Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
POWERHOUSE CLUB
Hardware Identifier
Assembly Instruction PHC 715
Parts List
Warranty
Ordering Parts
Model
PHC 715
Retain This
Manual for
Reference
07-20-01
OWNER'S
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Resumo do conteúdo contido na página número 4
3
Resumo do conteúdo contido na página número 5
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Rear Upright Beams (#1) by a Cross Brace (#5) in the mid-span. Align the holes and secure them with one Triangle Bracket (#12), one Bent Bracket (#13), two M10 x 3 ½” Carriage Bolts (#34), two M10 x 2 3/8” Carriage Bolts (#36)
Resumo do conteúdo contido na página número 6
STEP 2 (See Diagram 2) A.) Attach the Seat Bracket (#4) to the short pivot tube on the Main Seat Support (#3). Secure it with one M10 x 4 ¾” Allen Bolt (#39) and M10 Aircraft Nut (#42). Place the Seat Pad (#16) onto the Seat Bracket (#4). Secure it with four M6 x 5/8” Philips Head Screws (#38) and ∅ ½” Washers (#44). Insert a L-shaped Pin (#31) into the selected hole on the Seat Bracket to obtain the desired incline of the Seat. B.) Attach the side-holes of Backrest Supports (#6) to
Resumo do conteúdo contido na página número 7
STEP 3 (See Diagram 3) A.) Insert the Leg Developer Holder (#9) into the top opening on the Front Stabilizer (#2). Secure it with a Lock Knob (#33). B.) Attach the Leg Developer (#10) to the bracket on the Leg Developer Holder (#9). Secure it with an Axle (#18), two ∅ ¾” Washers (#43), and two M10 x 5/8” Allen Bolts (#40). Insert one Foam Roll Tube (#11) halfway through the hole on the Leg Developer Holder (#9). Insert two Foam Roll Tubes (#11) halfway through the holes on the Leg
Resumo do conteúdo contido na página número 8
STEP 4 (See Diagram 4) A.) Attach the Arm Curl Pad (#47) to the Arm Curl Stand (#48). Secure it with two M8 x 5/8” Allen Bolts (#46) and ∅ 5/8” Washers (#45). B.) For Arm Curl exercise, remove Leg Developer and insert the Arm Curl Stand into the opening on top of Front Stabilizer. Secure it with a Lock Knob (#33) to the selected hole to obtain the desired height. DIAGRAM 4 7
Resumo do conteúdo contido na página número 9
8
Resumo do conteúdo contido na página número 10
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Rear Upright Beam 2 2 Front Stabilizer 1 3 Main Seat Support 1 4 Seat Bracket 2 5 Cross Brace 2 6 Backrest Support 2 7 Crutch 2 8 Backrest Adjustment Bar 1 9 Leg Developer Holder 1 10 Leg Developer 1 11 Foam Roll Tube 3 12 Triangle Bracket 2 13 Bent Bracket 2 14 Bracket 1 15 Olympic Sleeve 1 16 Seat Pad 1 17 Backrest Board 1 18 Axle 1 19 Leg Developer Bushing 2 20 2 3/8” End Cap 2 21 1 ¾” Square End Cap 1 22 1” Square End
Resumo do conteúdo contido na página número 11
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cus
