Manual do usuário Lowrance electronic s200

Manual para o dispositivo Lowrance electronic s200

Dispositivo: Lowrance electronic s200
Categoria: Detector do radar
Fabricante: Lowrance electronic
Tamanho: 1.47 MB
Data de adição: 9/17/2014
Número de páginas: 32
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Lowrance electronic s200. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Lowrance electronic s200.

Para sua conveniência

Se a consulta dos manuais Lowrance electronic s200 diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Lowrance electronic s200 no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Lowrance electronic s200 em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Lowrance electronic s200 Manual de instruções - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Lowrance electronic s200, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Lowrance electronic s200. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

Pub. 988-0161-042

www.lowrance.com








Radar & RIM 200
Radar Interface Module
Installation Instructions

Resumo do conteúdo contido na página número 2

Copyright © 2007 Lowrance Electronics, Inc. All rights reserved. No part of this manual may be copied, reproduced, republished, trans- mitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. ® Lowrance is a registered trademark of Lowrance Electronics, Inc. ® NMEA 2000 is a registered trademark of the National Marine Elec- tronics Association. Lowrance Electron

Resumo do conteúdo contido na página número 3

Warnings and Cautions Caution: Use this radar at your own risk. This radar was designed for use as a navigation aid. It should not be used for purposes that require precise measurements of direction, distance, topography or location. Always compare the navigation information received from your radar with data from other navigation aids and sources. When a conflict arises between the navigation data from your radar and data from other navigation aids, make sure you resolve the conflict

Resumo do conteúdo contido na página número 4

switching off the radar. Before touching the magnetron or any high voltage components, ground them with a clip lead. There are no internal connections or adjust- ments necessary for installation. WARNING: Microwave Radiation Hazard The microwave energy radiated by a radar antenna is harmful to humans, especially to the eyes. NEVER look directly into an open waveguide or into the path of ra- diation from an enclosed antenna. Radar and other ra- dio frequency radiation can upset cardiac pace

Resumo do conteúdo contido na página número 5

Section 1: Introduction Thank you for purchasing this Lowrance Radar with the RIM 200 radar interface module. Your radar consists of three main components: the radar scanner unit, a display unit (sold separately) and the RIM 200 radar interface module which connects the scanner unit and the display unit. We know you’re anxious to begin the installation, but first, let us tell you how this manual is organized. The first section describes how your radar works. We'll also discuss is- sues t

Resumo do conteúdo contido na página número 6

rate targets at a distance. The critical factors are the antenna's beam width and side lobe level. Typically, a radar antenna will radiate a tightly focused beam from the front of the array. The longer the an- tenna array is, the narrower the beam width. Additionally, it will also emit smaller amounts of energy to each side. A lower side lobe level lessens the effect of a false echo. Side lobe The beam radiating the strongest radio signal from the antenna is called the "main lobe". Those

Resumo do conteúdo contido na página número 7

False echoes Sometimes radar will display targets on screen that do not exist in the real world. You should be aware of how and why this happens. A. Ghost echoes Sometimes one large object very near your boat will appear as two dif- ferent targets onscreen. One is the actual radar echo. The other is a ghost echo generated by a re-reflection of the original signal. It comes back to your own boat, bounces back to the target, and then is picked up by the antenna on the second bounce. The ac

Resumo do conteúdo contido na página número 8

Radar interference If another boat's radar is operating on the same frequency as yours, it can create interference on your display. The interference usually appears as spiral or radial patterns. This ra- dar has an interference rejection control to eliminate interference. Turn it on to reduce or eliminate the interference. Installation Considerations Prior to actual installation of the radar scanner unit, several factors must be considered to assure maximum performance. Location The sca

Resumo do conteúdo contido na página número 9

The scanner unit should be mounted on the center line of your vessel in a location that has an unobstructed view forward and is as clear as pos- sible the rest of the way around the unit. A location as high as practical to improve maximum range is desirable, keeping in mind that minimum range objects may be overlooked if mounted too high. Position the unit forward of large structures and exhaust stacks. Large structures or stacks cause blind spots. Contamination from engine ex- haust on th

Resumo do conteúdo contido na página número 10

The recommended mounting surface thickness is 3/8" to 1/2" (9 mm to 13 mm). If the mounting surface is thin, a doubler should be added. If it is thicker, longer bolts must be purchased. WARNING: The scanner will be damaged if bolts penetrate more than 9/16" (15 mm). Also, consider the cable route from the scanner to the operator’s loca- tion. Avoid routing the interconnecting cable through areas of possible damage from moving objects, machinery, exposure to chemicals or high temperature.

Resumo do conteúdo contido na página número 11

Section 2: Radar Installation Preparations Unpack your new radar and check the contents against the packing list. Do not remove the cover from the unit. There are no connections or ad- justments inside the unit needed for installation or operation. The cable must remain attached. For ease of handling, coil the cable and place it on top of the scanner, then secure it with tape. WARNING: To comply with FCC radio frequency (RF) exposure re- quirements, the radar antenna for this scanner must

Resumo do conteúdo contido na página número 12

8. Secure the cable near the scanner to support the weight of the cable and prevent strain on the watertight cable seal. If the cable is to pass through tubing or a bulkhead, protect the unfinished end. Do not use the unfinished wires or fabric braid to pull the cable. Attach a fish cord only to the cable jacket. 9. Route the cable to the RIM 200, securing it at appropriate points along the way. Make a drip loop and apply sealant at the entry point of an exterior bulkhead. Connecting Rad

Resumo do conteúdo contido na página número 13

Section 3: RIM 200 Installation The RIM 200 will replace the power cable that came with your display unit. Early RIM 200 models have four cables branching out from the cable plug. The cables include: RIM 200 radar data cable (will be con- nected to your radar), RIM 200 power cable, display unit power/data cable and NMEA 2000 network power cable. Newer RIM 200 models have three cables branching out from the cable plug. The cables include: RIM 200 radar data cable (will be connected to you

Resumo do conteúdo contido na página número 14

tail Drawing C for open array models. Wiring instructions for both ar- ray and radome antennas are listed in text format below. Connecting RIM-200 to LRA 1000, LRA 1500 and LRA 2000 Array antennas: RIM 200 Brown wire to Radar Antenna Brown wire RIM 200 Red wire to Radar Antenna Red wire RIM 200 Yellow wire to Radar Antenna Yellow wire RIM 200 Orange wire to Radar Antenna Orange wire RIM 200 Blue wire to Radar Antenna Blue wire RIM 200 Green wire to Radar Antenna Green wire Connecting RI

Resumo do conteúdo contido na página número 15

Now connect the display unit power cable green (RX) receive wire to the transmit (TX) wire from the NMEA 0183 device. There is no ground wire, so the NMEA 0183 device MUST be grounded to the same place as the display unit. NOTE: If your RIM 200 model has four branches, proceed to Step 4 to connect the RIM 200 power cable. If your RIM 200 has three branches, it does not have a RIM 200 power cable, so skip ahead to Step 5. 4. After you have wired your display unit power, connect the RIM 2

Resumo do conteúdo contido na página número 16

Connecting RIM 200 to Radome Antenna (Four-Branch Installation) * A power switch will only be con- nected to the red (+) wire. The black wire (–) will not be connected to the Display unit power switch. See Detail Drawing C (Four-Branch Installation) Cable Plug * * * * 12V RIM 200 module See Detail Drawing A LRA 1000, LRA 1500 & LRA 2000 RIM 200 Radar Power/data Radome data cable output cable antenna (RS-422) 12

Resumo do conteúdo contido na página número 17

Connecting RIM 200 to Radome Antenna (Three-Branch Installation) * A power switch will only be con- nected to the red (+) wire. The black Display unit wire (–) will not be connected to the power switch. See Detail Drawing D (Three-Branch Installation) * Cable Plug * * RIM 200 module 12V See Detail Drawing A LRA 1000, LRA 1500 & LRA 2000 Radar Power/data RIM 200 output cable Radome data cable antenna (RS-422) 13

Resumo do conteúdo contido na página número 18

Detail Drawing A Large white/pwr + ( fuse) Radar motor power { Large black/pwr – ……………… Shield/Small black ……………….. …………Data Out +/Brown/Data In + …………. ……………Data Out –/Red/Data In – ………….. …………. Data In –/Yellow/Data Out – ……...… …………. Data In +/Orange/Data Out + ………. ….. SW1 On Signal/Blue/On Signal SW1 ……. ……………. SW2+/Green/+V SW2 …………….. To radar unit To RIM 200 Detail drawing A: wiring diagram, RIM 200 to radome unit. NOTE: If you have a LRA 1000 or LRA 1500, fuse the r

Resumo do conteúdo contido na página número 19

Connecting RIM 200 to Open Array Antenna (Four-Branch Installation) * A power switch will only be con- nected to the red (+) wire. The Display unit black wire (–) will not be con- nected to the power switch. See Detail Drawing C (Four-Branch Installation) * Cable Plug * * * RIM 200 module * * 12V LRA 4000 & LRA 5000 See Detail Drawing B Open array antenna Radar power/data output cable Radar data cable (RS-422) 15

Resumo do conteúdo contido na página número 20

Connecting RIM 200 to Open Array Antenna (Three-branch Installation) * A power switch will only be con- nected to the red (+) wire. The black wire (–) will not be con- nected to the power switch. Display unit See Detail Drawing D: (Three-Branch Installation) * Cable Plug * * RIM 200 module * 12V LRA 4000 & LRA 5000 See Detail Drawing B Open array antenna Radar power/data Radar data output cable cable (RS-422) 16


Manuais similares
# Manual do usuário Categoria Baixar
1 Lowrance electronic sX-85 Manual de instruções Detector do radar 20
2 Lowrance electronic sX-75 Manual de instruções Detector do radar 19
3 Lowrance electronic LRA-1500 Manual de instruções Detector do radar 1
4 Lowrance electronic LRA-1000 Manual de instruções Detector do radar 2
5 Lowrance electronic RIM 300 Manual de instruções Detector do radar 1
6 Lowrance electronic NMEA 2000 Manual de instruções Detector do radar 1
7 Lowrance electronic LRA-2400 Manual de instruções Detector do radar 5
8 Lowrance electronic LRA-1800 Manual de instruções Detector do radar 3
9 Edelbrock 1725 Manual de instruções Detector do radar 1
10 AVE - American Video EquipmentRG-2RS Manual de instruções Detector do radar 2
11 Beltronics 995 Manual de instruções Detector do radar 108
12 Beltronics pmn Manual de instruções Detector do radar 3
13 Beltronics GX65 Manual de instruções Detector do radar 9
14 Beltronics RX65 Manual de instruções Detector do radar 158
15 Beltronics 980 Manual de instruções Detector do radar 8