Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
Hardware Pack
MWM 1801
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 1801
Retain This
Manual for
Reference
08-18-03
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
OWNER'S
Tel: (800) 999-8899 Fax: (626) 961-9966
MANUAL
www.impex-fitness.c
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 5 HOW TO USE...................................................
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
Resumo do conteúdo contido na página número 4
HARDWARE PACK 3
Resumo do conteúdo contido na página número 5
HARDWARE PACK 4
Resumo do conteúdo contido na página número 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Left Base Frame (#3) to the Right Base Frame (#1). Secure them with one Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#90). DIAGRAM 1 5
Resumo do conteúdo contido na página número 7
STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10 x 2 ½” Carriage Bolts (#82), ∅ ¾” Washers (#93), and M10 Aircraft Nuts (#90). NOTE: Do not tighten the Nuts and Bolts yet. B.) Attach the Right Seat Support (#8) to the Right Base Frame (#1). Secure it with one M10 x 2 ½” Carriage Bolt (#82), ∅ ¾” Washer (#93), and M10 Aircraft Nut (#90). C.) Attach the Right Seat Support (#8) to the Right Vertical Beam (#2). Secur
Resumo do conteúdo contido na página número 8
STEP 3 (See Diagram 3) A.) Align four ∅ 2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame (#1). Insert four Guide Rods (#5) through the Rubber Bumpers into the holes on the Right Base Frame. Slide two Selector Stems (#35) onto the Guide Rods. Insert a Selector Rod (#24) through the hole on each Selector Stem. Secure each Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#78) and ∅ ¾” Washers (#93). Please note this machine comes with 18 plates, 9
Resumo do conteúdo contido na página número 9
DIAGRAM 3 8
Resumo do conteúdo contido na página número 10
STEP 4 (See Diagram 4) A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#82), ∅ ¾” Washers (#93), and M10 Aircraft Nuts (#90). B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left Vertical Beam. Secure the Frame to the Left Vertical Beam with one Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#90). Secure the Frame to the Top Soc
Resumo do conteúdo contido na página número 11
DIAGRAM 4 10
Resumo do conteúdo contido na página número 12
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure it with a M10 x 9 ¼” Axle (#50), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#90). B.) Attach the two Front Presses (#16) to the Front Press Base (#15). Secure each Front Press with two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#90). DIAGRAM 5 11
Resumo do conteúdo contido na página número 13
STEP 6 (See Diagram 6) A.) Insert the axle on the Left Butterfly (#12) through the hole on the Left Upper Frame (#11) from the bottom up. Slide a ∅ 1 ½” Washer (#54) and ∅ 1 3/8” Lock Ring (#53) onto the Axle. Align the holes and secure the Ring with a M6 x 1 5/8” Hex Bolt (#87) and M6 Aircraft Nut (#91). Repeat the same procedure to install the other side. B.) Push two Butterfly Foam Rolls (#39) onto the Butterfly arms. DIAGRAM 6 12
Resumo do conteúdo contido na página número 14
Cable Loop Diagram for Butterfly Station 13
Resumo do conteúdo contido na página número 15
Cable Loop Diagram for Bench Press Station 14
Resumo do conteúdo contido na página número 16
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the two Swivel Pulley Brackets (#42) to the Left Upper Frame (#11). Secure each Bracket with one M12 x 4 3/8” Allen Bolt (#76), two ∅1” Washers (#92) and one M12 Aircraft Nut (#89). NOTE: Do not over tighten the Bolt. Make sure the Bracket is able to swivel. B.) Attach one end of the 83” Butterfly Cable (#29) to the clip on the Right Butterfly (#13). Pull the Cable to the right open Swivel Pulley Bracket (#42). C.) Attach a Pulley
Resumo do conteúdo contido na página número 17
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach a Chain (#51) to the Left Vertical Beam (#4). Secure it with one M10 x 1 3/8” Allen Bolt (#83), two ∅ 3/4” Washers (#93), and one M10 Aircraft Nut (#90). Attach one end of the 136” Butterfly Support Cable (#31) to the Chain using a C-clip (#63). NOTE: After complete installing all the cables, check the tightness of the cable loop system. If the cable is too loose, shorten the chain. B.) Draw the Cable to the Angled Double Pulley Br
Resumo do conteúdo contido na página número 18
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the140” Leg Press Cable (#28) to the opening hole on the Left Seat Support (#14), underneath the rubber bumper. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90). B.) Draw the Cable to the slotted opening on the Leg Press Frame (#17). Install a Pulley to the opening then secure it with two ∅5/8” x ½” Pulley Bushings (#58), one M10 x 2 3/8” Allen Bolt (#79), and
Resumo do conteúdo contido na página número 19
DIAGRAM 9 18
Resumo do conteúdo contido na página número 20
STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 114” Upper Cable (#26) to the front opening on the Right Upper Frame (#6). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#65) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅ 5/8” x ½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90). C.) Draw the Cable towards the back of the machine to the Pulley Bracket (#46). Install a Pulley to the Bracket. Secure it
