Manual do usuário Grizzly G4003G

Manual para o dispositivo Grizzly G4003G

Dispositivo: Grizzly G4003G
Categoria: Torno mecânico
Fabricante: Grizzly
Tamanho: 16.47 MB
Data de adição: 4/14/2014
Número de páginas: 72
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Grizzly G4003G. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Grizzly G4003G.

Para sua conveniência

Se a consulta dos manuais Grizzly G4003G diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Grizzly G4003G no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Grizzly G4003G em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Grizzly G4003G Manual de instruções - Online PDF
Advertisement
« Page 1 of 72 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Grizzly G4003G, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Grizzly G4003G. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

MODEL G4003G
GUNSMITH'S LATHE
OWNER'S MANUAL
COPYRIGHT © MAY, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED OCTOBER, 2007 (TR)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CRTRTS9327 PRINTED IN CHINA

Resumo do conteúdo contido na página número 2

����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������

Resumo do conteúdo contido na página número 3

Table of Contents INTRODUCTION ............................................... 2 SECTION 5: ACCESSORIES ......................... 31 Foreword ........................................................ 2 SECTION 6: MAINTENANCE ......................... 33 Contact Info ................................................... 2 Basic Maintenance ...................................... 33 Machine Data Sheet ...................................... 3 Lubrication ................................................

Resumo do conteúdo contido na página número 4

INTRODUCTION Foreword Contact Info We are proud to offer the Model G4003G If you have any comments regarding this manual, Gunsmith's Lathe. This machine is part of a grow- please write to us at the address below: ing Grizzly family of fine metalworking machinery. When used according to the guidelines set forth in Grizzly Industrial, Inc. C this manual, you can expect years of trouble-free, /O Technical Documentation Manager enjoyable operation and proof of Grizzly’s com- P.O. Box 2069 mitment

Resumo do conteúdo contido na página número 5

Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G4003G GUNSMITH'S BENCH TOP LATHE WITH MODEL G4003G STAND GUNSMITH'S BENCH TOP LATHE WITH STAND Product Dimensions: Weight............................................................................................................................................................ 1213 lbs. Length/Width/Height.........................................................

Resumo do conteúdo contido na página número 6

Headstock Info Spindle Bore...........................................................................................................................................1-5/8 in. Spindle Size........................................................................................................................................... 3-1/4 in. Spindle Taper.............................................................................................................................................MT#5 No

Resumo do conteúdo contido na página número 7

Identification N I H J O K L M G P R F S T Q E U D C V B W X A Y Z AA FF CC EE BB DD Figure 1. Model G4003G identification. A. Quick Change Gearbox Levers Q. Compound Rest Handwheel B. Feed Rod Lever R. Tailstock Spindle and Center C. Emergency Stop/RESET Button S. Tailstock Spindle Lock Lever D. POWER START Button T. Tailstock Spindle Handwheel E. Inching/Jog Button U. Back Splash Guard F. Feed Direction Lever V. Tailstock G. Gear and Belt Cover W. Lead Screw H. Spindle Speed Lever (Alpha) X. S

Resumo do conteúdo contido na página número 8

� � � �� � �� � �� � � � �� � � � �� � � � �� � � �� � � � � � � �� � � � �� � � � � � � �� � � �� � � � � � �� � � � � ��� � � � � � � � � �� � � � �� � � � � � � � � � �� � � � � � � �� � �� � � � � � �� � � � � � � �� � �� � �� � � � � � � �� � �� �� � � � � � � � � �� � �� � � � � � � � �� � � � � � � ���� � � � � �� � � � � �� � � � �� � � � � � �� �� � �� �� � � � � � �� � �� � � � � � � �� � � �� � � � � � �� � � � � �� � � � � � � � �� � �� � � � � � �� � � �� � � � � �� � �� � � � � � �

Resumo do conteúdo contido na página número 9

� � � � � �� � � � � � � �� � � � �� � � �� � � � � � � � � � ��� ����� ������ �������� ���� ���� � ���� � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� ���������� ����� �� ������ ��� ��������� ���� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � ����� ���� ���������� ��������� ������� ���� � ���������� ������������� ���� ����� ���� �������� ���� ���������� �� � ����������� ���� � � � � � � � � � � � � � � � � � � � � � � �

Resumo do conteúdo contido na página número 10

Additional Safety Instructions for Lathes 1. UNDERSTANDING THE MACHINE: Read 8. PREVENTING A CUTTING TOOL/CHUCK and understand this manual before operat- CRASH: Always release automatic feeds ing machine. after completing a job. 2. CLEANING MACHINE: To avoid entangle- 9. AVOIDING STARTUP INJURIES: Make ment and lacerations, do not clear chips by sure workpiece, cutting tool, and tool post hand. Use a brush, and never clear chips have adequate clearance before starting while the lathe is

Resumo do conteúdo contido na página número 11

Glossary of Terms The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this lathe and metalworking in general. Become familiar with these terms for assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly! Arbor: A machine shaft that supports a cutting Headstock: The major lathe component that tool. houses the spindle and motor drive system to turn the workpiece. Backlash: Wear in a screw or gea

Resumo do conteúdo contido na página número 12

SECTION 2: CIRCUIT REQUIREMENTS Grounding 220V Single-Phase In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connected to the grounding prong on the plug; likewise, the outlet must be properly installed and grounded. Serious personal injury could occur if you All electrical connections must be made in accor- connect the machine to the power source dance with local codes and ordinances. before you have

Resumo do conteúdo contido na página número 13

SECTION 3: SETUP Setup Safety Items Needed for Setup The following items are needed to complete the This machine presents setup process, but are not included with your serious injury hazards machine: to untrained users. Read through this entire manu- Description Qty al to become familiar with • Fork Lift or Hoist (Rated 2000 lbs.) ............ 1 the controls and opera- • Lifting Straps (Rated 2000 lbs.) ................. 1 tions before starting the • Lifting Hooks (Rated 2000 lbs.) .....

Resumo do conteúdo contido na página número 14

BB. Cabinet Base Fasteners: Inventory —Hex Bolts M12-1.75 x 40 ........................ 6 —Flat Washers 12mm ............................... 6 — Phillips Head Screws M6-1 x 10 ........... 12 After all the parts have been removed from the — Hex Nuts M6-1 ........................................ 4 boxes, the following items should accompany — Flat Washers 6mm ............................... 12 your machine: Major Components (Figure 3) Qty. B A C A. 6" Three-Jaw Chuck w/Jaws .....................

Resumo do conteúdo contido na página número 15

Site Considerations Clean Up The unpainted surfaces are coated with a waxy Floor Load oil to prevent corrosion during shipment. Remove Your lathe is a heavy load distributed in a small this protective coating with a solvent cleaner or footprint. Place this machine on concrete floors citrus-based degreaser such as Grizzly’s G7895 only. The floor MUST be level, or the lathe frame Citrus Degreaser. To clean thoroughly, some and ways may distort over time. parts must be removed. Placement L

Resumo do conteúdo contido na página número 16

Mounting to Shop Cabinet Base Floor Assembly We recommend that you bolt your lathe to the Refer to the Base parts breakdown on Page 61 floor. Because floor materials may vary, floor for a detailed illustration and parts identification mounting hardware is not included. Since this is during the following assembly. a precision machine, it is important to level the machine with a precision level when mounting. To assembly the cabinet base: 1. Prepare the lathe location, and drill the holes

Resumo do conteúdo contido na página número 17

2. Move the apron toward the right to help bal- Lifting & Moving ance the load, as shown in Figure 8. 3. Position the chip pan on top of the base assembly so that the six lathe mounting holes align with top holes of the cabinets. 4. Un-bolt the lathe from the pallet. 5. Slowly raise the lathe from the pallet, and move it over the cabinet base at your pre- pared location. 6. Position the lathe so that the six M12-1.75 x 40 hex bolts and flat washers can be inserted You will need power liftin

Resumo do conteúdo contido na página número 18

Test Run & Break-In NOTICE NEVER shift lathe gears when lathe is operating, and make sure both the half-nut Speed Levers lever and the feed lever are disengaged before you start the lathe! Otherwise the lathe will feed the apron into the chuck or tailstock causing severe lathe damage. The purpose of the test run is to make sure the Figure 11. Headstock controls. lathe and its safety features operate correctly. 7. Push the POWER START button, then move To begin the test run & break-in p

Resumo do conteúdo contido na página número 19

4. Attach a lathe dog to the bar stock from Tailstock Setup Step 1 and mount it between the centers (as shown in Figure 13). The tailstock alignment was set at the factory with the headstock. However, we recommend that you take the time to ensure that the tailstock is aligned to your own desired tolerances. To align the tailstock: 1. Center drill a 6'' long piece of bar stock on both ends. Set it aside for use in Step 4. 2. Make a dead center by turning a shoulder to make a shank. Flip t

Resumo do conteúdo contido na página número 20

— If the stock is thinner at the tailstock end, 8. Loosen the tailstock lock lever and adjust the the tailstock needs to be moved away from tailstock offset by the amount of the taper the operator by at least the amount of the by turning the adjustment set screw (Figure taper (Figure 15). 16). Turn another 0.010'' off of the stock and check for taper. Repeat as necessary until the desired amount of accuracy is achieved. Adjustment Screw Looking down from above. Figure 15. Adjusting for tai


Manuais similares
# Manual do usuário Categoria Baixar
1 Grizzly G0509G Manual de instruções Torno mecânico 24
2 Grizzly G0516 Manual de instruções Torno mecânico 18
3 Grizzly G0456 Manual de instruções Torno mecânico 1
4 Grizzly G0509 Manual de instruções Torno mecânico 3
5 Grizzly G0584 Manual de instruções Torno mecânico 2
6 Grizzly G0602 Manual de instruções Torno mecânico 30
7 Grizzly G0554Z Manual de instruções Torno mecânico 3
8 Grizzly G0653 Manual de instruções Torno mecânico 0
9 Grizzly G0624 Manual de instruções Torno mecânico 0
10 Grizzly G0657 Manual de instruções Torno mecânico 1
11 Grizzly G0658 Manual de instruções Torno mecânico 0
12 Grizzly G0657/G0658 Manual de instruções Torno mecânico 1
13 Grizzly G0698 Manual de instruções Torno mecânico 2
14 Grizzly G0694 Manual de instruções Torno mecânico 0
15 Grizzly G0733 Manual de instruções Torno mecânico 10
16 Edelbrock 1551 Manual de instruções Torno mecânico 0
17 Bushnell 26-0100/26-0102 Manual de instruções Torno mecânico 1
18 Delta 46-715 Manual de instruções Torno mecânico 10
19 Delta 434-08-651-0006 Manual de instruções Torno mecânico 0
20 Delta 46-705 Manual de instruções Torno mecânico 0