Resumo do conteúdo contido na página número 1
. :..: '
: ,..,.:f, .
. . .1
__..._ L.
.. . ...
: .; .,:. ' !
. . . ...
. .....
.. . .
.
..... ". ,
._.. .. , . .
,. .. ,
,, . .... " !.
Equipped with Keyless Chuck and Electric Brake
MODEL 6OllD
MODEL 6011DW
Wlth Fast Charger
INSTRUCTION MANUAL
SPECIFICATIONS
9 Model 8011D
Capacities
No load speed IRPMI Dimensions Net
11 x W x HJ weight
Steel Wood Wood screw Machine screw High Low
10mm 21mm 5.8mmx75mm 6mm 270 mm x 58 mm x 262 mm 1.9 kg
1318") 113/16'J 115164" x 2-5/16"
Resumo do conteúdo contido na página número 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of f
Resumo do conteúdo contido na página número 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
Resumo do conteúdo contido na página número 4
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 1200, 1210, 9000 or 9100. Other ty,pes of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or
Resumo do conteúdo contido na página número 5
. .. . . .. I. . .. ... ,r. .-. ' !_._..I . _... .. .. .. .,. . . . . . .. .. , ... .. . . , , . ::. . . .. ..,r.. :' : . .- .. ! . ..... . ... . ,. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the b
Resumo do conteúdo contido na página número 6
Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out I Set plete the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before
Resumo do conteúdo contido na página número 7
Installing or removing driver bit or dirll bit I CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. To remove the bit, hold the ring and turn the sleeve counterclockwise. Storage of driver bit When not using
Resumo do conteúdo contido na página número 8
Speed change To change the speed, turn the speed change knob 180' while the tool is running. Be Speed change knob sure that the speed change knob is turned 0 - 450 Rlmin. to the correct speed setting before you o - 1,350 Rlmin. begin operation. See arrow indication. Use the right speed for the job. Adjusting fastening torque The fastening torque can be adjusted in Adjusting ring Pointer six stages by turning the adjusting ring \ 1- so that the pointer on the adjusting ring points
Resumo do conteúdo contido na página número 9
When driving wood screws, predrill Pilot Nominal diameter Recommended size of wood screw (mm) holes to make driving easier and to pre- Of pilot hole (mm) vent splitting of the workpiece. See the 3.1 (i/8*) 2.0 - 2.2 (5/64" - 3/32") chart. 3.5 (9/64') 2.2 - 2.5 (3/32" - 3/32") 3.8 (5/32") 2.5 - 2.8 (3/32" - 7/64") 4.5 (11164") 2.9- 3.2 (7/64"- 1/8') 4.8 (3/16"1 3.1 - 3.4 (118' - 9/64") 5.1 (13/64") 3.3- 3.6 (118' - 9/63") 5.5 (7/32") 3.7 - 3.9 (9/64" - 5/32") 5.8 (15/64"1 4.0 - 4.2
Resumo do conteúdo contido na página número 10
ACC ESSO R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Fast charger 0 Bits Model DCl290 I Size I Part NO. Part No. 113119-108 Phillips Slotted 78401 1-OA Battery cartridge 1210 Part No. 632277-5 Square drill bit 784606-0A Battery c
Resumo do conteúdo contido na página número 11
Feb-04-'92 US I CORDLESS DRIVER DRILL Model 6011D 11
Resumo do conteúdo contido na página número 12
F.h-M-'S? US MODEL 8OllD ITEM NO. DESCRIPTION AtD DESCRIPTION NO. USED MA( UE 17 25 I 22 28 1 27 31 1 42 28 1 51 29 4 82 30 I 71 31 1 81 32 1 33 SI 1 34 10 1 1 35 11 1 1 36 1 12 1 13 1 37 1 38 1 14 1 15 1 39 I I8 r. 40 1 17 1 41 1 42 1 43 1 :!I 21 i I U 1 45 1 46 1 1: 1 ; 47 I 24 1 b8 1 - - Nota: Tho switch and other pan S~~CIIIC~IIO~S mry difler lrom country Io country. r MAKlTA LIMlTED ONE YEAR WARRANTY I Warranty Policy IN NO EVENT SHALL MAKITA BE LIAB
