Manual do usuário Life Fitness C9

Resumo do conteúdo contido na página número 1

Lifecycle Exercise Bike
ASSEMBLY INSTRUCTION S
TM

Resumo do conteúdo contido na página número 2

Congratulations... and welcome to the world of Life Fitness and the Lifecycle C7i / C9i exercise bike. The following Parts Identification Listing and the step-by-step installation procedures have been assembled to make the set-up of your exercise bike as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Lifecycle exercise bike…

Resumo do conteúdo contido na página número 3

IMPORTANT SAFETY INSTRUCTIONS ! ⇒ DO NOT locate the Lifecycle exercise bike outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Lifecycle exercise bike if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number on the back page of this Installation Instruction Guide. ⇒ DO NOT locate the Lifecycle exercise bike any closer than 30 inches ( 76 cm ) to a television set. ⇒ DO NOT locate ad

Resumo do conteúdo contido na página número 4

TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, 1/2” wrench PARTS DESCRIPTION STABILIZER/HANDLEBAR BOLT Qty:5 2 CONSOLE SCREW Qty: 4 1 0017-00101-0933 0017-00101-1253 SEAT WITH SEATPOST ASSEMBLY Qty: 1 4 COLLAR Qty: 1 3 AK17-00120-0003 0K18-01156-0001 HANDLEBAR ASSEMBLY Qty: 1 6 DISPLAY CONSOLE ASSEMBLY Qty: 1 5 AK18-00215-0000 (Model C7i) AK52-00004-0000 (Model C9i) STABILIZER BAR Qty: 1 8 9V ALKALINE BATTERY Qty: 1 7 AK18-00070-0000 0017-00003-0757 1 2 1” 2” 3” 4” 5”

Resumo do conteúdo contido na página número 5

6 8 CAUTION: Improper insertion of the seat pin may result in serious injury. Always 5 make sure the pin is properly engaged in 2 the seat post hole prior to using the Lifecycle exercise bike 1 4 3 1 7

Resumo do conteúdo contido na página número 6

C 1. Before proceeding, familiarize yourself with the parts of the Lifecycle exercise bike and make sure that you have received all the items described in the Parts List. 2. Remove the STABILIZER BAR (#7) from the carton base. Use the empty CONSOLE CARTON to raise the rear of the LIFECYCLE exercise bike as shown. Remove the two BOLTS (#1) from the bottom of the SHIPPING STABILIZER, save the BOLTS and store the SHIPPING STABILIZER with the other shipping containers. 3. Use the same two BOLTS that

Resumo do conteúdo contido na página número 7

6 8. There is a large hole in the rear of the display console (#6) through which you can see a 10-pin connector and a 4-pin connector. These correspond to the matching connectors on the wire harness protruding from the top of the handlebar. Model C7i Only: Properly align the locking tabs of the 16-PIN CONNECTOR (16P) on the WIRE HARNESS with the 16-PIN CONNECTOR on the back of the DISPLAY CONSOLE, then snap them together. Next, align the locking tabs of the 3-PIN CONNECTOR (3P) on the WIRE HARNE

Resumo do conteúdo contido na página número 8

PRE-OPERATION CHECKLIST 4 Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight. 4 Make sure the exercise bike is properly leveled and stable. 4 Confirm the display console is set to English or metric units. (See Optional Settings ENG/MET in Operation Manual.) 4 Read the entire Operation Manual before using the exercise bike. Before attempting to operate your Lifecycle recumbent exercise bike, it is imperative that you familiarize yourself with the contents of the Operation M