Manual do usuário Jet Tools JDP-17MF

Manual para o dispositivo Jet Tools JDP-17MF

Dispositivo: Jet Tools JDP-17MF
Categoria: Furadeira
Fabricante: Jet Tools
Tamanho: 1.62 MB
Data de adição: 9/5/2013
Número de páginas: 24
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Jet Tools JDP-17MF. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Jet Tools JDP-17MF.

Para sua conveniência

Se a consulta dos manuais Jet Tools JDP-17MF diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Jet Tools JDP-17MF no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Jet Tools JDP-17MF em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Jet Tools JDP-17MF Manual de instruções - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Jet Tools JDP-17MF, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Jet Tools JDP-17MF. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

This Manual is Bookmarked




Operating Instructions and Parts Manual
17” Drill Press
Model JDP-17MF



WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-354169
Ph.: 800-274-6848 Revision C1 01/06
www.wmhtoolgroup.com Copyright © WMH Tool Group

Resumo do conteúdo contido na página número 2

This manual has been prepared for the owner and operators of a JDP-17MF Drill Press. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your JET Drill Press, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully.

Resumo do conteúdo contido na página número 3

, WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. Support workpiece adequately at all times during operation; maintain control of work at all times. This drill press is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a drill press, do not use until proper training and knowledge has b

Resumo do conteúdo contido na página número 4

• USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. • NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. • CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, b

Resumo do conteúdo contido na página número 5

Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local

Resumo do conteúdo contido na página número 6

230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This JET drill press is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug (A), supplied with the drill press, must be replaced with a UL/CSA listed plug suitable for 230V operation (D)

Resumo do conteúdo contido na página número 7

On-Off Switch Padlock Model No. BP-1, Stock No. 709736 To safeguard your machine from unauthorized operation and to avoid accidental starting by young children, the use of a padlock is highly recommended. JET model BP-1 is available from your local authorized JET distributor or by calling WMH Tool Group at 800-274-6848. To lock out an on-off switch: 1. Open the padlock. See Fig. A. 2. Insert through holes in the start button. See Fig. B 3. Close the padl

Resumo do conteúdo contido na página número 8

Specifications: JDP-17MF Stock Number ..................................................................................................................................... 354169 Swing....................................................................................................................................................16-1/2” Type ......................................................................................................................................................

Resumo do conteúdo contido na página número 9

Contents of the Shipping Container 1. Head Assembly 1. Table 1. Column and Bracket Assembly 1. Base 1. Owner’s Manual 1. Warranty Registration Card 1. Chuck and Chuck Key 3. Downfeed Handle 1. Table Bracket Lock Handle 1. Table Bracket Raising Handle 4. M10 x 40 Hex Cap Bolts 1. Arbor 1. Drift Key Tools Supplied for Assembly 1. 3mm Hex Wrench 1. 5mm Hex Wrench Tools Required for Assembly 1. 17mm Box Wrench or a 6”-8” Adjustable Wrench , WARNING! Read a

Resumo do conteúdo contido na página número 10

Assembly 1. Place the base (A, Fig. 1) on a level floor. 2. With a 17mm wrench attach the column assembly (B, Fig. 1) to the base (A, Fig. 1) with four M10 x 40 hex cap bolts (C, Fig. 1). Tighten firmly. 3. Thread lock handle (D, Fig. 2) into the table bracket (E, Fig. 2). 4. Loosen the set screw (F, Fig. 3) on the raising handle (G, Fig. 3) with a 3mm hex wrench. 5. Slide the handle onto the table bracket shaft. 6. Turn the handle until the set screw is opposite

Resumo do conteúdo contido na página número 11

9. With the aid of a second person, carefully lift below the chuck. the head onto the column top. Caution: The head assembly is heavy! Use care 3. Place a piece of scrap wood on the table, and lower quill using the down feed handle. when lifting onto the column! 4. Rotate spindle to align the key hole in the 10. Rotate head assembly until sides of the belt spindle with the key hole in the quill. cover are parallel with the sides of the base. 5. Insert the drift key (D, Fig.

Resumo do conteúdo contido na página número 12

Adjusting the Depth Stop To drill multiple holes at the same preset depth, use the depth stop: 1. Use a pencil to mark the depth the bit will drill into the workpiece (A, Fig. 7). 2. With the drill bit in the chuck, lower down feed handle to advance bit to your mark,see Figure 7. 3. With your other hand, advance the lock nuts (B, Fig. 7) on the depth stop rod until they are snug to the seat (C, Fig. 7). 4. The drill bit will now advance to this point. 5. To release, advan

Resumo do conteúdo contido na página número 13

Speed & Pulley Chart 13

Resumo do conteúdo contido na página número 14

Return Spring Adjustment The return spring is adjusted at the factory and should not need further adjustment. If adjustment is deemed necessary: 1. Unplug the machine from the power source. 2. Loosen two jam nuts (A, Fig. 9). Do not remove. 3. Firmly hold the coil spring cover (B, Fig. 9). 4. Pull out the cover and rotate until the pin (C, Fig. 9) on the return spring plate engages the next notch in the coil spring cover. Turn the cover clockwise to decrease tension an

Resumo do conteúdo contido na página número 15

Basic Operation • Always use a back-up piece of scrap wood to cover the table. This protects both the table and the drill bit. • Place material to be drilled in such as way as to come into contact with the left side of the column. This prevents the material from spinning. , WARNING! If the work piece is not large enough to come into contact with the column, use a clamp or drill press vise that is securely fastened to the table! Failure to comply may cause serious injury!

Resumo do conteúdo contido na página número 16

Troubleshooting Trouble Probable Cause Remedy 1. Drill press unplugged from 1. Check all plug connections. wall, or motor. 2. Replace fuse, or reset circuit 2. Fuse blown, or circuit breaker breaker. Drill press will not start. tripped. 3. Replace cord. 3. Cord damaged. 4. Replace starting capacitor. 4. Starting capacitor bad. 1. Extension cord too light or too 1. Replace with adequate size Drill press does not come long. and length cord. up to speed. 2. Low current. 2. Conta

Resumo do conteúdo contido na página número 17

Parts Breakdown for JDP-17MF 17

Resumo do conteúdo contido na página número 18

Parts List for JET JDP-17MF Drill Press Index Part No. No. Description Size Qty. 1 ..........10600111 ......................Base..................................................................... .................................... 1 2A........12909001A1..................Column and Holder Assy. .................................... .................................... 1 3 ..........TS-1525021 ..................Set Screw............................................................. M10x

Resumo do conteúdo contido na página número 19

Index Part No. No. Description Size Qty. 61 ........BB-6203Z ......................Ball Bearing.......................................................... .................................... 1 62 ........10606201 ......................Washer................................................................. .................................... 1 63 ........10606301 ......................Lock Nut............................................................... ..................................

Resumo do conteúdo contido na página número 20

Index Part No. No. Description Size Qty. 169 ......11316904 ......................Nameplate............................................................ .................................... 1 601 ......TS-1533032 ..................Pan Head Machine Screw ................................... M5x10 ......................... 2 602 ......2504MZC005 ................Tooth Washer ...................................................... .................................... 2 607 ......TS-0720101 .....


Manuais similares
# Manual do usuário Categoria Baixar
1 Jet Tools 720HD Manual de instruções Furadeira 1
2 Jet Tools JDP-17FSE Manual de instruções Furadeira 0
3 Jet Tools JDP-15M/MF Manual de instruções Furadeira 16
4 Jet Tools JFM-5 Manual de instruções Furadeira 2
5 Jet Tools JDP-20VS Manual de instruções Furadeira 3
6 Jet Tools JDP-17DX Manual de instruções Furadeira 4
7 Jet Tools Bench JDP-12 Manual de instruções Furadeira 0
8 Jet Tools PM2800 Manual de instruções Furadeira 4
9 Jet Tools M-1791309 Manual de instruções Furadeira 0
10 Jet Tools 719T WMH Manual de instruções Furadeira 1
11 AllTrade COMPONENT #690551-1HR Manual de instruções Furadeira 0
12 Ardisam Earthquake 8902 Manual de instruções Furadeira 2
13 Ardisam Earthquake 8900 Manual de instruções Furadeira 1
14 Ardisam Earthquake 9000 Manual de instruções Furadeira 18
15 Ardisam Earthquake 9200 Manual de instruções Furadeira 0