Resumo do conteúdo contido na página número 1
Hammer Drill
15 mm (9/16”)
MODEL HP1500
15 mm (9/16”)
MODEL HP1501
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Resumo do conteúdo contido na página número 2
SPECIFICATIONS Model HP1500 / HP1501 Concrete 15 mm (9/16”) Capacities Steel 13 mm (1/2”) Wood 25 mm (1”) No load speed (RPM) 0 - 2,800/min. Blows per minute 0 - 44,800 Overall length 299 mm (11-3/4”) Net weight 1.7 kg (3.7 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, m
Resumo do conteúdo contido na página número 3
trician to install a polarized outlet. Do not 13. Do not overreach. Keep proper footing change the plug in any way. Double insula- and balance at all times. Proper footing and balance enables better control of the tool in tion eliminates the need for the three wire unexpected situations. grounded power cord and grounded power supply system. 14. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety 5. Avoid body contact with grounded sur- shoes, hard hat, or hearing protec
Resumo do conteúdo contido na página número 4
22. Use only accessories that are recom- tenance performed by unqualified personnel mended by the manufacturer for your could result in a risk of injury. model. Accessories that may be suitable for 24. When servicing a tool, use only identical one tool, may become hazardous when used replacement parts. Follow instructions in on another tool. the Maintenance section of this manual. Use of unauthorized parts or failure to follow SERVICE Maintenance instructions may create a risk of 23. Tool servic
Resumo do conteúdo contido na página número 5
5. Do not leave the tool running. 7. Some material contains chemicals which Operate the tool only when hand-held. may be toxic. Take caution to prevent dust inhalation and skin contact. Follow mate- 6. Do not touch the bit or the workpiece rial supplier safety data. immediately after operation; they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 5
Resumo do conteúdo contido na página número 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002455 Switch action CAUTION: Before plugging in the tool, always check to see that the 1 switch trigger actuates properly and returns to the “OFF” 2 position when released. Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Switch trigger when locking tool in “ON” position and maintain firm 2. L
Resumo do conteúdo contido na página número 7
002420 Selecting the action mode This tool has an action mode changing button. 1 For rotation with hammering, depress the button from the side with symbol fully. For rotation only, depress the button from the side with symbol fully. CAUTION: 1. Action mode changing button Always depress the action mode changing button all the way to your desired mode position. If you operate the tool with the button positioned halfway between the mode symbols, the tool may be damaged. ASSEMBLY CAUTION: Alway
Resumo do conteúdo contido na página número 8
002454 For Model HP1500 To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of 1 the three holes and tighten clockwise. Be sure to tighten all 2 three chuck holes evenly. To remove the bit, turn the chuck key counterclockwise in just one hole, then loosen the chuck by hand. 1. Chuck key After using the chuck key, be sure to return to the original 2. Chuck position. 002438 Depth gauge The depth gauge is convenient for drilling hol
Resumo do conteúdo contido na página número 9
ping away from the hole. Do not apply more pressure when the hole becomes clogged with chips or particles. Instead, run the tool at an idle, then remove the bit partially from the hole. By repeating this sev- eral times, the hole will be cleaned out and normal drilling may be resumed. 002449 Blow-out bulb (optional accessory) After drilling the hole, use the blow-out bulb to clean the dust out of the hole. 1 1. Blow-out bulb Drilling operation CAUTION: Pressing excessively on the tool will not
Resumo do conteúdo contido na página número 10
Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELI
Resumo do conteúdo contido na página número 11
Memo 11
Resumo do conteúdo contido na página número 12
Memo 12
Resumo do conteúdo contido na página número 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Resumo do conteúdo contido na página número 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Resumo do conteúdo contido na página número 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Resumo do conteúdo contido na página número 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
