Resumo do conteúdo contido na página número 1
2-IN-1 NAILER/STAPLER KIT
MODEL H2912/H2913
INSTRUCTION MANUAL
Model H2913
Model H2912
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
Resumo do conteúdo contido na página número 2
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
Resumo do conteúdo contido na página número 3
Safety Instructions For Power Tools 10. USE PROPER EXTENSION CORD 15. MAINTAIN TOOLS WITH CARE. for the tool. Make sure your extension Keep tools sharp and clean for best cord is in good condition. Conductor and safest performance. Follow size should be in accordance with the instructions for lubricating and chart below. The amperage rating changing accessories. should be listed on the motor or tool 16. DISCONNECT TOOLS before ser- nameplate. An undersized cord will vicing and changing accessori
Resumo do conteúdo contido na página número 4
Nailer/Stapler Safety In addition to the rules stated in the previ- ous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new nailer/stapler: 1. READ THIS ENTIRE MANUAL BEFORE OPERATING THE NAIL- ER/STAPLER. 2. ALWAYS DISCONNECT AIR FROM THE NAILER/STAPLER whenever Operating the nailer/stapler can pro- servicing or installing nails or staples. pel objects into the air, causing During maintenance, a nailer/stapler immediate eye damag
Resumo do conteúdo contido na página número 5
INTRODUCTION Most importantly, we stand behind our Commentary tools. If you have any service questions or We are proud to offer the Grizzly Model parts requests, please call or write us at H2912/H2913 2-IN-1 Nailer/Stapler. This the location listed below. model is part of a growing Grizzly family of fine power tools. When used according to Grizzly Industrial, Inc. the guidelines set forth in this manual, you 1203 Lycoming Mall Circle can expect years of trouble-free, enjoy- Muncy, PA 17756 able
Resumo do conteúdo contido na página número 6
Compressed Air System Safety Yoke Mechanism The Model H2912/H2913 is designed to be A safety yoke mechanism (bump fire) on operated at 60-100 psi. Do not exceed the nose of the nailer/stapler acts as a sec- the maximum operating pressure for ondary safety device. When the trigger is your model. pressed, the nailer/stapler will not fire until the safety yoke mechanism is depressed. Before you use your new nailer/stapler, 3 install the ⁄8" quick connect fitting that Before you use your nailer/stap
Resumo do conteúdo contido na página número 7
OPERATION 5. Push the magazine cover forward Loading The Nailer/Stapler until the magazine latch locks in place. To load your nailer/stapler: 1. Disconnect the air supply from the Depth Adjustment nailer/stapler! 1. Rotate the depth adjustment wheel 2. Push the magazine latch in the direc- (shown in Figure 3) clockwise to tion shown in Figure 1. increase the nail/staple driving depth. 2. Rotate the finger wheel counter-clock- wise to decrease the nail/staple dri- ving depth. Figure 1. Releasing
Resumo do conteúdo contido na página número 8
Clearing Jammed To operate your nailer/stapler: Staples/Nails 1. Connect the air supply to the quick The most frequent situation with any type connect fitting. of nailer/stapler is a jammed nail or staple. 2. Test the loaded nailer/stapler for prop- A jam must be cleared before using the er penetration. Hold the nailer/stapler nailer/stapler again. The two places where perpendicular to the surface of a a jam can occur is the magazine and the piece of clean scrap wood that is thick discharge are
Resumo do conteúdo contido na página número 9
Oiling The Nailer/Stapler Cleaning The Nailer/Stapler Special oil has been included with your Use a good solvent to clean the nose assembly of the nailer/stapler. Always be new Grizzly nailer/stapler to help maintain sure that the nailer/stapler is dry before its useful life. Place one drop of oil in the using it again. nailer/stapler air inlet (as shown in Figure 5) before every use. Wipe off any excess Do not allow dust, chips, sand, etc. into the oil near the nailer/stapler exhaust to avoid
Resumo do conteúdo contido na página número 10
Replacing Pistons/O-Rings If you use your nailer/stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a pis- ton or piston shaft becomes worn out. To replace a piston: Figure 6. Removing the exhaust cap. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the nailer/stapler until you can grip the piston head and remove it from the cylinder. (Be care- ful not to scratch
Resumo do conteúdo contido na página número 11
H2912 PART BREAKDOWN H2912/H2913 2-IN-1 NAILER/STAPLER -10-
Resumo do conteúdo contido na página número 12
REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PH2912001 CAP SCREW 32 PH2912032 GUIDE PLATE 02 PH2912002 CAP COVER 35A PH2912035A BUMP FIREB SWITCH 03 PH2912003 SEAL 36 PH2912036 SET SHAFT 04 PH2912004 CAP SCREW 37 PH2912037 SAFETY LEVER 05 PH2912005 SETSCREW 38 PH2912038 LOCK WASHER 06 PH2912006 CAP 39 PH2912039 CAP SCREW 07 PH2912007 PISTON STOPPER 40 PH2912040 RUBBER PAD 08 PH2912008 O-RING 41 PH2912041 CAP SCREW 09 PH2912009 COLLAR 42 PH2912042 SOCKET 10 PH2912010 O-RING 43 PH2912043 NOSE
Resumo do conteúdo contido na página número 13
H2913 PART BREAKDOWN H2912/H2913 2-IN-1 NAILER/STAPLER -12-
Resumo do conteúdo contido na página número 14
REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PH2913001 CAP SCREW 37 PH2913037 SAFETY LEVER 02 PH2913002 CAP COVER 38 PH2913038 LOCK WASHER 03 PH2913003 SEAL 39 PH2913039 CAP SCREW 04 PH2913004 CAP SCREW 40 PH2913040 RUBBER PAD 05 PH2913005 SETSCREW 41 PH2913041 CAP SCREW 06 PH2913006 CAP 42 PH2913042 SOCKET 07 PH2913007 PISTON STOPPER 43 PH2913043 NOSE COVER 08 PH2913008 O-RING 44 PH2913044 NOSE COVER 09 PH2913009 COLLAR 45 PH2913045 CAP SCREW 10 PH2913010 O-RING 46 PH2913046 CAP SCREW 11 PH
Resumo do conteúdo contido na página número 15
TROUBLESHOOTING CAUSE PROBLEM ACTION 1. O-rings in trigger valve 1. O-rings must be replaced Air leaking at trigger valve area. housing are damaged. & operation of safety yoke must be checked. Air leaking between hous- 1. Loose screws in housing. 1. Tighten screws. 2. Damaged O-ring. 2. Replace O-ring. ing and hose. 3. Loose air fitting. 3. Tighten air fitting. Air leaking between hous- 1. Damaged seal. 1. Replace damaged seals. ing and cap assembly. Tool skips staples/nails 1. Air leaks. 1. Tig
Resumo do conteúdo contido na página número 16
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
Resumo do conteúdo contido na página número 17
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #___________________________ Order #_______________________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is st
Resumo do conteúdo contido na página número 18
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT X
Resumo do conteúdo contido na página número 19
Resumo do conteúdo contido na página número 20
