Manual do usuário Makita SR1800

Resumo do conteúdo contido na página número 1

lSSmm(7X'') MODEL SRlSOO
INSTRUCTION MANUAL
Circular Saw & Standard Equipment
1
I
i
1
j
I
,
I
!
i
j
i
~
I
I
I
I
i
1' Tool body
-
2' Guide rule
DOUBLE
P Socket wrench (9)
INSULATION
Specifications
Max. cutting depth Continuous No load
Power
Blade
Overall Net
rating
diameter
speed length weight supply
45O 1 goo (In put)
cord
I
185"
45" 65" 290" 4.2kg 2.5 m

Resumo do conteúdo contido na página número 2

BEFORE CONNECTING YOUR TOOL TO A POWER SOURCE Be sure you have read all GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 2. AVOID DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Do not expose power tool in rain. 3. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area. 4. STORE IDLE TOOLS. When not in use, tools should be stored in dry,

Resumo do conteúdo contido na página número 3

PRELIMINARY INSTRUCTIONS Your electric tool is precision built and manufactured to satisfy the highest standards. For maximum performance, long tool life, and your safety, follow these instructions carefully. VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the use

Resumo do conteúdo contido na página número 4

REPLACING INSTALLING PLANER BLADES After unplugging the tool, you may remove the planer blades on the tool drum by un- screwing the three installation bolts with the socket wrench provided. The clamp plate comes off together with the blades. See Photo. 4-c Fig. 3 When you install new or sharpened blades, Hex. flange hd. bo first clean out all chips or foreign matter adhering to the drum or blades. Use blades of the same dimensions and weight, or Drum drum oscillation/vibralion will

Resumo do conteúdo contido na página número 5

FOR THE CORRECT PLANER BLADE SETTING Your planing surface will end up unsmooth and not level, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and im- proper settings. (A) Front base (Movable shoe) Although this side view cannot show it, the edges of the blades run perfect- ly parallel to the rear base surface. Cause One or both blade

Resumo do conteúdo contido na página número 6

USE OF NOZZLE ASSEMBLY Use of the special nozzle assembly (acces- sory attachment) will prevent chip scatter, making for a clean work area. Nozzle assembly \ Fig. 1( ATTACHING NOZZLE ASSEMBLY The nozzle assembly may be attached after the chip cover on the tool body is removed. When slipping on the assembly, fit the pin on it into the rear cover hole. Use the chip cover screws to fasten it in piace. Fig. 11 MAINTENANCE Caibon brushes Replace carbon brushes when they wear down to

Resumo do conteúdo contido na página número 7

185mm(7Y4")ClRCULAR SAW Model SR 1800 MODEL SRl8W 1 7

Resumo do conteúdo contido na página número 8

':iM ,":, DESCRIPTION 'L,'df A:b DESCRIPTION MACHZE 01 1 1 Switch Single Pole IWithout Lock Button1 SGE115CDY lFor USA1 Single Pole IWifh Squared Waher E Without Lwk Buttonl GPAH 4 IFor Canadd 1 C S N Bolt M6xx) 42 43 1 F Washer 6 44 1 Lever Plate Lock Plate 45 1 4b 2 C S N Bolt M6x20 47 I Plate P H Screw M4r6 IWith Washer] 48 1 49 1 1 F Washer 6 50 1 ti Nux M6 C h Screw M5x20 51 t i(.ibber S'eevr 6 52 1 5' 7 %rev. hlSXB 4aSE xS;fMB-Y IA?>embleb Items 5? & 54, Bore 4CCE