Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
CORNER GYM
Parts List
EVE-1500
Resistance Chart
Warranty
Ordering Parts
Model
EVE-1500
Retain This
Manual for
Reference
08-17-05
OWNER'S
Made under license from trademark owner Everlast
Worldwide Inc., New York.
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST………………………………………………………………………………….. 28 RESISTANCE CH
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person
Resumo do conteúdo contido na página número 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Left Base Frame and Right Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the labels in location shown. 3
Resumo do conteúdo contido na página número 5
HARDWARE PACK 4
Resumo do conteúdo contido na página número 6
HARDWARE PACK 5
Resumo do conteúdo contido na página número 7
HARDWARE PACK 6
Resumo do conteúdo contido na página número 8
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right and Left Base Frames (#1 & #14) on a flat surface. Make sure there is enough space to assemble the machine. B.) Do not tighten the nuts and bolts until instructed to do so. C.) Attach the Left Base Frame (#14) and the Right Base F
Resumo do conteúdo contido na página número 9
STEP 2 (See Diagram 2) A.) Insert two Guide Rods (#12) into the holes on the Guide Rod Base (#10). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#80) and Ø ¾” Washer (#94) from the bottom. B.) Attach the Guide Rod Base to the Left and Right Base Frames (#1 & #14). Secure each side with one M10 x 2 1/8” Allen Bolt (#83) and Ø ¾” Washer (#94). DIAGRAM 2 8
Resumo do conteúdo contido na página número 10
STEP 3 (See Diagram 3) A.) Attach the Right Vertical Beam (#3) onto the Right Base Frame (#1). Secure it with two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10 Aircraft Nuts (#97). B.) Attach the Left Vertical Beam (#17) onto the Left Base Frame (#14). Secure it with two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10 Aircraft Nuts (#97). C.) Place the Right Upper Frame (#4) onto the Right Vertical Beam (#3). Secure it with two M10 x 2 ½” Carriage Bolt
Resumo do conteúdo contido na página número 11
DIAGRAM 3 10
Resumo do conteúdo contido na página número 12
STEP 4 (See Diagram 4) A.) Slide nineteen Weight Plates (#59) onto the Guide Rods (#12). Make sure the grove on the Plates all face toward front of the machine. Insert the Selector Rod (#13) into the center hole. It is strongly recommended to spray lubricant such as WD-40 on the two Guide Rods to minimize friction. B.) Slide the Selector Stem (#58) onto the two Guide Rods and the Selector Rod. Slide the Ø 1 ¾” x 2” Rubber Bumper (#72) onto the Selector Rod. Insert a Weight Selecto
Resumo do conteúdo contido na página número 13
DIAGRAM 4 12
Resumo do conteúdo contido na página número 14
STEP 5 (See Diagram 5) A.) Attach the Right Seat Support (#2) onto the Right Base Frame (#1). Secure it with one M10 x 2 ½” Carriage Bolt (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut (#97). B.) Attach the Right Seat Support (#2) to the Right Vertical Beam (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾” Washers (#94), and two M10 Aircraft Nuts (#97). C.) Attach the Leg Developer (#7) to the bracket on the Right Seat Support (#2).
Resumo do conteúdo contido na página número 15
STEP 6 (See Diagram 6) A.) Attach the Left Seat Support (#15) to the Left Base Frame (#14). Secure it with one M10 x 2 ½”Carriage Bolts (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut (#97). B.) Attach the Left Seat Support to the Left Vertical Beam (#17). Secure it with two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾” Washers (#94), and two M10 Aircraft Nuts (#97). C.) Attach the Leg Press Frame (#16) to the bracket on the Left Base Frame (#14). Secure it
Resumo do conteúdo contido na página número 16
STEP 7 (See Diagram 7) A.) Align the Front Press Base (#19) to the Left Upper Frame (#18). Insert a 6” Axle (#52) through the holes and secure it with two Ø ¾” Washers (#94) and M10 Aircraft Nuts (#97). B.) Insert the axle on the Left Butterfly (#20) through the holes on the Front Press Base. Slide a Ø 1 ½” x Ø ¾” Washer (#66) onto the axle. Secure the axle with one Lock Ring (#65), M6 x 1 ¼” Allen Screw (#90), and M6 Aircraft Nut (#96). C.) Push a Large Foam Roll (#47) onto the Left Butt
Resumo do conteúdo contido na página número 17
Cable Loop Diagram 16
Resumo do conteúdo contido na página número 18
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach one end of the 118” Butterfly Cable (#42) to the hook on the Right Butterfly (#21). Draw the Cable to the right open Swivel Pulley Bracket (#26). B.) Attach a Pulley (#60) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two ∅ ¾” Washers (#94), and one M10 Aircraft Nut (#97). C.) Draw the Cable around the Pulley then downward. Repeat Step B above to install a Pulley to the Angled Double Floating Pulley Bracket (#27).
Resumo do conteúdo contido na página número 19
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the end of the 115” Front Press Cable (#43) to the open bracket on the Left Vertical Beam (#17). Secure it with one M10 x 1” Allen Bolt (#81), two Ø ¾” Washers (#94), and one M10 Aircraft Nut (#97). B.) Draw the Cable to the opening on the Front Press Base (#19). Attach a Pulley to the opening. Secure the Pulley to the Front Press Base with one M10 x 5 1/8” Allen Bolt (#86), two Ø ¾” Washers (#94), and one M10 Aircraft Nut (#97
Resumo do conteúdo contido na página número 20
DIAGRAM 9 19
