Manual do usuário Keys Fitness Strength trainer ST-1000

Resumo do conteúdo contido na página número 1

M M A A N N U U A A L L
O O W W N N E E R R ’’ S S M M A A N N U U A A L L
O O W W N N E E R R ’’ S S
ST-1000
HOME GYM
Questions?
Call our toll free Keys Fitness Helpline
1-800-683-1236

Resumo do conteúdo contido na página número 2

THANK YOU for making this Strength Trainer unit a part of your exercise program. Keys Fitness and our Strength Trainer Series assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please con- tact us at our Keys Fitness Helpline. We have trained service technicians on site to take care of you, our valued customer. REGISTRATION CARD To

Resumo do conteúdo contido na página número 3

BEFORE YOU START Prior to assembly, remove components from the box and verify that all the listed parts were supplied. SAFETY INFORMATION WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. Keys Fitness Products LP assumes no responsibil- ity for personal injury or property damage sustained by or through the use of this product. It is the owner’s

Resumo do conteúdo contido na página número 4

PARTS

Resumo do conteúdo contido na página número 5

PARTS

Resumo do conteúdo contido na página número 6

PARTS

Resumo do conteúdo contido na página número 7

PARTS

Resumo do conteúdo contido na página número 8

PARTS LIST # DESCRIPTION QTY # DESCRIPTION QTY # DESCRIPTION QTY 1 Base Frame 1 46 Bushing 20 90 Bolt M10*115 1 2 Foot Plate 1 47 Double Pulley Bracket 4 91 Bolt M10*95 2 3 Main Upright 1 48 Lat Pull Bar 1 92 Bolt M10*85 3 4 Rear Cross Beam 1 49 Low Pull Bar 1 93 Bolt M10*80 1 5 Rear Top Beam 1 50 Weight Plate Assembly 1 94 Bolt M10*75 16 6 Main Top Beam 1 51 Selector Rod 1 95 Bolt M10*70 12 7 Foot Plate Bracket 1 52 Selector Pin 1 96 Bolt M10*65 2 8 Lat Pull Down Bar 1 53 Chain 1 97 Bolt M10*50

Resumo do conteúdo contido na página número 9

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Do not use bolt here yet. Wait for STEP 6. Do not use bolt here yet. Wait for STEP 6.

Resumo do conteúdo contido na página número 10

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

Resumo do conteúdo contido na página número 11

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

Resumo do conteúdo contido na página número 12

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Feed Cable (63) through framework as pictured. Hold cable in place by placing in pulley grooves and bolting pulleys to frame.

Resumo do conteúdo contido na página número 13

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. First, insert guide rods into rear cross beam (4). Then slide on, from top to bot- tom, rubber bushings (125), 19 weight plates (128) and weight plate assembly (50). Secure in place as pictured. 11

Resumo do conteúdo contido na página número 14

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. 12

Resumo do conteúdo contido na página número 15

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. 13

Resumo do conteúdo contido na página número 16

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. 14

Resumo do conteúdo contido na página número 17

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Hex Screws (109) are already pre-assembled for you. Make sure to unscrew them before sliding in shafts (43). 15

Resumo do conteúdo contido na página número 18

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Note: Hex screws (109) are already pre-assembled for you. Make sure to uncrew them before sliding in shaft(39). 16

Resumo do conteúdo contido na página número 19

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Note: Hex screws are already pre-assembled for you. Make sure to unscrew them before sliding in shaft (39). 17

Resumo do conteúdo contido na página número 20

ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. 18