Resumo do conteúdo contido na página número 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
APEX Olympic Bench
Hardware Identifier
Assembly Instruction AX-PWR7
Parts List
Warranty
Ordering Parts
Model
AX-PWR7
Retain This
Manual for
Reference
04-19-05
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitn
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM.........................................................
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Resumo do conteúdo contido na página número 4
HARDWARE PACK 3
Resumo do conteúdo contido na página número 5
HARDWARE PACK 4
Resumo do conteúdo contido na página número 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with two M10 x ¾” Allen Bolts (#36) and ∅ ¾” Washers (#42). Attach a Lock Knob (#23) to the hole underneath the Main Frame. B.) Slide the Sliding Block (#8)
Resumo do conteúdo contido na página número 7
STEP 2 (See Diagram 2) A.) Attach four Bushings (#27) to a Seat Support Frame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 ¾” Allen Bolt (#37) and ∅ ¾” Washer (#42). Repeat the same procedure to install the other side. C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each Backrest Supports (#7). Align the holes and secure them with one M10 x 6 ¾” Allen Bolt
Resumo do conteúdo contido na página número 8
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). DIAGRAM 3 7
Resumo do conteúdo contido na página número 9
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x ¾” Allen Bolts (#36), and two ∅ ¾” Washers (#42). B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam Tubes halfway through the holes on the Leg Developer (#5). Push six Foam Rolls (#24) onto the Tubes from both ends. Plug six Foam Roll End Caps (#25) into the Tubes. C.) Slide the Olympic Sleeve (#20) o
Resumo do conteúdo contido na página número 10
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#41) and two ∅ 5/8” Washers (#43). Insert the Arm Curl Stand into the front opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height. B.) Attach the Curl Bar Support Frame (#11) to the open bracket on the Leg Developer (#5). Lock it with a L-shaped Pin (#21). C.) Remove the Pin, Curl Bar Handle and Arm Curl when using the Leg D
Resumo do conteúdo contido na página número 11
STEP 6 (See Diagram 6) A.) Attach an Upright Beam (#49) to a Floor Stabilizer (#47). Secure it with two M10 x 2 3/4” Carriage Bolts (#81), ∅ ¾” Washers (#42), and M10 Aircraft Nuts (#44). Do not tighten the nuts and bolts yet. B.) Attach the upper end of Left Support (#50) to the Upright Beam. Secure it with one M10 x 5/8” Allen Bolt (#88) and ∅ ¾” Washer (#42). C.) Attach the lower end of Left Support (#50) to the Floor Stabilizer (#47). Attach one end of the Rear Stabilizer (#53) to t
Resumo do conteúdo contido na página número 12
STEP 7 (See Diagram 7) A.) Attach the Front Vertical Frame (#54) to the Rear Stabilizer (#53). Secure it with two M10 x 5/8” Allen Bolts (#88) and ∅ ¾” Washers (#42). Do not tighten all the nuts and bolts yet. B.) Attach the Cross Brace (#48) to the Left & Right Supports (#50 & 51). Secure each end of Cross Brace with two M10 x 3 1/8” Carriage Bolts (#82), one 5” x 1 5/8” Bracket (#64), two ∅ ¾” Washers (#42), and two M10 Aircraft Nuts (#44). C.) Attach the Rear Vertical Frame (#52) to th
Resumo do conteúdo contido na página número 13
STEP 8 (See Diagram 8) A.) Slide the Sliding Weight Post (#56) onto the Rear Vertical Frame (#52). Slide the Sliding Pulley Bracket (#57) onto the Front Vertical Frame (#54). Use a Lock Knob (#23) to hold the Sliding Pulley Bracket in position. B.) Insert the Upper Frame (#55) into the top opening on the Front Vertical Frame (#54). Attach the rear end of Upper Frame to the Rear Vertical Frame. C.) Secure the Upper Frame with two M10 x 5/8” Allen Bolts (#88) and ∅ ¾” Washers (#42). Secure
Resumo do conteúdo contido na página número 14
CABLE LOOP DIAGRAM 13
Resumo do conteúdo contido na página número 15
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 100” Upper Cable (#68) to the opening on the front Upper Frame (#55). Make sure the ball stopper of the Cable is under the Frame. B.) Attach a Pulley (#70) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#85), two 5/8” Pulley Bushings (#79), and one M10 Aircraft Nut (#44). C.) Draw the Cable along the Upper Frame towards the back of the machine to the opening on the Upper Frame. Repeat Step B above to install a Pulley.
Resumo do conteúdo contido na página número 16
STEP 10 (See Diagram10 & Cable Loop Diagram) A.) Attach the 268” Lower Cable (#69) to the Sliding Pulley Bracket (#57). Attach two Small Pulleys (#71) to the Brackets. Secure them with two M10 x 1 ¾” Allen Bolts (#86), four ∅ ¾” Washers (#42), and two M10 Aircraft Nuts (#44). B.) Draw the Cable upward to the opening on top of the Front Vertical Frame (#54). Attach a Pulley (#70) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#85), two 5/8” Pulley Bushings (#79), and one M
Resumo do conteúdo contido na página número 17
DIAGRAM 10 16
Resumo do conteúdo contido na página número 18
17
Resumo do conteúdo contido na página número 19
18
Resumo do conteúdo contido na página número 20
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 51 Right Support 1 2 Front Stabilizer 1 52 Rear Vertical Frame 1 3 Rear Stabilizer 1 53 Rear Stabilizer 1 4 Arm Curl Stand 1 54 Front Vertical Frame 1 5 Leg Developer 1 55 Upper Frame 1 6 Seat Support Frame 2 56 Sliding Weight Post 1 7 Backrest Support 2 57 Sliding Pulley Bracket 1 8 Sliding Block 1 58 Left Safety Catch 1 9 Incline Adjustment Bar 1 59 Right Safety Catch 1 10 Foam Tube 3 60 Chrome Panel 2 11 Cu
