Manual do usuário Fellowes 220-2

Resumo do conteúdo contido na página número 1

Русский
English Français Español Deutsch Italiano Nederlands Svenska Dansk Suomi Norsk Polski
220-2
220C-2
™
Get More Done Today

Resumo do conteúdo contido na página número 2

B E C N A O L M D C K I J F G H

Resumo do conteúdo contido na página número 3

Dear Customer, Thank you for buying a Fellowes Commercial Shredder. We have made many improvements in our commercial shredder since its introduction in 1982. We are confident that it offers you the greatest value for your money in its product category today. We hope it meets – or even exceeds – your expectations. To ensure years of safe, efficient use, please read these few pages about your new shredder. If this manual doesn’t answer all your questions or if you wish to comment on this product,

Resumo do conteúdo contido na página número 4

English Product Profile This product is built to shred paper, staples, small paper clips and credit cards. It is not built to shred adhesive labels, trans- parencies, newspaper, cardboard, large paper clips, or plastic (other than credit cards). Attempting to shred items not intended for this shredder may cause damage. Strip-Cut Strip-cut Confetti-cut (220-2) (220-2) (220C-2) Sheet capacity* 18-20 sheets 16-18 sheets 12-14 sheets Paper shred size 5,8 mm 3,9 mm 3,9 x 25 mm Maximum paper width 24

Resumo do conteúdo contido na página número 5

Set-Up •Make sure the back of the shredder is at least 5 cm away from walls or furniture to ensure sufficient ventilation. •Open the cabinet door and pull the waste basket (D) completely out of the cabinet. •Put plastic waste bag in basket (sample bags provided). Allow bag edges to overhang. Contact Fellowes to order more bags (part # 36054). •Slide the waste basket into the cabinet and shut the cabinet door (A). •Plug the power cord into a convenient outlet. •Store use and care manual in slot (

Resumo do conteúdo contido na página número 6

English To empty waste basket If basket full light (J) is on, follow these steps until light turns off. •Press manual forward button (F) to finish shredding any paper in the paper entry. 1 •Press the off [O] button. •Open the cabinet door (A) and pull out the waste basket (D). •Remove the full bag and replace with a new bag. •Slide the waste basket (D) into the cabinet and shut the cabinet door (A). 2 •Press and hold the reverse [R] button for a few seconds to clear paper shreds that have colle

Resumo do conteúdo contido na página número 7

Troubleshooting If there is a problem with your shredder, check these symptoms and remedies. If you can- not solve the problem, call your local dealer or contact Fellowes directly. Do not open shredder head to attempt repair. You could be exposed to serious electric shock and will void the warranty. Symptom Remedy Ready Light (G) will not light Make sure shredder is plugged in. Press the automatic button [I]. Shredder does not start or stops while • Make sure shredder is plugged in. shredding

Resumo do conteúdo contido na página número 8

English Fellowes conducts extensive testing to ensure that these shredders are capable of meeting all of the specifications listed in the Product Profile (see page 3). However, the actual sheet capacity is dependent on a number of factors including the type and weight of paper, the humidity, the voltage level of the power source, the temperature of the motor, and the care with which the operator feeds the paper. Safety agency testing is conducted to ensure that the shredder will oper- ate to spe

Resumo do conteúdo contido na página número 9

Declaration of Conformity Fellowes Yorkshire Way, West Moor Park, Doncaster, South Yorkshire, DN3 3FB England declares that the product Models 220-2 and 220C-2 conform with the requirements of the Low Voltage Directive (73/23 EEC) and the Electromagnetic Compatibility Directive (89/336 EEC) and the following harmonized European Normes (EN Standards) and IEC Standards. Safety: EN60950 ‘Information Technology Equipment’ EMC: Standard Severity Level Performance Criteria EN 61000-4-2: 1995 3AD,