Resumo do conteúdo contido na página número 1
INSTRUCTION MANUAL
1/2 HP 12 Speed
Drill Press
with Laser Line Generator*
* Patent Pending
• Melbourne • Perth • Auckland • Hong Kong • Shanghai
LDP13F
• Taipei • New York • Verona • London • Paris
040614 ED6 JJ
Resumo do conteúdo contido na página número 2
Contents Full 2 Years Home Use Warranty Warranty 2 Whilst every effort is made to ensure your complete Introduction 3 Environmental protection 3 satisfaction with this tool, occasionally, due to the mass Description of symbols 3 manufacturing techniques, a tool may not
Resumo do conteúdo contido na página número 3
Symbols Dear Customer The rating plate on your tool may show symbols. These If you require any help with your product, whether it represent important information about the product or is a Warranty claim, spare part or user information, instructions on its use. please phone our Help Line for an immediate response. Wear hearing protection. Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. Wear eye protection. Wear breathing protection. Introduction Conforms to EMC regulations
Resumo do conteúdo contido na página número 4
Safety rules for laser lights General safety instructions The laser light/laser radiation used in the GMC REDEYE® To use this tool properly, you must observe the safety system is Class 1 with maximum 1mW power and 650nm regulations, the assembly instructions and the operating wavelengths. These lasers do not normally present an instructions to be found in this Manual. All persons who optical hazard, although staring at the beam may cause use and service the machine have to be acquainted with
Resumo do conteúdo contido na página número 5
7. Dress correctly. Do not wear loose clothing or 17. Stay alert. Watch what you are doing. Use common jewellery. They can be caught in moving parts. Rubber sense. Do not operate a power tool when you are tired. gloves and non-slip footwear are recommended when 18. Check for damaged parts. Before using a tool, working outdoors. If you have long hair, wear a check that there are no damaged parts. If a part is protective hair covering. slightly damaged, carefully determine if it will opera
Resumo do conteúdo contido na página número 6
12. If the workpiece overhangs the table such that it will Additional safety rules for drill presses fall or tip if not held, clamp it to the table or provide Warning. For your own safety, do not try to use your drill auxiliary support. press or plug it in until it is completely assembled and 13. Set the drill press to a speed appropriate to the job. installed according to the instructions and until you have read and understood the following: 14. Do not start the drill press while the dr
Resumo do conteúdo contido na página número 7
Caution! Do not expose to rain or use in damp locations. Required tools Warning! For your own safety read instruction manual The following tools are required to assemble the drill press before operating drill press. Wear eye protection, do not • 3mm, 4mm, 6mm Hex Keys (Supplied) wear gloves, necktie or loose clothing, clamp workpiece • 16mm Wrench (Not Supplied) or brace against column to prevent rotation, use • Phillips Head Screwdriver (Not Supplied) recommended speed for drill accessor
Resumo do conteúdo contido na página número 8
Accessories The LDP13F is supplied with the following components: 1. B ase 2. Column 3. Rack 4. Rack Collar 2 3 4 1 5. Table 6. Belts (x2) 7. Handle 8. Keyless Chuck 9. Extension Table Locking Knobs (x4) 10. Motor Head 11 . Handle 12. Depth Scale 13. Table Lock 14. Worm 5 6 7 15. Hex Keys (x3) 16. Bolts for attaching column to base (x4) 17. Bolt to attach handle 8 9 10 11 12 13 14 15 16 17 8
Resumo do conteúdo contido na página número 9
1 18 4 Know your product 1. Laser light on/off switch 10 11 10 2. Laser aperture (x2) 3 3. On/off switch 15 4. Pulley cover 17 16 5. Base 2 6. Column 13 7. Rack 8. Rack Collar 8 9. Table/Support Assembly 10. Belts (x2) 11. Belt Tension Lever 12. Table Handle 7 13. Keyless Chuck 14. Extension Table 12 19 Locking Knobs (x4) 15. Motor Head 14 16. Feed Handle 13 17. Depth Gauge 18. Depth Scale/Lock 19. Table Lock 20. Bevel Scale 6 21. Hex Keys 20 21 5 9
Resumo do conteúdo contido na página número 10
Assembly 1. Place base on floor. 2. Place column assembly on base and align the 4 holes in the column assembly with the holes in the base. 3. Using the 4 10mm diameter x 46mm long bolts secure the column support to the 12. Fit the rack collar over the base and tighten with a column and bring it down 16mm wrench. to the top of the rack. 4. Loosen the screw on the rack Ensure the bevel side is collar using the 4mm hex key. down over the rack. 5. Remove the rack collar by 13. Tighten t
Resumo do conteúdo contido na página número 11
16. Fit the table lock into the Note. Fit the lower belt on first. table support assembly and Note. When fitting belts it is tighten to secure the table. easier to place the belt onto 17. Fit the depth scale/lock the small pulley and then turn onto the handle. it onto the larger pulley. 18. Fit the handle and depth 23. To tighten the belts on scale onto the motor head the pulleys pull the motor ensuring that the flats on backwards. This is best the handle locate the flats done by grab
Resumo do conteúdo contido na página número 12
1. Loosen the screw under the table by rotating it in an Installing and removing drill bits anti-clockwise direction. Caution. Always ensure that the drill press is switched 2. Tilt the table to the desired angle as indicated on the off and the plug is removed from the power point before bevel scale. making any adjustments. 1. Loosen the chuck sufficiently so that the jaws are open wide enough to allow a bit to be inserted. The chuck is loosened by rotating the collar in a clockwise direct
Resumo do conteúdo contido na página número 13
mm in 0 0 1 ® R E D E Y E 2 • Improved Drilling Vision Ł 1 • Faster Set-up 3 • Increased AccuracyŁ 4 • Safer Working Ł 1. Remove the plug from the mains socket. 5 2 Environment 2. Take off the pulley cover. 1/2 HP LASER LIGHT. LASER RADIATION LDP13F Drill Press with Laser Line 6 Do not stare into beam. 230V–240Vac ~ 50Hz 375W no. 230–2470 RPM Only turn laser beam on when tool Ø13mm EARTHED APPLIANCE is on work piece. Class 1 laser product Always wear ear and eye pro3 tect. ion . IL f coo r
Resumo do conteúdo contido na página número 14
Turning on and off Adjusting the laser 1. To start the drill press insert 1. Clamp a scrap piece of the switch disabling insert material to the table. and move the switch up to 2. Insert a drill bit into the the ‘ON’ position. chuck jaws. 2. Move the switch down to the 3. Turn on the drill press. ‘OFF’ position to turn the drill 4. Using the feed wheel lower press off. the spindle and make a small 3. Remove the switch disabling mark in the workpiece. insert to prevent unauthorised 5. Tu
Resumo do conteúdo contido na página número 15
speed as required for the application. • Bend or burn bits • Produce off-centre or irregular shaped holes 2. Insert the drill bit required for the application. • W hen drilling large holes in metal it is recommended to 3. Mark the drilling points on the work piece. drill with a small bit at first, then finish with a larger bit. 4. Switch on the laser line and line up with the drilling Also, lubricate the bit with oil to improve drilling action point with the intersection point of the two bea
Resumo do conteúdo contido na página número 16
Troubleshooting Warning. Turn the on/off switch to the off position and unplug the tool from the power supply before performing trouble shooting procedures. Troubleshooting Problem Cause Solution Drill press will not start Power cord not plugged in Ensure that the cord is connected to the power supply Power fault, fuse or circuit breaker tripped Check the power supply Cord damaged Use authorised service centre to repair or replace Faulty switch Use authorised service centre to repair or repl
Resumo do conteúdo contido na página número 17
17
Resumo do conteúdo contido na página número 18
18
Resumo do conteúdo contido na página número 19
19
Resumo do conteúdo contido na página número 20
Carefully read the entire Instruction Manual before using this product. With continuing product development changes may Before returning this product for a have occurred which render the product received Warranty Claim or any other reason slightly different to that shown in this instruction Please Call 1300 880 001 (Australia) manual. The manufacturer reserves the right to or 0800 445 721 (New Zealand) change specifications without notice. Note: Specifications may differ from country to
