standard delivery set LAM is supplied in the following assembly: Quantity, pcs LAM 10M IR 1 Remote switch 1 Velcro tape 2 O-Ring 1 Case 1 Manual 1 Battery CR123 1 3.2. Optional parts LAM can be supplied with a barrel mount. 8

Resumo do conteúdo contido na página número 12

4. Specifications Laser wavelength 830…850 nm Beam divergence 0.5 mrad Spot size at 50 meters 25 mm Windage and elevation adjustment range ±20 mrad Windage and elevation adjustment step 0.5 mrad (50 mm @100m) Accuracy of adjustment after 1000 shots 0.1 mrad Accuracy of adjustment after 100 re- 1 mrad mountings on a rail Laser emitting power 0.1 mW Illumination distance 200 m Voltage 3 V Battery type CR 123 Battery life 30 hours Operating temperature range -40 °C …+60 °C Mount

Resumo do conteúdo contido na página número 13

5. OPERATION INSTRUCTIONS 5.1. Installing the battery LAM is powered by a standard Lithium CR123 3V battery. To install a battery: - unscrew the battery compartment cap (15, Fig.1), - insert a battery observing the polarity as marked on the battery compartment, - check the condition of the O-ring on the body; replace it if worn or torn, - screw the battery compartment cap back on. 5.2. Mounting LAM on a weapon LAM is mounted on a Picatinny rail in the following order: - loosen scre

Resumo do conteúdo contido na página número 14

5.3. Connecting the remote control To connect the remote switch (Fig.2): - unscrew the cap of the remote connector (4, Fig.1) and store it in a safe place, - plug in the remote connector contact (3, Fig.2) observing the key visible on the cable side, - tighten the union nut, - attach the remote switch to the weapon pivot or grip with velcro tape (2, Fig.2). 5.4. Adjusting LAM on a weapon Prior to adjusting LAM which has never been in operation, perform 10 shots in order to stabiliz

Resumo do conteúdo contido na página número 15

- remove protective cap (8, Fig. 1) from emitter tube output window; - activate LAM in mode C; - match the center of radiation spot with the aiming mark by means of rotating handwheels of adjustment mechanisms; - perform test firing with LAM under the same conditions as when checking the weapon fire capability with an iron sight; - eliminate deviation of the center of impact from the aiming mark. Deviation is measured by adjustment steps: each click of adjustment mechanism corresponds

Resumo do conteúdo contido na página número 16

6. Maintenance, storage and transportation 6.1. General LAM is a sophisticated precise optical instrument equipped with electronics. Therefore, it should be handled with due care. - Never disassemble LAM. - Keep away from direct sunlight, impacts, dust, moisture, and sharp changes of temperature. o - Do not keep LAM at temperatures higher than 60 C o (140 F). Keep away from heating appliances and central heating. - Do not touch the optical surfaces with fingers. Doing so may damage

Resumo do conteúdo contido na página número 17

6.2. Storage To set LAM from combat position into a stowed one: - turn LAM off (operating modes switch (17, Fig.1) should be set to OFF position); - cover emitter tube output window with protective cap (8, Fig.1); - disconnect remote switch (Fig.2) from the weapon, loosen screw caps (13, Fig.1), remove LAM with remote switch from Picatinny rail and place it into the case. LAM in the original packing should be stored in heated premises within the temperature range from +5 to +40° С, re

Resumo do conteúdo contido na página número 18

To apply new layer of lubricant: - Within two hours from cleaning apply an even 0.2-0.5 mm thick layer of lubricant on metal surfaces with a brush. - Do not cover plastic parts. When preparing for a long-term storage LAM just received from manufacturer or from workshop, ensure that actual set is the same as indicated in the Delivery Set section of this manual. Cases with LAMs should be placed on stands, shelves or in cupboards at dry heated and ventilated premises in accordance with

Resumo do conteúdo contido na página número 19

- Cover aimer with protective cap. - Disconnect the remote switch from the weapon. - Dismount LAM from Picatinny rail. - Pack LAM and remote switch into the case. When packed, LAMs can be transported by any covered means in accordance with storage conditions as described in this manual. When in operation, LAM is to be transported in its case or mounted on a weapon. 16

Resumo do conteúdo contido na página número 20

7. TROUBLESHOOTING Spot shape or size has changed Emitter objective lens is dirty. Flush emitter lens with fresh water and wipe it with soft cloth. No radiation when activating LAM with remote switch Turn the operating modes switch (17, Fig.1) to OFF position and then turn LAM ON again. If this doesn’t help, replace the remote switch. Radiation doesn’t stop when remote switch is released Replace the remote switch. Moisture in the battery compartment. Check the O-ring on the battery


Manuais similares
# Manual do usuário Categoria Baixar
1 American DJ IMAGE 8 DMX Manual de instruções Apontador laser 1
2 Barco R5900008_00 Manual de instruções Apontador laser 18
3 Barco 26-0405000-00 Manual de instruções Apontador laser 1
4 Black & Decker 90529709 Manual de instruções Apontador laser 3
5 Black & Decker LP001B Manual de instruções Apontador laser 0
6 Black Box LES424A Manual de instruções Apontador laser 1
7 Black Box 1-, 2-, and 4-Port Hardened Serial Servers Manual de instruções Apontador laser 1
8 Black Box LES422A Manual de instruções Apontador laser 1
9 Black Box LES421A Manual de instruções Apontador laser 5
10 Bushnell 201916 201921C Manual de instruções Apontador laser 2
11 Bushnell 740100 Manual de instruções Apontador laser 21
12 Califone LP2 Manual de instruções Apontador laser 0
13 Bosch Power Tools GPLL5 Manual de instruções Apontador laser 4
14 Canon I-Sensys Colour Laser Printer LBP5050 Manual de instruções Apontador laser 496
15 Casio YA-P10 Manual de instruções Apontador laser 1