Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
®
Table of Contents
MARCY
Safety Notice
SMITH MACHINE
Hardware Identifier
MWB-4360
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB-4360
Retain This
Manual for
Reference
07-14-06
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.c
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN..................................................................
. 1 IMPORTANT SAFETY NOTICES.................................................................
2 SMITH MACHINE HARDWARE PACK
.......
............................................. 4 SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................ 6 EXPLODED DIAGRAM
. 21 SMITH MACHINE PARTS LIST
..
22
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at
Resumo do conteúdo contido na página número 4
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base, Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
Resumo do conteúdo contido na página número 5
SMITH MACHINE HARDWARE PACK 4
Resumo do conteúdo contido na página número 6
SMITH MACHINE HARDWARE PACK 5
Resumo do conteúdo contido na página número 7
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Base Frames (#1) by a Cross Brace (#2) in the mid-span. Secure each end of The Cross Brace with two M10 x 3 ½ Carriage Bolts (#79), one 4 ¾ x 2 Bracket (#36), two Ø ¾ Washers (#66), and two M10 Aircraft Nuts (#
Resumo do conteúdo contido na página número 8
STEP 2 (See Diagram 2) A.) Attach a Front Vertical Frame (#3) to the Right Base Frame (#1). Secure it with two M10 x 3 Carriage Bolts (#76), one 5 1/8 x 2 ¾ Bracket (#34), two Ø ¾ Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts yet. B.) Align a Ø 2 ½ Rubber Bumper (#59) to the hole on the Base Frame. Insert a Guide Rod (#25) through the Rubber Bumper and into the Base Frame. Secure it with one M10 x 1 Allen Bolt (#68) and Ø ¾ Washer (#66).
Resumo do conteúdo contido na página número 9
DIAGRAM 2 8
Resumo do conteúdo contido na página número 10
STEP 3 (See Diagram 3) A.) Attach the Rear Vertical Beam (#6) to the top of the Cross Brace (#2). Attach the Weight Glide Base (#8) to the Cross Brace from the Bottom. Align the holes. Secure them with two M10 x 3 Carriage Bolts (#76), Ø ¾ Washers (#66), and M10 Aircraft Nuts (#86). B.) Attach the Pulley Support Frame (#97) to the Rear Vertical Beam. Secure it with two M10 x 2 ¾ Carriage Bolts (#75), one 4 ¾ x 2 Bracket (#36), two Ø ¾ Washers (#66), and two M10 Aircraft Nuts (#86)
Resumo do conteúdo contido na página número 11
STEP 4 (See Diagram 4) A.) Attach the Weight Glide Post (#7) onto the Weight Glide Base (#8). Secure it with four M10 x 1 Carriage Bolts (#74), Ø ¾ Washers (#66) and M10 Aircraft Nuts (#86). B.) Slide the Sliding Weight Post (#14) onto the Chromed Post from the top. Place the Rear Upper Frame (#9) onto the Weight Glide Post (#7) and Rear Vertical Beam (#6). C.) Align the holes. Secure the Rear Upper Frame to the Weight Glide Post with two M10 x 3 Allen Bolts (#71), four Ø ¾ Washers (
Resumo do conteúdo contido na página número 12
STEP 5 (See Diagram 5) A. Place the Left Upper Frame (#94) onto the Front Top Beam (#15). Secure it with two M10 x 3 1/8 Carriage Bolts (#77), one 5 1/8 x 2 Bracket (#35), two Ø ¾ Washers (#66), and two M10 Aircraft Nuts (#86). B. Secure the Left Upper Frame (#94) to the Rear Upper Frame with two M10 x 2 ¾ Carriage Bolts (#75), one 4 ¾ x 2 ¾ Bracket (#101), two Ø ¾ Washers (#66), and M10 Aircraft Nuts (#86). C. Insert a Cross-Over Swivel Pulley Bracket (#99) into the sleeve on
Resumo do conteúdo contido na página número 13
STEP 6 (See Diagram 6) A.) Securely tighten all Nuts and Bolts previously installed. B.) Attach the Butterfly Base (#12) to the front of Rear Vertical Beam (#6). Attach the Butterfly Pulley Bracket (#13) to the back of the Rear Vertical Beam. Align the holes. Secure them with two M10 x 2 ¾ Carriage Bolts (#75), Ø ¾ Washers (#66), and M10 Aircraft Nuts (#86). C.) Attach the Right Butterfly (#11) to the hole on the Butterfly Base. Secure it with one Lock Ring (#56), Ø 1 ½ Washer (#67),
Resumo do conteúdo contido na página número 14
CABLE LOOP DIAGRAM 13
Resumo do conteúdo contido na página número 15
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of 87 Butterfly Cable (#42) to the clip on Right Butterfly (#11). Draw the Cable to the right Swivel Pulley Bracket (#20). B.) Attach a Pulley (#57) to the Bracket. Secure it with one M10 x 1 ¾ Allen Bolt (#69), two Ø ¾ Washers (#66), and one M10 Aircraft Nut (#86). C.) Draw the Cable around the Pulley then downward. Attach a Single Floating Pulley Bracket (#19) to the Cable. Repeat Procedure B above to install a Pulley. L
Resumo do conteúdo contido na página número 16
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Un-install the M10 x 1 1/8 Allen Bolt (#104) and M10 Aircraft Nut (#86) on the U-shaped Connector on one end of the 229 Cable (41). Remove the U-shaped Connector, Big Washer, and Ball Stopper from the Cable. B.) Insert the end of Cable through the left Cross-over Swivel Pulley Bracket (#99). Attach a Pulley (#57) to the Swivel Bracket and secure it with one M10 x 1 ¾ Allen Bolt (#69), two Ø ¾ Washers (#66), and one M10 Aircraft Nu
Resumo do conteúdo contido na página número 17
16
Resumo do conteúdo contido na página número 18
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the 138 Sliding Weight Post Cable (#102) to the open bracket on the Sliding Weight Post (#14). Secure it with one M10 x 1 Allen Bolt (#68), two Ø ¾ Washers (#66), and one M10 Aircraft Nut (#86). B.) Draw the Cable upward to the Pulley on the top of the Rear Upper Frame (#9) previously installed in Step-5. C.) Draw the Cable around the Pulley then downward. Install a Small Pulley (#103) to a Double Floating Pulley
Resumo do conteúdo contido na página número 19
DIAGRAM 9 18
Resumo do conteúdo contido na página número 20
STEP 10 (See Diagram 10) A.) Attach the 59 Lower Cable (#40) to a Pulley (#57). Attach the Pulley to the lower opening on the Rear Vertical Beam (#6). Secure it with the Foot Plate (#16), one M10 x 3 3/8 Allen Bolt (#73), two Ø ¾ Washers (#66), and one M10 Aircraft Nut (#86). Secure the Foot Plate to the Cross Brace (#2) with two M10 x1 Allen Bolts (#68), four Ø ¾ Washers (#66) and two M10 Aircraft Nuts (#86). B.) Draw the Cable underneath the Pulley to the open bracket on the Weight
