Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY WEIGHT BENCH
Hardware Pack
PRO 6
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PRO 6
Retain This
Manual for
Reference
07-26-03
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE.....................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 5 EXPLODED DIAGRAM……….......................................
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
Resumo do conteúdo contido na página número 4
HARDWARE PACK 3
Resumo do conteúdo contido na página número 5
HARDWARE PACK 4
Resumo do conteúdo contido na página número 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach an Upright Beam (#4) to the Left Stabilizer (#1). Then attach the Cross Brace (#3) to the Upright Beam. Align the holes and secure them with two M10 x 3” Carriage Bolts (#45), two ∅ ¾” Washers (#58), and two M10 Aircraft Nuts (#56). Repeat t
Resumo do conteúdo contido na página número 7
STEP 2 (See Diagram 2) A.) Slide the Sliding Block (#17) onto the Main Seat Support (#6). Use a M18 Lock Knob (#24) to hold the Sliding Block in position. B.) Attach the Rear of the Main Seat Support to the Cross Brace (#3). Secure them with two M10 x 2 ½” Carriage Bolts (#47), ∅ ¾” Washers (#58), and M10 Aircraft Nuts (#56). C.) Attach the Front Stabilizer (#5) to the front of the Main Seat Support. Secure them with one M10 x 2 ½” Carriage Bolt (#47) from the top, two M10 x 2 ¾” Carr
Resumo do conteúdo contido na página número 8
STEP 3 (See Diagram 3) A.) Attach the Seat Bracket (#12) to the short pivot on the Sliding Block (#17). Secure it with one M10 x 5” Allen Bolt (#48), two ∅ ¾” Washers (#58), and one M10 Aircraft Nut (#56). B.) Place the Backrest Incline Support (#10) in between the two Backrest Supports (#9). Attach the Backrest Supports to the long Pivot on the Sliding Block. C.) Place the Backrest Board (#20) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Hex Bolts (#53) and ∅ ½” Wash
Resumo do conteúdo contido na página número 9
STEP 4 (See Diagram 4) A.) Insert one Foam Roll Tube (#8) halfway through the hole on the Leg Developer Holder (#7). Insert two Foam Roll Tubes (#8) halfway through the holes on the Leg Developer (#23). Push six Foam Rolls (#30) onto the Tubes from both ends. Plug six Foam Roll End Caps (#31) into the ends. B.) Attach the Arm Curl Pad (#21) to the Arm Curl Stand (#18). Secure it with two M8 x 5/8” Allen Bolts (#51) and Ø 5/8” Washers (#59). Insert the Arm Curl Stand into the open s
Resumo do conteúdo contido na página número 10
9
Resumo do conteúdo contido na página número 11
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Stabilizer 1 51 M8 x 5/8” Allen Bolt 2 2 Right Stabilizer 1 52 M12 x 3 3/8” Hex Bolt 1 3 Cross Brace 1 53 M6 x 1 3/8” Hex Bolt 4 4 Upright Beam 2 54 M6 x 5/8” Hex Bolt 4 5 Front Stabilizer 1 55 M12 Aircraft Nut 1 6 Main Seat Support 1 56 M10 Aircraft Nut 11 7 Leg Developer Holder 1 57 Ø 1” Washer 2 8 Foam Tube 3 58 Ø ¾” Washer 15 9 Backrest Support 2 59 Ø 5/8” Washer 2 10 Backrest Incline Support 1 60 Ø ½” Washer
Resumo do conteúdo contido na página número 12
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu
