Resumo do conteúdo contido na página número 1
1130SB 1130SB-LSb -LSb
Owner's Manual / 96193003800 / 2009-06
Resumo do conteúdo contido na página número 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Resumo do conteúdo contido na página número 3
6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect chute is the most common cause of injury associated with the spark plug wire and keep the wire away from the snow throwers. Never use your hand to clean out the dis- plug to prevent someone from accidentally starting the charge chute.
Resumo do conteúdo contido na página número 4
PARTS PACKED SEPARATELY IN CARTON (1) FUEL STABILIZER PACKET (1) POWER CORD (198563) (1) SAFTEY IGNITION KEY (1) AUGER CONTROL ROD (193071) (1) TRACTION DRIVE CONTROL ROD (1) MULTI- (1) DISCHARGE CHUTE WRENCH (180684) EXTRA SHEAR BOLTS AND NUTS (6) SHEAR BOLTS 1/4-20 x 1-3/4 (6) SPACERS (6) LOCKNUTS (198636) (198638) 1/4-20 (73800400) ROTATOR HEAD MOUNTING (2) FLAT WASHERS (3) RETAINER SPRINGS (169675) (1) WASHER 3/8 (1) LOCKNUT 3/8 (2) CARRIAGE BOLTS (19131316) (73800600) 3/8-16 x 2.25 CHUT
Resumo do conteúdo contido na página número 5
ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the INSTALL TRACTION DRIVE CONTROL ROD chute rotator head to snow thrower and making ad just ments (See Figs. 3 and 4) to the skid plates. The traction drive control rod has the long loop on the end UNFOLD UPPER HANDLE of the spring as shown. 1. Raise upper handle to the operating position and 1. Slide rubber sleeve up rod and hook end of spring into tight en handle knobs securely. Additional carriage pivot bracket w
Resumo do conteúdo contido na página número 6
ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) The auger control rod has the short loop on the end of the spring as shown. NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 1. Place discharge chute assembly on top of chute base with discharge opening toward front o
Resumo do conteúdo contido na página número 7
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown. SPRING 1/4-20 CHUTE SHOULDER DE FLEC TO
Resumo do conteúdo contido na página número 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Resumo do conteúdo contido na página número 9
OPERATION DISCHARGE CHUTE CONTROL LEVER GAS O LINE ELECTRIC FILLER CAP START TRACTION AUGER DEFLECTOR BUTTON DRIVE REMOTE CONTROL DRIVE SPEED CONTROL MUF FLER RECOIL LEVER CONTROL CON TROL LEVER LEVER (AUXILIARY) LEVER STARTER HANDLE CHOKE CHUTE CON- DE FLEC TOR TROL PRIM ER LH TURN TRIGGER SAFETY IGNITION DISCHARGE LIGHT KEY FUEL CHUTE SHUT-OFF VALVE THROTTLE / ENGINE HANDLE KNOB CONTROL CLEAN-OUT TOOL MUF FLER TOOLBOX NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION
Resumo do conteúdo contido na página número 10
OPERATION The operation of any snow thrower can result TO USE CHOKE CON TROL (See Fig. 13) in foreign objects thrown into the eyes, which The choke con trol is located on the en gine. Use the choke can result in severe eye damage. Always wear control when ev er you are starting a cold en gine. Do not safety glasses or eye shields while operating use to start a warm en gine. your snow thrower or performing any ad just- • To engage choke, turn knob counterclockwise. Slowly ments or repairs
Resumo do conteúdo contido na página número 11
OPERATION TO THROW SNOW (See Fig. 15) • Squeeze traction drive control lever to handle to en gage the drive system. The auger rotation is controlled by the auger control lever located on the right side handle. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. • Squeeze auger control lever to handle to engage the auger and throw snow. SPEED and DIRECTION are controlled by the drive speed control lever. • Release the auger control lever to sto
Resumo do conteúdo contido na página número 12
OPERATION TO ADJUST SKID PLATES (See Fig. 19) BEFORE STARTING THE ENGINE NOTE: The wrench provided in your parts bag may be CHECK ENGINE OIL LEVEL (See Fig. 21) used to adjust the skid plates. The engine on your snow thrower has been shipped, from Skid plates are located on each side of the auger housing the factory, already filled with oil. and adjust the clearance between the scraper bar and the 1. Check engine oil with snow thrower on level ground. ground surface. Adjust skid plates evenl
Resumo do conteúdo contido na página número 13
OPERATION TO START ENGINE NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a • Be sure fuel shut-off valve is in the “OPEN” position. few minutes be fore at tempt ing to start and DO NOT push Your snow thrower engine is equipped with both a 120 Volt the primer. A.C. electric starter and a recoil starter. The electric starter 5. Pull recoil starter handle quickly. Do not allow starter is equipped with a three-wire power cord an
Resumo do conteúdo contido na página número 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. ➀ SAE 30 Motor Oil To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some See “ENGINE” in ➁ ad just ments will need to be made periodically to properly Maintenance section maintain your snow thrower. General ➂ At least once a season, check to see if you should
Resumo do conteúdo contido na página número 15
MAINTENANCE BELTS TO CHANGE ENGINE OIL Check belts for deterioration and wear after every 50 hours Determine temperature range anticipated before next oil of operation and replace if necessary. The belts are not change. All oil must meet API service classification SG–SL. ad just able. Replace belts if they begin to slip from wear. • Be sure snow thrower is on level surface. (See “TO REMOVE BELT COVER” in the Service and • Oil will drain more freely when warm. Adjustments section of this manu
Resumo do conteúdo contido na página número 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop. WARNING: To avoid serious injury, before performing any service or ad- 2. Remove safety ignition key and disconnect spark plug just ments: wire from spark plug. Place wire where it cannot come in contact with plug. 1. Be sure throttle is in STOP position. 3. Align holes in impeller hub with holes in impeller shaft 2. Remove safety ignition key. and install two (2
Resumo do conteúdo contido na página número 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 24) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the “ON” position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced. It is recommended that the belt(s) be replaced to relieve tension. by a qualified service center. 8. With tension relieved on idler, install new traction drive NOTE: It is recommended th
Resumo do conteúdo contido na página número 18
TO REMOVE WHEELS (See Fig. 25) NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts • Remove the klik pin and remove wheel from axle. dealer. Tire sealant also prevents tire dry rot and cor ro sion. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the ENGINE hole in the wheel hub (if equipped). Inner hole in axle and See engine manual. hole in wheel hub are not used fo
Resumo do conteúdo contido na página número 19
TROUBLESHOOTING See appropriate section in manual unless directed to a qualified service centre. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Refill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to FAST position. 5. Choke in OFF position. 5. Move to FULL positio
Resumo do conteúdo contido na página número 20
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB 1130SB-LSB -LSB (96193003800), PRODUCT NO. 961 93 00-38 5 11 11 6 7 15 16 14 12 8 13 11 4 12 17 3 11 10 1 9 2 33 32 34 30 31 31 26 36 29 28 20 27 21 22 23 25 35 24 23 22 2 (EXPLODED) 21 19 18 01.07.004-B NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower a
