Resumo do conteúdo contido na página número 1
8500 3-STACK MULTI-GYM
ASSEMBLY INSTRUCTIONS
Part # 6866301 1 Revision:3/15/00
Resumo do conteúdo contido na página número 2
IMPORTANT NOTES Please note: * Thank you for purchasing the LIFE FITNESS 8500 MULTI-GYM. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your LIFE FITNESS customer service represen- tative at (800) 328-9714. There is a risk assumed by individuals
Resumo do conteúdo contido na página número 3
PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 6617103 REAR UPRIGHT 1 59 3118401 4” VINYL CAP 1 2 6779802 LEG BACK PAD ADJUST 1 60 6140701 1 X 1” GLIDE 5 3 6625502 LEG BACK PAD SUPPORT 1 61 6177001 2-1/2 X 5-1/2 NON-SKID STRIP 4 4 6624202 BACK PAD ANGLE LEFT 1 62 6412001 3/8 X 2-3/4” DIA. SPRING PIN 6 5 6624302 BACK PAD ANGLE RIGHT 1 63 6466901 1/2 X 3-1/2” DIA. SPRING PIN 1 6 6622903 PEC ARM RIGHT 1 64 6427101 KEYHOLE CLEVIS 1 7 6623003 PEC ARM LEFT 6692601 3 X 2” END CAP 2
Resumo do conteúdo contido na página número 4
23 1/2 X 3-1/4” 95 25 24 61 85 FIGURE 1 STEP 1: • LOOSELY assemble the LEG WEIGHT STACK BASE (23) and the PRESS WEIGHT STACK BASE (24) to the BASE (25) using two 1/2 X 3-1/4” BOLTS (95) and two 1/2” LOCK NUTS (85) as shown in FIGURE 1. • Apply two NON-SKID STRIPS (61) to the BASE (25) as shown in FIGURE 1. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 3 4 5 6 4
Resumo do conteúdo contido na página número 5
96 1/2 X 4”” 84 30 85 85 95 1/2 X 3-1/4” 1 29 85 84 94 1/2 X 3” 25 85 95 1/2 X 3-1/4” FIGURE 2 STEP 2: • LOOSELY assemble the FRONT UPRIGHT (29) to the BASE (25) using two 1/2 X 3-1/4” BOLTS (95) and two 1/2” LOCK NUTS (85) as shown in FIGURE 2. • LOOSELY assemble the REAR UPRIGHT (1) to the BASE (25) using one 1/2 X 3” BOLT (94), two 1/2” WASHERS (84), and one 1/2” LOCK NUT (85) as shown in FIGURE 2. • LOOSELY assemble the TOP BOOM (30) to the REAR UPRIGHT (1) using two 1/2 X 4” BOLTS (
Resumo do conteúdo contido na página número 6
105 29 92 3/8 X 4” 80 104 13 1/2” LOW 80 HEIGHT 86 11 3/8 X 1-1/4” 88 1/2 X 4” 96 12 62 FIGURE 3 STEP 3: • SECURELY assemble the FLOATING PULLEY STOP (11) and the SEAT SUPPORT (12) to the FRONT UPRIGHT (29) using two 1/2 X 4” BOLTS (96) and two 1/2” LOW HEIGHT LOCK NUTS (86) as shown in FIGURE 3. • SECURELY assemble one 3/8 X 2-3/4” SPRING PIN (62) to the SEAT SUPPORT (12) as shown in FIGURE 3. • SECURELY assemble one PEC SEAT PAD (104) to the PAD SUPPORT (13) using two 3/8 X 1-1/4” BOLTS
Resumo do conteúdo contido na página número 7
60 1/2 X 4” 96 10 29 27 86 1/2” LOW HEIGHT 79 41 72 40 28 71 7 71 6 84 85 62 99 80 3/8 X 3-1/4” 91 FIGURE 4 STEP 4: • SECURELY assemble the BEARING HOUSING (10) and the CENTER PULLEY BRACKET (27) to the FRONT UPRIGHT (29) using two 1/2 X 4” BOLTS (96) and two 1/2” LOW HEIGHT LOCK NUTS (86). • Assemble the RIGHT PEC ARM (6) and one PEC CAM (28) to the BEARING HOUSING (10) using one 3/4” SLEEVE BEARING (72), two 3/4” FLANGE BEARINGS (71), one 1/2” WASHER (84), and one 1/2” LOCK NUT (85) as
Resumo do conteúdo contido na página número 8
73 14 37 59 62 52 FIGURE 5 STEP 5: • SECURELY assemble one 3/8 X 2-3/4” SPRING PIN (62) to the WOLFF SLEEVE (14) as shown in FIGURE 5. • Assemble one U-PIN (52) to the WOLFF SLEEVE (14) using one 1/2” PAL NUT (73). • Slide one 4” VINYL SLEEVE (59) onto the U-PIN (52) as shown in FIGURE 5. • CAREFULLY slide the WOLFF SLEEVE (14) onto the PRESS FRAME (37) until the SPRING PIN engages in one of the holes. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 3 4 5 6 8
Resumo do conteúdo contido na página número 9
94 1/2 X 3” 38 1 84 85 86 1/2” LOW HEIGHT 35 94 1/2 X 3” 84 85 25 FIGURE 6 STEP 6: • SECURELY assemble the PRESS BASE (38) to the BASE (25) using two 1/2 X 3” BOLTS (94), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85), and to the REAR UPRIGHT (1) using one 1/2 X 3” BOLT (94), one 1/2” WASHER (84), and one 1/2” LOCK NUT (85) as shown in FIGURE 6. • Assemble the SWIVEL PULLEY BRACKET (35) to the PRESS BASE (38) using one 1/2” LOW HEIGHT LOCK NUT (86) as shown in FIGURE 6. (NOTE: Securely
Resumo do conteúdo contido na página número 10
94 1/2 X 3” 84 115 3/8 X 3” COUNTER SUNK 37 57 84 85 38 80 82 FIGURE 7 STEP 7: • SECURELY assemble the PRESS FRAME (37) to the PRESS BASE (38) using one 1/2” X 3” BOLT (94), two 3/8 X 3” COUNTERSUNK BOLTS (115), one 4-1/2” X 8” PLATE (57), two 1/2” WASHERS (84), two 3/8” WASHERS (80), one 1/2” LOCK NUT (85), and two 3/8” LOCK NUTS (82). (NOTE: Make sure 3/8” countersunk bolts are facing down.) See FIGURE 7. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 3 4 5 6 10
Resumo do conteúdo contido na página número 11
101 80 3/8 X 1-1/4” 88 5 1/2” LOW 86 HEIGHT 84 54 1/2 X 1-1/4” 93 37 116 85 100 4 38 14 76 80 3/8 X 1-1/4” 88 97 1/2 X 6-1/2” FIGURE 8 STEP 8: • Slide two HINGE TABS (76) onto the WOLFF SLEEVE (14) and SECURELY attach PRESS SEAT PAD (100) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). (NOTE: The “hinge” part of the HINGE TAB (76) should face upward as shown in FIGURE 8.) • Slide the RIGHT BACK PAD ANGLE (5) and LEFT BACK PAD ANGLE (4) onto the WOLFF SLEEVE (14) and attach the
Resumo do conteúdo contido na página número 12
1 82 36 49 80 91 3/8 X 3-1/4” 85 84 38 9 96 1/2 X 4” 61 FIGURE 9 STEP 9: • LOOSELY assemble the PRESS ARM ADJUST (36) to the REAR UPRIGHT (1) using two 1” PILLOW BLOCK BEARINGS (49), four 3/8 X 3-1/4” BOLTS (91), four 3/8” WASHERS (80), and four 3/8” LOCK NUTS (82). (NOTE: Assemble PILLOW BLOCKS (49) so the set screws are on the outside, this will allow more adjustment.) See FIGURE 9. • Center PRESS ARM ADJUST (36) to line up with the post on the PRESS BASE (38) and securely tighten set sc
Resumo do conteúdo contido na página número 13
36 82 86 1/2” LOW HEIGHT 70 84 8 90 3/8 X 2-3/4” 63 98 1/2 X 7-1/2” FIGURE 10 STEP 10: • SECURELY assemble one 1/2 X 3-1/2” SPRING PIN (63) to the PRESS ARM (8) as shown in FIGURE 10. • SECURELY assemble the PRESS ARM (8) to the PRESS ARM ADJUST (36) using one 1/2 X 7-1/2” BOLT (98), two 1/2” WASHERS (84), two 1/2” FLANGE BEARINGS (70), and one 1/2” LOW HEIGHT LOCK NUT (86). (NOTE: SECURELY tighten, then back nut off 1/4 to allow the PRESS ARM to rotate freely.) • SECURELY assemble f
Resumo do conteúdo contido na página número 14
34 85 86 31 94 1/2 X 3” FIGURE 11 STEP 11: • SECURELY assemble the REAR BASE LEG (31) to the LEG FRAME (34) using two 1/2 X 3” BOLTS (94), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85) as shown in FIGURE 11. 82 80 76 16 15 34 76 95 3/8 X 3-1/4” FIGURE 12 STEP 12: • SECURELY assemble the LEFT & RIGHT LEG EXTENSION HANDLES (16 & 15) to the LEG FRAME (34) using two 3/8 X 3-1/4” BOLTS (91), four 3/8” WASHERS (80), and two 3/8” LOCK NUTS (82). See FIGURE 12. • Slide two HINGE TABS (76) on
Resumo do conteúdo contido na página número 15
88 3/8 X 1-1/4” STEP 13: • SECURELY assemble one 2 X 8” PLATE (17) to the LEG SEAT 80 PAD (102) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” 54 WASHERS (80). See FIGURE 13. 17 • Apply one 1-1/4” RUBBER BUMPER (54) to the 2 X 8” PLATE (17) as shown in FIGURE 13. 102 FIGURE 13 102 66 76 80 88 3/8 X 1-1/4” 34 FIGURE 14 STEP 14: • SECURELY assemble the LEG SEAT PAD (102) to the HINGE TABS (76) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 14. • SECURELY assemble o
Resumo do conteúdo contido na página número 16
3 1/2 X 6-1/2” 97 2 2 60 70 3/8” BLACK 81 LOCKWASHER 85 3/8 X 1” BUTTON HEAD 87 32 71 77 54 NOTE: TIGHTEN BOTH AT THE SAME TIME! 34 FIGURE 15 STEP 15: • SECURELY assemble one 1 X 1” GLIDE (60) to the angle on the BACK PAD ADJUST (2) as shown in FIGURE 15. • Assemble LEG BACK PAD ADJUST (2) and LEG BACK PAD SUPPORT (3) to the LEG FRAME (34) using one 1/2 X 6-1/2” BOLT (97), two 1/2” FLANGE BEARINGS (70), one 1/2” LOCK NUT (85) as shown in FIGURE 15. (NOTE: Securely tighten, then back
Resumo do conteúdo contido na página número 17
3/8 X 3-1/4” 91 80 3 79 41 103 39 2 34 FIGURE 16 STEP 16: • SECURELY assemble the LEG BACK PAD (103) to the LEG BACK PAD ADJUST (2) and the LEG BACK PAD SUPPORT (3) using four 3/8 X 3-1/4” BOLTS (91) and four 3/8” WASHERS (80). See FIGURE 16. • SECURELY assemble two 4 X 7” ROLLER PADS (41) to the LEG FRAME (34) using one 19-1/4” TUBE (39) and two 1-5/16” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. 17
Resumo do conteúdo contido na página número 18
32 82 84 85 87 3/8 X 1-1/4” 33 BUTTON HEAD 23 65 62 41 34 1/2 X 4” 96 79 FIGURE 17 STEP 17: • SECURELY assemble two 3/8 X 2-3/4” SPRING PINS (62) to the PAD SLEEVES (33) as shown in FIGURE 17. • Assemble four ROLLER PADS (41) to the PAD SLEEVES (33) using four 1-5/16” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. • Slide PAD SLEEVES (33) over LEG CURL/EXTENSION (32) until the spring pin pops into the holes. (NOTE: PAD SLEEVES should be facing as
Resumo do conteúdo contido na página número 19
78 19 53 3/8” LOCK WASHER 81 3/8 X 1-1/4” 88 50 TWO PER SIDE ON THIS STACK ONLY! TWO 106 PER SIDE! 23 108 107 24 25 47 FIGURE 19 STEP 19: • Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS (19) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19. • Using EXTREME CARE slide twenty WEIGHT PLATES (106) down over the GUIDE RODS (19) with
Resumo do conteúdo contido na página número 20
85 21 20 30 19 95 1/2 X 3-1/4” FIGURE 20 STEP 20: • Slide the PRESS GUIDE ROD SUPPORT (20) and LEG GUIDE ROD SUPPORT (21) over their respective GUIDE RODS (19) and SECURELY assemble them to the TOP BOOM (30) using two 1/2 X 3-1/4” BOLTS (91) and two 1/2” LOCK NUTS (85) as shown in FIGURE 20. 21 20 80 3/8 X 2-3/4” 90 83 3/8” LOW HEIGHT 22 78 30 19 FIGURE 21 STEP 21: • Slide the PEC GUIDE ROD SUPPORT (22) onto the GUIDE RODS (19) and SECURELY assemble the PEC GUIDE ROD SUPPORT (22) to TOP BOOM
