Resumo do conteúdo contido na página número 1
Breaker Hammer
MODEL HM1800
002884
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Resumo do conteúdo contido na página número 2
SPECIFICATIONS Model HM1800 Blows per minute 1,000 Overall length 818 mm (32-1/4”) Net weight 29.1 kg (64 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Electrical Safety
Resumo do conteúdo contido na página número 3
6. Do not expose power tools to rain or wet Tool Use and Care conditions. Water entering a power tool will 15. Use clamps or other practical way to increase the risk of electric shock. secure and support the workpiece to a 7. Do not abuse the cord. Never use the cord stable platform. Holding the work by hand or to carry the tools or pull the plug from an against your body is unstable and may lead outlet. Keep cord away from heat, oil, to loss of control. sharp edges or moving parts. Replace 16.
Resumo do conteúdo contido na página número 4
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
Resumo do conteúdo contido na página número 5
7. Always be sure you have a firm footing. 12. Do not touch the bit or parts close to the Be sure no one is below when using the bit immediately after operation; they may tool in high locations. be extremely hot and could burn your skin. 8. Hold the tool firmly with both hands. 13. Some material contains chemicals which 9. Keep hands away from moving parts. may be toxic. Take caution to prevent dust 10. Do not leave the tool running. Operate the inhalation and skin contact. Follow mate- tool onl
Resumo do conteúdo contido na página número 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002892 Switch action 1 CAUTION: Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the “OFF” position when released. To start the tool, simply squeeze the switch lever. Release the switch lever to stop. 1. Switch lever ASSEMBLY CAUTION: Always be sure that the tool is switched off and unplugged be
Resumo do conteúdo contido na página número 7
CAUTION: Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure. (2) For bits without a collar 002931 1 2 34 5 Fig.(2) 1. Notched portion 2. Tool retainer shaft 3. Cylinder 4. When the bit is inserted 5. When the bit is retained Pivot the tool retainer front and slightly downward. With the notched portion of the bit facing the tool retainer shaft, insert the bit into the tool holder as far as it will go. Then pi
Resumo do conteúdo contido na página número 8
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001146 Replacing carbon brushes When the resin insulating tip inside the carbon brush is 2 exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should 1 be replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at 3 the same time. Use only ide
Resumo do conteúdo contido na página número 9
002974 Lubrication This tool requires no hourly or daily lubrication because it 1 has a grease-packed lubrication system. It should be relubri- 2 cated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances require that you should lubricate it by yourself, proceed as follows. 1. Screwdriver First, switch off and unplug the tool. 2. Plate 50 002975 Remove the plate 50 using a screwdriver, the
Resumo do conteúdo contido na página número 10
Memo 10
Resumo do conteúdo contido na página número 11
Memo 11
Resumo do conteúdo contido na página número 12
Memo 12
Resumo do conteúdo contido na página número 13
Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 13 Cut
Resumo do conteúdo contido na página número 14
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( ) From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( ) Features Power Size
Resumo do conteúdo contido na página número 15
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: 6389 boul. Couture, St. Leonard, Quebec (Montreal) H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: 1140 Rue Bégin, Ville St. Laurent, Quebec (Montreal) H4R 1X1 (514) 745 -
Resumo do conteúdo contido na página número 16
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
