Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE ELITE
Hardware Identifier
Assembly Instruction PHE 2000
Parts List
Warranty
Ordering Parts
Model
PHE 2000
Retain This
Manual for
Reference
05-31-04
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-f
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 6 WEIGHT RESISTANCE CHART....................................................
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Resumo do conteúdo contido na página número 4
HARDWARE PACK 3
Resumo do conteúdo contido na página número 5
HARDWARE PACK 4
Resumo do conteúdo contido na página número 6
HARDWARE PACK 5
Resumo do conteúdo contido na página número 7
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Middle Base Frame (#1) between the Front & Rear Base Frames (#2 & #3). Align the holes. Secure them with two M10 x 2 ¾” Carriage Bolts (#72), two ∅ ¾” Washers (#87), and two M10 Aircraft Nuts (#89). B.) Attach the Foot Plate (#15) to the
Resumo do conteúdo contido na página número 8
STEP 2 (See Diagram 2) A.) Place two ∅ 2 ½” Rubber Bumpers (#65) on the Rear Base Frame (#2). Align the holes and insert Two Guide Rods (#18) through the holes into the Rear Base Frame. Secure each Guide Rod with one M10 x 1” Allen Bolt (#75) and ∅ ¾” Washer (#87) from the bottom of Rear Base Frame. B.) Slide 14 Weight Plates (#48) onto the Guide Rods. Make sure all Plates are facing the same direction. Insert the Selector Rod (#41) through the center hole on the Weight Plates. Slide
Resumo do conteúdo contido na página número 9
STEP 3 (See Diagram 3) A.) Attach the Upper Frame (#4) onto the two Guide Rods (#18). Secure each Guide Rod to the Upper Frame with on M10 x 1” Allen Bolt (#75) and ∅ ¾” Washer (#87). DO NOT tighten the Nuts and Bolts yet. B.) Place the Upper Frame (#4) onto the top of the Vertical Frame (#5). Secure it with one 5 ½” x 2” Bracket (#27), two M10 x 2 ¾” Carriage Bolts (#72), two ∅ ¾” Washers (#87), and two M10 Aircraft Nuts (#89). C.) Securely tighten all Nuts and Bolts previously
Resumo do conteúdo contido na página número 10
DIAGRAM 3 9
Resumo do conteúdo contido na página número 11
STEP 4 (See Diagram 4) A.) Attach two Diagonal Support Frames (#7) to the Front Base Frame (#3). Secure it with one M10 x 3” Carriage Bolt (#77), ∅ ¾” Washer (#87), and M10 Aircraft Nut (#89). B.) Secure the two Diagonal Supports to the Seat Support Frame (#6) with one M10 x 3” Carriage Bolt (#77), ∅¾” Washer (#87), and M10 Aircraft Nut (#89). C.) Attach the Leg Developer (#8) to the top of the Diagonal Support Frames (#7). Secure it with one M10 x 3” Allen Bolt (#74), two ∅ ¾” Washe
Resumo do conteúdo contido na página número 12
STEP 5 (See Diagram 5) A.) Attach the Front Press (#11) to the pivot on the Front Press Base (#10). Align the holes and insert the Front Press Axle (#32) through the holes. B.) Secure each end of the Axle with one M10 x ¾” Allen Bolt (#76) and ∅1 3/8” Washer (#66). Secure the Axle to the Front Press with two M8 x ¾” Screws (#88). C.) Thread a Short T-shape Lock Pin (#52) into the hole on the Front Press. Use the Lock Pin to secure the desired Front Press exercise position. D.) Attac
Resumo do conteúdo contido na página número 13
STEP 6 (See Diagram 6) A.) Attach the Butterfly Base (#14) to the Vertical Frame (#5). Secure it with one 4 ¾” x 2” Bracket (#26), two M10 x 3 ½” Carriage Bolts (#71), two ∅ ¾” Washers (#87), and two M10 Aircraft Nuts (#89). B.) Insert the Right Butterfly (#20) into the right pivot on Butterfly Base. Secure it with one M10 x ¾” Allen Bolt (#76) and ∅1 3/8” Washer (#66) from the bottom. C.) Insert the Butterfly Handle (#13) into the pivot on the Right Butterfly. Secure it with one M1
Resumo do conteúdo contido na página número 14
STEP 7 (See Diagram 7) A.) Place the Seat Pad (#21) onto the Seat Post (#9). Secure it with two M8 x 1 5/8” Allen Bolts (#82) and ∅ 5/8” Washers (#86). B.) Insert the Seat Post into the opening on the Seat Support Frame (#6). Use a Lock Knob (#44) to obtain the desired height of Seat. C.) Insert two Foam Tubes (#28) halfway through the holes on Seat Post and Leg Developer. Push four Foam Rolls (#64) onto the Tubes from both ends. Plug four Foam Roll End Caps (#58) onto the Tubes. DIA
Resumo do conteúdo contido na página número 15
CABLE LOOP DIAGRAM 14
Resumo do conteúdo contido na página número 16
STEP 8 (See Diagram 8 & Upper Cable Loop Diagram) A.) Attach the 154” Upper Cable (#34) to the opening on the front Upper Frame (#4). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#45) to the Cable. Secure the Pulley with one M10 x 2 ½” Allen Bolt (#78), two ∅ 5/8” x 5/8” Pulley Bushings (#60), and one M10 Aircraft Nut (#89). B.) Draw the Cable over the Pulley along the Upper Frame towards the back of the machine to the opening in the middle of Upper Frame. R
Resumo do conteúdo contido na página número 17
DIAGRAM 8 16
Resumo do conteúdo contido na página número 18
Upper Cable Loop Diagram 17
Resumo do conteúdo contido na página número 19
STEP 9 (See Diagram 9 & Lower Cable Loop Diagram) A.) Attach the 156” Lower Cable (#36) to the opening on the Leg Developer (#8). Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅ 5/8” x ½” Pulley Bushings (#61), and one M10 Aircraft Nut (#89). B.) Draw the Cable underneath the Pulley to the open bracket on the Front Base Frame (#3). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#80), two ∅ ¾” Washers (#87), and one
Resumo do conteúdo contido na página número 20
DIAGRAM 9 19
